Kenmore Dishwasher 665.16634000 (66516634000, 665 16634000) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 717000
This seal kit is for the main tub. It goes around the pump housing.
Do-It-Yourself Stories from Customers like You
Leaks from around the door and from the pump motor Samuel M. • Sudbury , MA • January 12, 2016
1. To fix the leaks from around the door, I replaced the upper and lower door seals. These were purchased in a separate transcation, so they are not the parts shown here. The upper door seal worked as intended, but the lower seal would not stay in place on the lower edge of the door during a wash. Therefore I cleaned the grease and detergent off the old seal, and installed using silicone sealer/adhesive. The plastic edge pieces for the lower seal were supplied with the kit, and they installed...
Read more
More
$37.95
- Compare At:
-
$45.16
- You Save:
-
$7.21
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302711
This pump outlet seal sits on the discharge side of the dishwasher pump to keep the outlet connection watertight. Replacing a worn seal helps stop leaks and keeps wash water contained during the cycle. What it does:
- Seals the joint at the pump outlet to prevent water leakage
- Helps maintain proper circulation by keeping the pump discharge airtight/watertight
- Common symptoms of failure include water under the unit, drips near the pump area, or a flattened/cracked/hardened old seal
What's included:
Install notes:
- Disconnect power and shut off the water supply before servicing
- Remove the toe-kick/lower access panel to reach the pump area; place a towel or pan to catch residual water
- Note seal orientation; clean mating surfaces before installing the new seal
- Seat the seal evenly; reassemble and run a short test to check for leaks
Do-It-Yourself Stories from Customers like You
Loud dishwasher producing dirty dishes Leon F. • Sylmar , CA • November 11, 2015
I nearly shelled out for a new Kitchenaid when I remembered APP and entered my model # just for fun. The interactive diagrams and install videos showed where all the parts "should" be, mine were badly disintegrated, so I replaced the damaged ones and swapped out all of the other easily accessible seals and bearings (also gave it a good and very disturbing cleaning). My parts surprisingly arrived next day and for about $40, the dishwasher is quiet and works like new again.
Read more
More
$24.95
- Compare At:
-
$29.94
- You Save:
-
$4.99
Genuine Whirlpool part
By: Whirlpool
Part Number: 4317824
The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.
Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.
Symptoms of a bad power cord include:
- The dishwasher not turning on or completing cycles
- Warm or hot power cords during operation
- Frayed, cracked, or exposed copper wiring
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Mice chewed the drain hose and power cord Noah C. • Eastsound , WA • February 16, 2015
Read directions on how to change the power cord and watched video on your site on how to change the drain hose. Everything went perfectly.
Read more
More
$20.95
- Compare At:
-
$24.93
- You Save:
-
$3.98
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10253040
This genuine OEM part is a refrigerator upper dishrack. The upper dishrack is the tray on which dishes are placed on the top shelf of a dishwasher. If the dishrack is no longer sliding on its tracks, or is not staying in place during the wash cycle, it might need to be replaced. Luckily this is a very simple repair.To replace the upper dishrack, simply pull out the old dish rack and lift it up out of its tracks. Once removed from the dishwasher, take the new dishrack and gently slide it into place. Make sure it is placed correctly and that it is running smoothly on its tracks.This replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.
Do-It-Yourself Stories from Customers like You
The upper rack of our dishwasher needed replacing Lenwood J. • Statesville , NC • June 07, 2014
Ordered the part from Appliance Parts Pros, it arrived about a week later and it was the correct part. I liked the cross reference and confirmation of the correct part that was available on the website before placing an order.
Read more
More
$242.21
- Compare At:
-
$285.81
- You Save:
-
$43.60
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9741232
Quantity of ONE.
Size: 8-18 x 5/8 inch.
(#8 screw, 18 threads per inch, 5/8 inch long)
Do-It-Yourself Stories from Customers like You
My dishwasher was leaking out copious amounts of water while cycling Michael K. • Oakland , MI • July 11, 2019
While at my sister's house, she showed me how to access & dismantle the housing unit on her dishwasher, thinking the issue might be from that area. So, when I came home, I opened up my housing unit and found that several of the screws had come out and the pump outlet seal was stretched out and partially outside of the unit itself. I located all of the missing screws & discovered I was still missing one, which my husband helped me order with the pump outlet seal. I easily replaced the old seal...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268874
This lower spray arm assembly circulates wash water from the pump to clean dishes on the lower rack. The integrated shield helps direct water flow and protect the arm from debris, restoring consistent wash coverage.
- Distributes high-pressure water across the lower rack for effective cleaning
- Shield design helps prevent debris intrusion and improves spray pattern
- Common failure signs: poor lower-rack cleaning, noisy or restricted rotation, cracked or warped arm, clogged spray holes
- Also addresses leaking or splashing caused by a damaged or misaligned arm/shield
What's included: One lower spray arm with attached shield Install notes:
- Disconnect power and turn off water supply before servicing
- Remove lower rack; lift off old arm assembly per model design
- Clear any debris from pump outlet and sump before installing
- Ensure the new arm spins freely and is fully seated; test for smooth rotation
Do-It-Yourself Stories from Customers like You
Dishwasher was noisy not cleaning well and spray arms were loose Steve S. • Rochester , MN • September 10, 2016
Replaced upper and lower spray arms, plus nylon bearings.
Read more
More
$70.76
- Compare At:
-
$84.91
- You Save:
-
$14.15
Genuine Whirlpool part
By: Whirlpool
Part Number: WP676455
Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.
Do-It-Yourself Stories from Customers like You
Rusty tips on tops of posts in top and bottom racks of kitchen aid dishwasher James O. • Bedford , OH • July 04, 2016
Used the vinyl touch up paint on the tops of posts and slid vinyl tips over 130 posts. The paint acts as an adhesive to keep the tips secure.
Read more
More
$24.95
- Compare At:
-
$29.69
- You Save:
-
$4.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9740674
This drain cover gasket seals the drain/pump cover at the bottom of the dishwasher tub to keep wash water contained. Replacing a cracked or flattened gasket helps stop leaks from the base and protects nearby components.
- Creates a watertight seal between the drain cover and sump opening
- Helps prevent leaks onto the floor or into the dishwasher base during cycles
- Common signs of failure: puddles beneath the unit, dampness in the base, or a visibly hardened/cracked gasket
- Good practice to replace when the drain cover is removed for service to ensure a proper reseal
What's included: 1 drain cover gasket Install notes:
- Disconnect power and shut off water supply before servicing
- Remove the lower rack (and spray arm if required) to access the drain cover per your model
- Clean mating surfaces; install the new gasket evenly without twists
- Reassemble and run a short cycle while checking for leaks
Do-It-Yourself Stories from Customers like You
Debris got into the impeller and broke it Thomas L. • Westport , MA • November 30, 2014
Replaced the drain & wash impeller kit.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10258149
Supplies water to the spray arm.
Do-It-Yourself Stories from Customers like You
The water parts were broken the washer is about 16 years old Katrina M. • Fontana , CA • July 14, 2018
We bought replacement parts from you and my daughter fixed it. It is working now. It would have been nice if all the parts came in a set.
Read more
More
$52.95
- Compare At:
-
$63.01
- You Save:
-
$10.06
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3373234
This dishwasher door spring bushing—also called a door spring bearing—sits at the spring's frame anchor to provide a pivot and reduce wear. Replacing a worn bushing restores door balance and helps prevent the door from dropping or slamming open.
- Provides the pivot/anchor surface for the door spring at the cabinet frame
- Maintains balanced door opening and closing force
- Reduces friction, wear, and squeaks at the spring connection
What's included: Includes 1 bushing. Install notes:
- Disconnect power at the breaker and shut off water supply.
- Remove the toe panel and mounting screws; slide the dishwasher out slightly to access the door springs.
- Support the door, release spring tension, replace the bushing at the frame anchor, and reattach the spring.
- Inspect both sides and replace worn components in pairs to keep door tension even.
Do-It-Yourself Stories from Customers like You
The dishwasher door spring broke. Rachael T. • Junction City , OR • November 07, 2022
I ordered the parts, deciding that if one spring had broken, the other one should probably be replaced at the same time. I followed the suggestion of ordering the door spring bearing given on the ordering page, and since I had not yet pulled out the dishwasher, did not know that it was not used in this older model. However, the order arrived quickly (4 days), and they are genuine Whirlpool, made in the USA, parts. The access to the sides of the dishwasher where the springs are attached...
Read more
More
$6.95
- Compare At:
-
$8.27
- You Save:
-
$1.32
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3379383
This replacement door spring maintains proper tension so the door opens smoothly and doesn't drop. Replace a weakened or broken spring to restore controlled, balanced door movement and everyday usability. What it does:
- Provides tension to balance the door's weight during opening and closing
- Helps prevent the door from slamming open or falling unexpectedly
- Common fix for a door that feels heavy, drops open quickly, or won't hold a mid-position
- Replaces springs that are stretched, fatigued, or broken
What's included:
Install notes:
- Disconnect power before servicing; springs are under tension—use gloves and eye protection
- Note the spring's routing and hook positions; take a photo before removal
- Use pliers to release and attach the spring carefully to avoid sudden release
- Some models use two springs; replace both for even tension if applicable
Do-It-Yourself Stories from Customers like You
Dishwasher door didn't work it felt like lifting dead weight Louis S. • Suffolk , VA • March 20, 2016
I ordered a pair of springs from AppliancePartsPros.com. When the new springs arrived, I unscrewed the frame from the counter top, slid the dishwasher out part of the way and installed the new springs and saved myself at least one-hundred dollars.
Read more
More
$21.95
- Compare At:
-
$25.90
- You Save:
-
$3.95
Genuine Whirlpool part
By: Whirlpool
Part Number: WP676453
Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679
Do-It-Yourself Stories from Customers like You
Tines on my dishwasher rack was rusting rust was showing on my dishes Jean M. • Lenoir , NC • January 10, 2015
Ordered dishwasher rack tine tips and bottle of vinyl touch up paint. I applied the paint to each tine and then placed the tips on the tines. I waited a few hours before using my dishwasher to allow the paint to dry and allow the tips to stick to the tines.
Read more
More
$30.95
- Compare At:
-
$37.14
- You Save:
-
$6.19
Genuine Whirlpool part
By: Whirlpool
Part Number: 675679
Color: White. Includes 125 caps used to cover damaged tips on your dishracks. For blue order 12022. For grey order 676458. To attach these tine tips you will need to order the dishrack white touch-up paint WP676453.
Do-It-Yourself Stories from Customers like You
Tines on my dishwasher rack was rusting rust was showing on my dishes Jean M. • Lenoir , NC • January 10, 2015
Ordered dishwasher rack tine tips and bottle of vinyl touch up paint. I applied the paint to each tine and then placed the tips on the tines. I waited a few hours before using my dishwasher to allow the paint to dry and allow the tips to stick to the tines.
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: 72032
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$17.76
- Compare At:
-
$21.13
- You Save:
-
$3.37
Genuine Whirlpool part
By: Whirlpool
Part Number: 8194582
includes seal
Do-It-Yourself Stories from Customers like You
Pump needed replacement cause nut that holds it on melted to the threads. Deborah S. • Lincoln , NE • November 06, 2017
Replaced nut and then found we needed new pump.
Read more
More
$52.33
- Compare At:
-
$62.80
- You Save:
-
$10.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3376397
Included with nut.
Do-It-Yourself Stories from Customers like You
Inadequate cleaning of dishes / detergent residue all over the interior Randy N. • Elkhart , IN • September 19, 2015
I cleaned all the jet nozzles with a toothpick and a pipe cleaner to remove the hard water deposits. I then replace the ring bearing under the bottom spray wand and the ring bearing under the upper spray wand. I also replaced the smaller radial ring bearing. Although none of them looked overly worn, it doesn't take much to cause the spray wands to spray inadequately.
Then, I replaced the float and washer assembly. Although it appeared to work properly when I lifted up on it and let it down, it...
Read more
More
$65.64
- Compare At:
-
$78.11
- You Save:
-
$12.47