Kenmore Dishwasher 665.17572202 (66517572202, 665 17572202) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W10795980
The Screw Hole Cap is an OEM part for Whirlpool dishwashers. It covers the screw holes, providing a clean and finished appearance while preventing moisture and debris from entering the screw openings. This helps maintain the dishwasher's aesthetic and ensures that screws remain protected from rust and corrosion.
Causes of a bad screw hole cap can include regular wear and tear, accidental impacts, or misplacement during maintenance.
Symptoms of a bad screw hole cap include:
- Missing or loose caps
- Moisture or debris accumulating in screw holes
- Visible wear or damage to the caps
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Screw hole plastic cap broke during installation Lori D. • Louisville , KY • March 28, 2017
I ordered the part and it was delivered the next day! Amazing experience!
Read more
More
$13.61
- Compare At:
-
$16.20
- You Save:
-
$2.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302868
Color: Black. Screw for lower toe panel. For Biscuit screw use 3400865, for white screw use WP3400836.
Do-It-Yourself Stories from Customers like You
Dishwasher door panel was rusting Prashant K. • Fishers , IN • October 11, 2014
I had no hope of separating the panel from the frame without damaging the frame since the two parts were rusted pretty badly and the screws holding the panel to the frame were completely beyond salvage. So I had to replace both the panel and the frame. I ended up removing the electrical/electronic connections, removing the panel/frame from the hinge and then replacing it with the new parts. Took about 90 minutes but the hardest part was removing other items from the rusting frame without...
Read more
More
$7.95
- Compare At:
-
$9.38
- You Save:
-
$1.43
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8580309
The Door Latch Strike is an OEM part for Whirlpool dishwashers. This part ensures that the dishwasher door securely latches when closed, maintaining a tight seal to prevent water leakage during the wash cycle.
Causes of a bad door latch strike include wear and tear from frequent opening and closing of the dishwasher door, accidental impact that can bend or break the strike, or buildup of debris that interferes with proper latching.
Symptoms of a bad door latch strike include:
- Dishwasher door not latching securely
- Water leaking from the door during operation
- Difficulty in closing or opening the dishwasher door
- The dishwasher not starting because the door isn’t properly closed
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Latch did not close properly causing dishwasher not to turn on and run Rani S. • Henrico , VA • March 24, 2020
I ordered this part and switched the previously used one.
Read more
More
$45.95
- Compare At:
-
$54.22
- You Save:
-
$8.27
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9743002
Gasket for upper wheel.
Do-It-Yourself Stories from Customers like You
2 broken "wheel and mount assemblies" (same side) and a few misc upper basket plastic part were broken Michael B. • Wellington , FL • December 29, 2015
With the basket out of the dishwasher, the plastic parts basically snap on and off... popped the broken parts off and the new parts on. The 2 wheel and mount assemblies were a little more complicated. The video on the website advises to disconnect the supply line and drain line... I didn't have to do this. I just pulled the dishwasher out of its cabinet a little over a foot and removed the 2 screws holding each assembly in place and removed them. The previous gaskets (2 PER ASSEMBLY)...
Read more
More
$9.95
- Compare At:
-
$11.84
- You Save:
-
$1.89
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268321
This replacement mount secures the dishwasher's upper spray assembly in place, keeping it aligned so it spins freely and delivers consistent water coverage to the upper rack for dependable cleaning performance.
- Holds the up-spray/upper spray arm assembly securely inside the tub
- Maintains proper alignment and clearance for free rotation
- Common symptoms: upper spray arm loose or falls off, poor cleaning on the top rack, rattling from the arm striking the rack or tub, visible cracks in the mount
- Restores stable support after a worn or broken mount
What's included: 1 upper spray arm mount. Install notes:
- Disconnect power and water supply before servicing
- Remove the upper rack for access; release the old mount and transfer the spray arm if attached
- Seat and lock the new mount; verify the upper spray arm spins freely
- Run a short test cycle to confirm proper operation
Do-It-Yourself Stories from Customers like You
Dishwasher: upper wash came off/broke Carl M. • Peoria , AZ • November 08, 2015
Replaced wash arm mount
Read more
More
$53.33
- Compare At:
-
$63.46
- You Save:
-
$10.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400919
This small decorative cap covers an exposed screw on your appliance, restoring a clean, finished look and helping prevent snags. Replace a missing or damaged cover to keep panels tidy and screws protected.
- Conceals screw heads on the cabinet, console, or panel for a neat appearance
- Helps protect hands and clothing from catching on exposed screws
- Replace if the original cover is missing, cracked, loose, or discolored
- Installs by pressing over the screw head where used to sit flush with the surface
What's included: 1 screw cover Installation notes:
- Disconnect power to the appliance; shut off gas or water if applicable before servicing
- Gently pry off the old cover using a plastic tool to avoid scratching finishes
- Align and press the new cover until seated flush
- Do not force; re-align if resistance is felt to prevent damage
Do-It-Yourself Stories from Customers like You
The water parts were broken the washer is about 16 years old Katrina M. • Fontana , CA • July 14, 2018
We bought replacement parts from you and my daughter fixed it. It is working now. It would have been nice if all the parts came in a set.
Read more
More
$6.95
- Compare At:
-
$8.34
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10177098
The Hex-Head Screw is an OEM replacement part for use in Whirlpool dishwashers. This metal screw measures approximately ¾ inch long. Its primary purpose is to secure the dispenser bracket in place, ensuring stable operation. This hex-head screw is designed for use with compatible hexagonal tools. This makes installation and removal straightforward. This part is sold individually and is guaranteed to fit your dishwasher door panel. This screw is compatible with select Whirlpool brand models including Amana, Crosley, Estate, Inglis, Jenn Air, Kenmore, Kitchen Aid, and Maytag.
Do-It-Yourself Stories from Customers like You
Dishwasher detergent dispenser Howard K. • Rockaway , NJ • November 01, 2015
Pulled a video from online and ordered my parts from Appliancepartspros.com. This was the second repair I've done with your help, the last being my washing machine. This time I replaced the dishwasher detergent dispenser on my Kitchen Aid. You guys make it so simple and give me the confidence to do it myself!
Read more
More
$10.41
- Compare At:
-
$12.28
- You Save:
-
$1.87
Genuine Whirlpool part
By: Whirlpool
Part Number: 4317824
The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.
Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.
Symptoms of a bad power cord include:
- The dishwasher not turning on or completing cycles
- Warm or hot power cords during operation
- Frayed, cracked, or exposed copper wiring
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Mice chewed the drain hose and power cord Noah C. • Eastsound , WA • February 16, 2015
Read directions on how to change the power cord and watched video on your site on how to change the drain hose. Everything went perfectly.
Read more
More
$20.95
- Compare At:
-
$24.93
- You Save:
-
$3.98
Genuine Whirlpool part
By: Whirlpool
Part Number: W10877094
This power cord connects your appliance to a household outlet. Replacing a worn or damaged cord restores safe, reliable power and can help resolve no-power or intermittent power issues caused by a compromised lead.
- Delivers electrical power from the outlet to the appliance
- Replaces cords with cracked, frayed, or heat-damaged insulation or a damaged plug
- Helps when the unit won't power on or loses power when the cord is moved
- Addresses visible scorching, arcing, or melting on the cord or plug
What's included: 1 power cord Install notes:
- Disconnect power before servicing; verify no voltage is present
- Note wire positions or take a photo before removal; match to the same terminals on install
- Use the proper strain relief/clamp and route away from sharp edges, moving parts, and heat sources
- Confirm the ground connection is secure; do not modify the plug
Do-It-Yourself Stories from Customers like You
Portable dishwasher was leaking at sink connection.The insulation was for an installed dishwasher. Carolyn C. • South Chesterfield , VA • May 06, 2023
Replaced the drain & fill lines on a portable dishwasher, now works prefect no leaks. Had to return the insulation blanket it would not fit under the counter for the built-in dishwasher.
Read more
More
$99.95
- Compare At:
-
$117.94
- You Save:
-
$17.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9741232
Quantity of ONE.
Size: 8-18 x 5/8 inch.
(#8 screw, 18 threads per inch, 5/8 inch long)
Do-It-Yourself Stories from Customers like You
My dishwasher was leaking out copious amounts of water while cycling Michael K. • Oakland , MI • July 11, 2019
While at my sister's house, she showed me how to access & dismantle the housing unit on her dishwasher, thinking the issue might be from that area. So, when I came home, I opened up my housing unit and found that several of the screws had come out and the pump outlet seal was stretched out and partially outside of the unit itself. I located all of the missing screws & discovered I was still missing one, which my husband helped me order with the pump outlet seal. I easily replaced the old seal...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10348409
This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.
- Provides threaded fastening for panels, brackets, covers, or internal components
- Replaces worn, rusted, stripped, or missing hardware
- Helps reduce vibration and rattling from loose parts
- Restores proper alignment and a secure fit of attached parts
What's included: Includes 1 screw. Installation notes:
- Disconnect power; turn off water supply before service
- Note original screw location and retain any spacers or clips for reassembly
- Start threads by hand to avoid cross-threading
- Tighten snugly; do not overtighten to prevent stripping
Do-It-Yourself Stories from Customers like You
Dishwasher would not start Mark M. • Midlothian , VA • July 16, 2016
Maytag Dishwasher (about 5 years old). Some of the buttons had stopped functioning. Then the Start button began choosing whether or not to work. Eventually it would not start at all. Upon removing the control panel, the first thing I noticed was that the brackets that hold the two lower screws were broken. (So this was the reason that the door was so hard to open from the time it was new.) I trouble shot the thermal fuse, the door-latch switches, and inspected the control board trying to find...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10358302
Goes from pump to exterior drain hose.
Do-It-Yourself Stories from Customers like You
Dishwashwer was only partially draining James M. • Barre , MA • November 07, 2016
I figured out that it was probably a plugged pump hose, since the pump would run, it somtimes it drained and sometimes it didn't. Your video helped with how to take the dishwasher out and replace the hose. I replaced the hose and everything is now working fine. It turned out to be a broken check valve in the old hose that caused the problem. It took 90 mins to do the repair.
Read more
More
$52.95
- Compare At:
-
$62.48
- You Save:
-
$9.53
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268909
Overfill control.
Do-It-Yourself Stories from Customers like You
Washer would not fill with water Ty J. • Hillsboro , OR • July 08, 2018
Replaced float switch and also replaced intake valve. Worked like a charm and the process was as easy as the YouTube video I followed made it seem.
Read more
More
$45.95
- Compare At:
-
$54.22
- You Save:
-
$8.27
Genuine Whirlpool part
By: Whirlpool
Part Number: W11631670
This factory-specified screw secures panels, brackets, and internal components in your appliance. Replacing worn or missing hardware restores a tight fit to help reduce vibration, noise, and premature wear.
- Fastens sheet metal, brackets, or plastic parts as designed by the manufacturer
- Helps maintain alignment and reduce vibration/rattling
- Direct replacement for stripped, corroded, or missing screws
- Common signs: loose panels or trim, shifting components, screw won't tighten
What's included: One screw Install notes:
- Disconnect power; shut off water or gas supply if applicable
- Use the correct driver to avoid stripping the head
- Start threads by hand to prevent cross-threading; tighten snugly without overtightening
- Replace one-for-one in the original location per service information
Do-It-Yourself Stories from Customers like You
Some accessories were worn. Wayne C. • Massapeqau Park , NY • April 15, 2020
My son fixed the issue of some wear and tear.
Read more
More
$9.95
- Compare At:
-
$11.84
- You Save:
-
$1.89
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8531857
This inlet protector is the coarse screen that covers the dishwasher's pump/sump inlet, blocking large debris from entering the wash system. Replacing a damaged or missing protector helps maintain water flow and protect the pump from jams or wear.
- Screens large food particles and debris from the pump/chopper inlet
- Helps maintain proper water circulation and consistent cleaning performance
- Reduces risk of pump damage or noisy operation from debris
- Common signs: cracked or missing screen, persistent debris in the sump, grinding/rumbling noises, or declining wash results
What's included: 1 inlet protector Install notes:
- Disconnect power and shut off water supply before servicing
- Remove the lower rack and spray arm; access the sump/accumulator area per your model
- Lift out the old protector; seat the new protector fully and secure any tabs/fasteners
- Reassemble and ensure the screen sits flat with no gaps
Do-It-Yourself Stories from Customers like You
Clogged at the chopper assembly strange noisehopper assembly broken Thomas H. • Idaho Falls , ID • July 07, 2015
Looked at Dishwasher. Scratched head and armpit. Told wife I would fix, not repariman. Wife skeptical - shook head. Found schematic on web. Found YouTube video of guy repairing same DW model. Disassembled. Diagnosed problem. Chopper assembly welded in place by water scale -broke removing. Potty mouth. Ordered parts. Waited for parts. Washed dishes by hand. Wife doing ok. Parts arrived (in only a day or two!!! Fed Ex for 7 bucks!! Great deal). Put on nasty t-shirt, baggy shorts. ...
Read more
More
$78.57
- Compare At:
-
$94.74
- You Save:
-
$16.17
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10477552
This heater terminal nut fastens the heating element's electrical connector to its stud, keeping the connection tight under heat and vibration. Replacing a worn or missing nut restores safe contact and consistent heating performance.
- Secures the wire/ring terminal to the heater stud for a solid electrical connection
- Helps prevent arcing, discoloration, and heat damage from a loose connection
- Signs include a loose terminal, burnt odor, or melted/charred insulation at the heater connection
What's included: 1 heater terminal nut
- Disconnect power and allow the appliance and element to cool completely before service
- Photograph wiring for reference; remove old hardware and clean the terminal
- Inspect the ring terminal, insulators, and stud; replace any heat-damaged components
- Start threads by hand to avoid cross-threading; snug with the correct nut driver—do not overtighten
Do-It-Yourself Stories from Customers like You
Stopped running after rinse cycle and the clean light was flashed 3 times Clyde Y. • Turtle Creek , PA • August 29, 2015
Replaced the heating element as shown in the video. Repaired a bad connector on the wire leading to the heating element. The clean light still flashed 3 times. Determined that the thermal fuse also needed to be replaced. Replaced the thermal fuse as shown in the video. The clean light now flashed 7 times which I discovered meant that the control panel needed to be reset. I then reset the control panel by pressing the buttons: normal, heated dry, normal, heated dry. It now works perfectly.
Read more
More
$9.95
- Compare At:
-
$11.84
- You Save:
-
$1.89