Kenmore Dishwasher 665.16024401 (66516024401, 665 16024401) Parts

We bought replacement parts from you and my daughter fixed it. It is working now. It would have been nice if all the parts came in a set. Read more

I had no hope of separating the panel from the frame without damaging the frame since the two parts were rusted pretty badly and the screws holding the panel to the frame were completely beyond salvage. So I had to replace both the panel and the frame. I ended up removing the electrical/electronic connections, removing the panel/frame from the hinge and then replacing it with the new parts. Took about 90 minutes but the hardest part was removing other items from the rusting frame without... Read more

I reviewed the schematic and saw the Volute Seal, and Impeller Seal were the two that were closest my source of water. After watching the video about changing the Impeller/seal I removed the motor, impeller, and volute; I found that the impeller seal was the faulty one in my case. Since I'd ordered the volute and impeller seal kits (as I wasn't sure which it was) I installed both while I had it apart. Runs great, no water - simple to do. The seal changes took about 20 minutes. The only... Read more

• Door latch failure

I ordered this part and switched the previously used one. Read more

We bought replacement parts from you and my daughter fixed it. It is working now. It would have been nice if all the parts came in a set. Read more

Replaced wash arm mount Read more

Read directions on how to change the power cord and watched video on your site on how to change the drain hose. Everything went perfectly. Read more

Maytag Dishwasher (about 5 years old). Some of the buttons had stopped functioning. Then the Start button began choosing whether or not to work. Eventually it would not start at all. Upon removing the control panel, the first thing I noticed was that the brackets that hold the two lower screws were broken. (So this was the reason that the door was so hard to open from the time it was new.) I trouble shot the thermal fuse, the door-latch switches, and inspected the control board trying to find... Read more

Pulled a video from online and ordered my parts from Appliancepartspros.com. This was the second repair I've done with your help, the last being my washing machine. This time I replaced the dishwasher detergent dispenser on my Kitchen Aid. You guys make it so simple and give me the confidence to do it myself! Read more

While at my sister's house, she showed me how to access & dismantle the housing unit on her dishwasher, thinking the issue might be from that area. So, when I came home, I opened up my housing unit and found that several of the screws had come out and the pump outlet seal was stretched out and partially outside of the unit itself. I located all of the missing screws & discovered I was still missing one, which my husband helped me order with the pump outlet seal. I easily replaced the old seal... Read more

Kick plate was easy; screw holes in the wrong place, but used double-sided tape instead and worked great. Didn't need the extra screws ordered; it came with them. The roller spindles should be sent with a packet of grease. When replaced, the door was even louder than previous. Used candle wax on the spindles and it's quiet as can be now. Read more

I figured out that it was probably a plugged pump hose, since the pump would run, it somtimes it drained and sometimes it didn't. Your video helped with how to take the dishwasher out and replace the hose. I replaced the hose and everything is now working fine. It turned out to be a broken check valve in the old hose that caused the problem. It took 90 mins to do the repair. Read more

Replaced the heating element as shown in the video. Repaired a bad connector on the wire leading to the heating element. The clean light still flashed 3 times. Determined that the thermal fuse also needed to be replaced. Replaced the thermal fuse as shown in the video. The clean light now flashed 7 times which I discovered meant that the control panel needed to be reset. I then reset the control panel by pressing the buttons: normal, heated dry, normal, heated dry. It now works perfectly. Read more

Replaced float switch and also replaced intake valve. Worked like a charm and the process was as easy as the YouTube video I followed made it seem. Read more

Looked at Dishwasher. Scratched head and armpit. Told wife I would fix, not repariman. Wife skeptical - shook head. Found schematic on web. Found YouTube video of guy repairing same DW model. Disassembled. Diagnosed problem. Chopper assembly welded in place by water scale -broke removing. Potty mouth. Ordered parts. Waited for parts. Washed dishes by hand. Wife doing ok. Parts arrived (in only a day or two!!! Fed Ex for 7 bucks!! Great deal). Put on nasty t-shirt, baggy shorts. ... Read more

Replaced spray arms and tube. Found all had debris in them and prohibited water pressure from reaching items. After replacement everything comes out sparkling. Don't understand how the spray arms getting plugged. Almost like waste water is recycled. Turns out to be a very easy project and if needed AppliancePartsPro has information and directions available at your finger tips.! Read more