Lg Washer Dryer Combo 31522 Parts

Fix dispenser overflow or leaking issues with this washer detergent drawer assembly. Channels water through detergent and softener compartments. DIY repair.

Hardware washer that sits beneath screws or nuts to distribute load and secure fasteners. Replace if bent, missing, or worn to restore proper fit.

This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.

• Directs incoming water from the fill valve to the dispenser/tub during wash cycles
• Maintains a sealed path to prevent internal or external leaks
• Helps the washer reach proper fill levels and timing
• Common symptoms of failure: water on the floor, leaks during fill, visible cracks or bulges, long/no fill or IE error

• Unplug the washer and turn off both hot and cold water supplies
• Keep towels or a pan handy; relieve residual water pressure before disconnecting
• Note the original routing; fully seat the hose on fittings and secure with existing clamps
• Restore water and power, then run a quick fill to check for leaks

This customized screw secures factory components in compatible LG appliances. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit so panels, brackets, or assemblies stay properly aligned and safely mounted.

• Fastens a designated component per model design
• Maintains alignment and helps reduce vibration/noise
• Replaces missing, stripped, or corroded hardware
• Common signs: loose or rattling panels, misalignment, or an obviously missing screw

• Disconnect power to the appliance; shut off water or gas if applicable
• Use the correct driver size; support the part being secured
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• Transfer any washers, spacers, or caps from the original fastener if required

This clutch housing assembly supports the clutch coupling in the washer's drive system, aligning and securing moving components that shift between wash and spin. Replacing a worn housing restores smooth engagement and consistent agitation and spin performance. What it does:

• Houses and supports the clutch coupling that engages the basket for wash and spin cycles
• Maintains alignment of drive components to help prevent slippage and noise
• Helps transfer motor power to the wash plate/basket through the clutch mechanism
• Common symptoms of a failing part: no or intermittent spin, weak/no agitation, grinding or scraping noises from the bottom of the washer

• One clutch housing assembly

• Disconnect power and water; turn off supply valves before servicing
• Access is typically from the bottom—tilt or lay the washer carefully and support it securely
• Remove rotor/stator and clutch components as needed to reach the housing; note fastener locations and wiring
• After reassembly, rotate the drive by hand to check for binding and run a test cycle to verify agitation and spin

Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.

Washer won't spin or agitate properly? A worn stator disrupts the motor's magnetic field, preventing drum rotation. Moderate DIY repair restores spin.

Fix detergent leaks or dispenser jams with this washer detergent housing assembly. Routes detergent properly and replaces cracked or warped housings.

Fix detergent not dispensing or residue buildup. This washer dispenser assembly releases detergent and fabric softener at the right time during cycles.

Genuine hardware washer that distributes fastener load at assembly joints. Replace if worn, cracked, or causing loose connections. Confirm fit with your model.

Replacement nut that secures drawer and trim components on compatible LG appliances. It restores a firm, vibration-resistant fastening to help prevent loosening, rattling, or misalignment during normal use. What it does:

• Secures drawer, trim or small mounting brackets to the appliance chassis.
• Helps stop loosened fasteners that cause rattling or misaligned panels.
• Provides proper thread engagement for a stable connection.
• Matches the appliance's original fastening point when used as the listed part.

• Always disconnect power to the appliance before beginning any repair.
• Use the correct-size wrench or socket; avoid overtightening to prevent stripped threads.
• Inspect mating screw/bolt and threads for damage; replace damaged hardware as needed.

Replace a cracked or clogged washer nozzle assembly to restore proper water flow and prevent poor cleaning performance. Moderate DIY repair.

Adjustable leveling leg that supports your washer and allows height adjustment. Replace if damaged, stripped, or missing to restore stability on uneven floors.

This replacement nut secures bolts or studs in your appliance. Replacing a missing or stripped nut restores a tight, reliable connection to keep brackets and assemblies stable and reduce vibration or rattling. What it does:

• Provides threaded retention for bolts/studs on panels, brackets, and assemblies
• Helps maintain alignment and stability during operation
• Typical failure signs: stripped threads, missing hardware, loose or rattling components, vibration
• Direct replacement for the original nut in the same location

• 1 nut

• Disconnect power before service; shut off the water supply
• Match thread size/pitch to the original; start threads by hand to avoid cross-threading
• Tighten with the correct tool; do not overtighten or damage mating parts
• Reinstall any washers/spacers in the original order and verify secure fit

Replaces a cracked, rusted, or damaged tub cover assembly that attaches to the outer tub rim. Prevents water leaks and splashing during wash cycles.

Leaking water behind your washer? A cracked inlet hose is often the culprit. This hose channels water from your supply line into the machine during fill.