Kenmore Dishwasher 665.16014402 (66516014402, 665 16014402) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10348409
This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.
- Provides threaded fastening for panels, brackets, covers, or internal components
- Replaces worn, rusted, stripped, or missing hardware
- Helps reduce vibration and rattling from loose parts
- Restores proper alignment and a secure fit of attached parts
What's included: Includes 1 screw. Installation notes:
- Disconnect power; turn off water supply before service
- Note original screw location and retain any spacers or clips for reassembly
- Start threads by hand to avoid cross-threading
- Tighten snugly; do not overtighten to prevent stripping
Do-It-Yourself Stories from Customers like You
Dishwasher would not start Mark M. • Midlothian , VA • July 16, 2016
Maytag Dishwasher (about 5 years old). Some of the buttons had stopped functioning. Then the Start button began choosing whether or not to work. Eventually it would not start at all. Upon removing the control panel, the first thing I noticed was that the brackets that hold the two lower screws were broken. (So this was the reason that the door was so hard to open from the time it was new.) I trouble shot the thermal fuse, the door-latch switches, and inspected the control board trying to find...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9741232
Quantity of ONE.
Size: 8-18 x 5/8 inch.
(#8 screw, 18 threads per inch, 5/8 inch long)
Do-It-Yourself Stories from Customers like You
Leaking around dishwasher door previous repair missing parts Patrick R. • Peachtree City , GA • November 15, 2014
I ordered new seals from AppliancePartsPros.com. Finding the right seals was very easy, all based on model number of the appliance. While looking my unit over for other signs of wear, I noticed that a repair done by the prior homeowner to the lower wash arm was done improperly: a seal there was set protruding from the cover, the cover was missing screws, and the arm was missing the upper bushing. So I ordered a new seal, the missing screws, and both the top and bottom bushings (just to be...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10358302
Goes from pump to exterior drain hose.
Do-It-Yourself Stories from Customers like You
Dishwashwer was only partially draining James M. • Barre , MA • November 07, 2016
I figured out that it was probably a plugged pump hose, since the pump would run, it somtimes it drained and sometimes it didn't. Your video helped with how to take the dishwasher out and replace the hose. I replaced the hose and everything is now working fine. It turned out to be a broken check valve in the old hose that caused the problem. It took 90 mins to do the repair.
Read more
More
$52.95
- Compare At:
-
$62.48
- You Save:
-
$9.53
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268909
Overfill control.
Do-It-Yourself Stories from Customers like You
Washer would not fill with water Ty J. • Hillsboro , OR • July 08, 2018
Replaced float switch and also replaced intake valve. Worked like a charm and the process was as easy as the YouTube video I followed made it seem.
Read more
More
$45.95
- Compare At:
-
$54.22
- You Save:
-
$8.27
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8531857
This inlet protector is the coarse screen that covers the dishwasher's pump/sump inlet, blocking large debris from entering the wash system. Replacing a damaged or missing protector helps maintain water flow and protect the pump from jams or wear.
- Screens large food particles and debris from the pump/chopper inlet
- Helps maintain proper water circulation and consistent cleaning performance
- Reduces risk of pump damage or noisy operation from debris
- Common signs: cracked or missing screen, persistent debris in the sump, grinding/rumbling noises, or declining wash results
What's included: 1 inlet protector Install notes:
- Disconnect power and shut off water supply before servicing
- Remove the lower rack and spray arm; access the sump/accumulator area per your model
- Lift out the old protector; seat the new protector fully and secure any tabs/fasteners
- Reassemble and ensure the screen sits flat with no gaps
Do-It-Yourself Stories from Customers like You
Clogged at the chopper assembly strange noisehopper assembly broken Thomas H. • Idaho Falls , ID • July 07, 2015
Looked at Dishwasher. Scratched head and armpit. Told wife I would fix, not repariman. Wife skeptical - shook head. Found schematic on web. Found YouTube video of guy repairing same DW model. Disassembled. Diagnosed problem. Chopper assembly welded in place by water scale -broke removing. Potty mouth. Ordered parts. Waited for parts. Washed dishes by hand. Wife doing ok. Parts arrived (in only a day or two!!! Fed Ex for 7 bucks!! Great deal). Put on nasty t-shirt, baggy shorts. ...
Read more
More
$78.57
- Compare At:
-
$94.74
- You Save:
-
$16.17
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10477552
This heater terminal nut fastens the heating element's electrical connector to its stud, keeping the connection tight under heat and vibration. Replacing a worn or missing nut restores safe contact and consistent heating performance.
- Secures the wire/ring terminal to the heater stud for a solid electrical connection
- Helps prevent arcing, discoloration, and heat damage from a loose connection
- Signs include a loose terminal, burnt odor, or melted/charred insulation at the heater connection
What's included: 1 heater terminal nut
- Disconnect power and allow the appliance and element to cool completely before service
- Photograph wiring for reference; remove old hardware and clean the terminal
- Inspect the ring terminal, insulators, and stud; replace any heat-damaged components
- Start threads by hand to avoid cross-threading; snug with the correct nut driver—do not overtighten
Do-It-Yourself Stories from Customers like You
Stopped running after rinse cycle and the clean light was flashed 3 times Clyde Y. • Turtle Creek , PA • August 29, 2015
Replaced the heating element as shown in the video. Repaired a bad connector on the wire leading to the heating element. The clean light still flashed 3 times. Determined that the thermal fuse also needed to be replaced. Replaced the thermal fuse as shown in the video. The clean light now flashed 7 times which I discovered meant that the control panel needed to be reset. I then reset the control panel by pressing the buttons: normal, heated dry, normal, heated dry. It now works perfectly.
Read more
More
$9.95
- Compare At:
-
$11.84
- You Save:
-
$1.89
Genuine Whirlpool part
By: Whirlpool
Part Number: 72032
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$17.76
- Compare At:
-
$21.13
- You Save:
-
$3.37
Genuine Whirlpool part
By: Whirlpool
Part Number: W10817436
This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.
- Fastens brackets, panels, and internal components to their mounting points
- Maintains alignment and reduces vibration during operation
- Replaces missing, worn, rusted, or stripped hardware
- Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position
What's included: 1 screw Install notes:
- Disconnect power; shut off water or gas supply if applicable
- Align the part being secured and remove any damaged hardware
- Hand-start threads to avoid cross-threading; tighten with the correct driver
- Do not overtighten; verify the assembly is secure and operates freely
Do-It-Yourself Stories from Customers like You
Wheel tub broken. Paul K. • Belleville , NJ • January 11, 2019
Replaced Wheel-Tub.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: W11027055
This heater support holds the heating element securely in place inside the appliance, maintaining correct alignment and clearance for reliable operation. Replacing a worn or broken support helps prevent sagging, noise, or damage from an out-of-position element.
- Secures the heating element to its mounting point to keep it stable
- Maintains proper spacing from nearby components and surfaces
- Helps reduce vibration, rubbing, or rattling noises
- Replace if the original support is cracked, warped, missing, or the element appears misaligned
What's included: 1 heater support. Install notes:
- Disconnect power to the appliance before servicing; allow hot components to cool
- Access the heater per your model's service information; note the original orientation and routing
- Seat the support fully and handle element leads carefully to avoid damage
Do-It-Yourself Stories from Customers like You
Not cleaning well, silverware very bad. Walter M. • Labelle , FL • December 10, 2017
Replaced spray arms and tube. Found all had debris in them and prohibited water pressure from reaching items. After replacement everything comes out sparkling. Don't understand how the spray arms getting plugged. Almost like waste water is recycled. Turns out to be a very easy project and if needed AppliancePartsPro has information and directions available at your finger tips.!
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268990
Bushing, Door spring
Do-It-Yourself Stories from Customers like You
Door spring was week or broke Ronald O. • Saginaw , MI • February 26, 2016
Purchased door springs from Appliance Parts pros.com, installed them and door on our Dishwasher was back to normal, Had to pull out dishwasher from under cupboard to get to springs, as they were on the sides of the dishwasher.
Read more
More
$57.22
- Compare At:
-
$68.09
- You Save:
-
$10.87
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8535083
This replacement upper spray arm restores strong spray coverage to the upper wash level of your dishwasher. It channels water through its jets and spins under pressure to help deliver consistently clean dishes on the top rack.
- Directs pressurized wash water to the upper wash level for thorough cleaning
- Rotates under water pressure for even spray coverage
- Helps clear food soils and detergent residue from dishes and glasses
- Common symptoms: poor cleaning on the upper rack, spray arm not spinning, clogged or cracked arm
What's included: 1 upper spray arm Install notes:
- Disconnect power and shut off the water supply before servicing
- Open the dishwasher; remove the upper rack if needed for access
- Release or unthread the retainer and pull the old arm straight off; clear debris from the hub/feed port
- Seat the new arm and secure the retainer hand-tight; ensure the arm spins freely and run a test cycle
Do-It-Yourself Stories from Customers like You
Dishwasher not working well Andrew S. • Chico , CA • February 03, 2017
This is a 12 year old Kenmore, but my experience applies to many dishwashers. The machine had run for almost a year without being cleaned. I found parts had failed from age and water passages were jammed with hard-water deposits and pieces of food, labels, etc. that had gotten past the filters. I cleaned out what I could and replaced parts that could not be cleaned or were damaged. Dishwasher now works better than it has for years. The work, including ordering parts, took about 4 hours, but...
Read more
More
$46.95
- Compare At:
-
$55.40
- You Save:
-
$8.45
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489069
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Broken handle foot pedal and missing parts Donald M. • Lake Arrowhead , CA • April 05, 2015
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy!
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8269296
Located between the console and door
More
$76.66
- Compare At:
-
$91.23
- You Save:
-
$14.57
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10073520
This foam pad installs between the inner and outer door panels of a dishwasher to dampen sound and help shield the outer panel from heat and moisture, keeping operation quieter and the door better protected. What it does:
- Lines the inside of the outer door panel to reduce operating noise and vibration
- Acts as a thermal and moisture barrier for the outer door panel
- Helps maintain proper door performance when the original insulation is worn or missing
- Replace if torn, degraded, or waterlogged, or if noise/condensation around the door has increased
What's included:
Install notes:
- Disconnect power and shut off water to the dishwasher before servicing
- Support the door; remove perimeter screws to separate the inner and outer door panels
- Note the pad's orientation; seat the new insulation evenly without pinching wires or harnesses
- Reassemble panels and fasteners; verify smooth door/latch operation
More
$45.95
- Compare At:
-
$55.14
- You Save:
-
$9.19
Genuine Whirlpool part
By: Whirlpool
Part Number: 4392899
Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.
Do-It-Yourself Stories from Customers like You
Lack of accurate control on 2 electric range burners Jeff D. • Neenah , WI • April 09, 2016
Ordered 2 infinite burner controls from Appliance Parts Pros and watched the online video on the replacement of them at the same time. When they arrived promptly, I was ready to take on the job.
The fix only took about 15 minutes because I was prepared after watching the video.
Read more
More
$17.76
- Compare At:
-
$21.31
- You Save:
-
$3.55
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268913
This dishwasher overfill control float mounts in the tub floor and rises with the water level to trip the float switch and stop filling. Replacing a warped or stuck float restores proper fill control and helps prevent leaks. What it does:
- Monitors tub water level and actuates the float switch to shut off the inlet valve
- Helps prevent overfilling and water leaking from the door
- Common symptoms of a faulty float include no fill, continuous filling/overfilling, or inconsistent water level
What's included:
Install notes:
- Disconnect power and turn off the water supply before servicing
- Remove the lower rack; lift out the old float
- Access beneath the tub may be required to release/install the retainer
- Ensure the float stem engages the switch lever and moves freely; test-fill and check for leaks
Do-It-Yourself Stories from Customers like You
The display buttons kept flashing and the dishwasher would shut off Lynn P. • Pooler , GA • June 28, 2016
Replace the motherboard and used YouTube to replace float switch. Part ordered was exactly what I needed
Read more
More
$55.95
- Compare At:
-
$66.58
- You Save:
-
$10.63