Lg Washer Dryer Combo 31412 Parts

This clutch housing assembly supports the clutch coupling in the washer's drive system, aligning and securing moving components that shift between wash and spin. Replacing a worn housing restores smooth engagement and consistent agitation and spin performance. What it does:

• Houses and supports the clutch coupling that engages the basket for wash and spin cycles
• Maintains alignment of drive components to help prevent slippage and noise
• Helps transfer motor power to the wash plate/basket through the clutch mechanism
• Common symptoms of a failing part: no or intermittent spin, weak/no agitation, grinding or scraping noises from the bottom of the washer

• One clutch housing assembly

• Disconnect power and water; turn off supply valves before servicing
• Access is typically from the bottom—tilt or lay the washer carefully and support it securely
• Remove rotor/stator and clutch components as needed to reach the housing; note fastener locations and wiring
• After reassembly, rotate the drive by hand to check for binding and run a test cycle to verify agitation and spin

Washer won't spin or agitate? This rotor assembly forms the rotating half of the direct-drive motor, restoring basket movement when worn or stripped.

Banging or excessive vibration during spin? A worn suspension assembly causes loud noise and out-of-balance errors. Simple DIY fix with just a screwdriver.

Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.

Fix detergent leaks or dispenser jams with this washer detergent housing assembly. Routes detergent properly and replaces cracked or warped housings.

This is a friction oil damper that mounts on the lid hinge of a top-load washing machine. It controls the speed at which the lid opens and closes, preventing it from slamming shut or swinging open too quickly. Replace this part if the washer lid drops down forcefully, no longer stays open on its own, or if the existing damper is leaking oil.

Fix detergent not dispensing or residue buildup. This washer dispenser assembly releases detergent and fabric softener at the right time during cycles.

Genuine hardware washer that distributes fastener load at assembly joints. Replace if worn, cracked, or causing loose connections. Confirm fit with your model.

Replacement nut that secures drawer and trim components on compatible LG appliances. It restores a firm, vibration-resistant fastening to help prevent loosening, rattling, or misalignment during normal use. What it does:

• Secures drawer, trim or small mounting brackets to the appliance chassis.
• Helps stop loosened fasteners that cause rattling or misaligned panels.
• Provides proper thread engagement for a stable connection.
• Matches the appliance's original fastening point when used as the listed part.

• Always disconnect power to the appliance before beginning any repair.
• Use the correct-size wrench or socket; avoid overtightening to prevent stripped threads.
• Inspect mating screw/bolt and threads for damage; replace damaged hardware as needed.

Leaking water behind your washer? A cracked inlet hose is often the culprit. This hose channels water from your supply line into the machine during fill.

This replacement nut secures bolts or studs in your appliance. Replacing a missing or stripped nut restores a tight, reliable connection to keep brackets and assemblies stable and reduce vibration or rattling. What it does:

• Provides threaded retention for bolts/studs on panels, brackets, and assemblies
• Helps maintain alignment and stability during operation
• Typical failure signs: stripped threads, missing hardware, loose or rattling components, vibration
• Direct replacement for the original nut in the same location

• 1 nut

• Disconnect power before service; shut off the water supply
• Match thread size/pitch to the original; start threads by hand to avoid cross-threading
• Tighten with the correct tool; do not overtighten or damage mating parts
• Reinstall any washers/spacers in the original order and verify secure fit

Suppresses electrical interference on your washer's AC power line to protect control boards. Replace if washer won't power on, stops mid-cycle, or controls malfunction. Verify fit by model number.

Small metal washer used in washer internal mounting assemblies. Provides proper spacing between components and secures fasteners. Replace if worn or missing.

Replacement mounting bracket holder that secures internal washer components. Needed when your original bracket is cracked, broken, or missing.

Tapping screw secures washer panels, brackets, and trim in place. Replace stripped, rusted, or missing screws to restore proper fit and stability.

Kit is no longer available. Order MCJ61861201 and ACP72929002 separately.