Kenmore Dryer 796.69278900 (79669278900, 796 69278900) Parts

• No heat or not enough heat
• Won't start

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

I consulted with the internet and your website and determined I had a bad roller wheel. I was going to buy just one but determined if you have to take the thing apart, just replace all of them. These lasted 10 years after all. Opened up You Tube for the method to take the dryer apart. After doing the washer last year, I felt pretty bold and just ripped into the project. Within 30 minutes I had the drum out and located the problem wheel ( rear right side). It was locked up due to hair build up... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

• Takes too long to dry

After I cleaned out the typical 1.5 pounds of lint from the vent, ( I do it every 2 months), I went searching for a solution. I found 6 possible causes on this site and purchased everything except a new burner; I wasn't going to go that far. Let the fun begin. Since my vacuum was still nearby, I thought I was ready for anything. Wrong. After I watched all the videos again for reassurance, I went in with screwdriver in hand and laptop nearby. I removed the top and looked inside. Don't be fooled,... Read more

Was going to order 4 new wheel & spindle sets, then saw you could get just the wheel for 1/3 the cost, so I ordered those. Then in the frequently ordered other items I saw the idler wheel assy. So I ordered one of those also. Glad I did, it was in worse shape than any of the wheels which still seemed to spin freely after I got all the hairs and crap off them. Anyways, went by the video step by step. Pretty straightforward. Have a good vacuum handy, I’m surprised that it used to dry at all... Read more

I purchased a new replacement. Read more

After reading several stories online about what to replace to fix the issue with my dryer not completely drying my clothes I decided to purchase a heating assembly, a sensor and a thermistor. I am not sure which one of these three pieces corrected the issue, but my dryer is back to drying my clothes as it should. The Youtube video's are priceless in helping to find and replace the parts. Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

From reading "troubleshooting" sites on the internet, originally thought I'd be replacing the front & rear drum rollers, so I ordered the rollers, and a new belt before I opened up the dryer, taking it out of use. When I opened it up the front rollers were "shot", and the front bulkhead was "totaled". Waited for parts to arrive (within 2 days), and successfully replaced front & rear rollers, bulkhead, drum seal. The on-line videos really helped me ensure I was keeping in the right order. My... Read more

I have order three parts, guide filter, cover guide, and sensor assembly. My previous cover guide was from two parts, when sensor assembly was one of them. New part ( guide cover ) was all in one piece so I just transfer old metal part of sensor to new cover guide and I don't need that sensor assembly anymore. I have ordered all three parts overnight by Fedex, ordered 15 min before 5pm, so next day it was here. Dryer is fixed, I'm happy. Read more

I have an LG dryer purchased in 2007. Model: DLE9577SM. It was squeaking at start-up and rumbling a little. Not knowing what parts I would actually need, I ordered rollers with/without assemblies, tensioner pulley-only, new belt. After viewing this video a couple of times, I attacked my machine which is located in the comfort of my garage. Lots of room to spread out. Nice. This disassembly went OK however because, I suspect, my machine is 13 years old, the removal of the control panel was... Read more

Bought a new switch assembly, watched the video, and replaced the switch. Thr dryer now runs fine. Replacement part matched esxactly. Read more

This was a pretty simple install if you know how to take apart your dryer. I have a kenmore dryer which is identical to an LG dryer. My kenmore dryer was actually made by LG at that time. You can find the specific model on youtube and see how your dryer comes apart. While doing this i cleaned all the inner parts of my dryer. The parts that come in the kit can be bought at home depot for much less but you don't know what length you need. I ordered the kit so I could have the back plate and... Read more

If your LG Front load washers sounds like a freight train, STOP USING IT. You're doing more damage and will need more parts to fix it. After the noise became unbearable, I began to explore and disassemble. I knew enough to know the bearings must be bad but had never done this repair before. ( I am however pretty mechanically inclined.) Watch this video before you start tearing your LG apart. APP did a great job explaining the steps of the repair. Do a search on this site or youtube.com with... Read more

I spoke with the experts at parts pro and they suspected the main power board. I ordered the main power board along with the control panel. Since I was taking everything apart I decided to replace other components as well- thermostats, thermistor , sensor wire. When I was all done the old LG was back to working like new. Oh while I was at it I cleaned and vacuumed out the complete machine. Great factory parts, videos p, service and videos, the price of all the parts was less than a repair... Read more

• Too hot
• Doesn't shut off
• Takes too long to dry

I replaced the dryer motor. I followed the repair video on the Appliance Parts Pro site, with a few modifications to the procedure. I loosened the control panel and flipped it forward to improve access to the wiring connectors. I also loosened the front panel and tipped it forward before disconnecting the door switch as there wasn't enough space to disconnect the switch otherwise. Removal of the blower assembly required the use of penetrating lubricant as the assembly was stuck on the motor... Read more