Need Help?
Call
Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.
With the video that was made from appliance pro.Help me out one hundred percent to understand what I was dealing with Read more
Washer won't drain or shows OE error? This drain pump assembly removes water during spin cycle. Moderate DIY repair with video guide available.
It was fairly obvious that the washer drainer motor had failed, water was not draining, filter was clean (bottom lower left panel door, have a pail ready!) and drain line was not blocked. Someone had provided great advice on the Appliance Parts Pro's site about replacing the drain motor from the bottom. Great suggestion! Easy to do, although be prepared for more water to drain from the washing machine onto the floor after you lay it over. I carefully lowered the machine onto it's back,... Read more
Fix washer IE error or no water flow issues with this water inlet valve. Controls hot or cold water flow into wash drum. 15-minute DIY repair.
Replaced the cold water valve unit (has 4 ports and 1 inlet) which is very straight forward; requires : 1 phillips screwdriver ~#2 1 needlenose plier, medium size 1 channel lock plier, medium size 1 marker pen 1 - cold water valve assembly # AP4445613 1 - hot water valve assembly #AP4441935 1 - water level pressure switch #AP4440713 an old towel or two for absorbing small amounts of water a cellphone / camera for making sure you have the... Read more
This three coil solenoid is used for the cold water, bleach dispenser and prewash.
1. I unplugged the washer from outlet 2. I turned off the hot and cold water taps going to the washer (both just in case) 3. Draped a towel over back edge of washer and under where hoses coming from water outlets attach to back of washer (to catch any loose water out of the hose or screw nozzle leading to valve assembly, then unscrew (by hand) the cold water hose from back of washer (leave hot water hose alone as not needed). 4. Unscrew valve assembly from washer by two screws on back top of... Read more
Replace your washer door boot seal to stop leaks between the door and tub. Install when you notice water escaping or visible tears. Verify fit by model.
I called an appliance repair company. They use a flat rate billing system which I don't like. They told me it will cost around $250.00 to replace the gasket and I would have to move my machine out so he would have room to repair it. He said the part would be in in 5 days. I found you on line, ordered the part for around $69.00 and to my delight there was a video on how the repairs should be done. The video was very professionally done and I watched it twice just to memorize the procedure. ... Read more
Replacement tub to pump hose for washers. Transports water from the wash tub to the drain pump. Replace if cracked, split, leaking, or damaged from wear.
First and foremost, much thanks to APP for perfect transaction, and incredible price! The part was shipped quickly, and arrived fast. Immediate Availability of the part was outstanding, and truly saved this Canadian's day! See, in Canada, LG has their own unfair practice of NOT ALLOWING a Canadian citizen to purchase ANY functional parts for any of their appliances or products... furthermore, in order to get the part for any issue, you must pay directly for an LG direct service tech to come at... Read more
Connects detergent dispenser to washer tub. Replace if cracked, leaking, or clogged with detergent buildup. Verify fit with your model number.
****** always make sure the unit is fully unplugged from the power before you do anything with the outside of the unit to work inside of the unit and while you are working inside the unit... Also make sure that you turn the hot and cold water intake valves off and make sure you don't pull too much on the two water intake hoses that lead to your washer because they can leak with too much pressure exerted on either end******* 1. Took top off unit by unscrewing mounting brackets at two similar... Read more
Washer not filling or overfilling? This water level pressure switch monitors water levels and signals when to stop filling. Easy 10-minute DIY repair.
The LG Model LG Washer model WM2487HRMA ISSUE: Washing Machine was filling very slowly. Overnight it would fill about 1 or 2 gallons. I would clear the tub by pushing a) Power b) set spin to None c) push Start. That would empty the tub. REPAIR SOLUTION: That did not solve the problem. Second, I replaced both the single (1) Water inlet valve assembly Part Number:5220FR2006H and also the Water Level pressure switch Part Number:6601ER1006E That solved the problem. I can't tell you which... Read more
Fix detergent not dispensing or a broken dispenser drawer. This washer detergent box assembly holds and releases soap properly. DIY-friendly repair.
I replaced the dispenser assembly and since this was being replaced, I installed a new drawer and detergent box assembly. Read more
Washer won't spin or shows LE error code? The stator assembly converts power to spin the drum. Moderate repair, typically takes 30-60 minutes with video.
Swapped bad part for new part. Read more
The Vent Hose is an OEM part for LG washing machines. This hose is essential for ensuring proper ventilation within the washer, allowing air to circulate and preventing the buildup of moisture and mildew. It helps maintain the efficiency of the washing machine by facilitating the expulsion of air and excess water vapor during operation.
Causes of a bad washer vent hose can include wear and tear over time, blockages from lint or debris, or damage due to bending or pinching.
Symptoms of a bad vent hose include:
This OEM LG part is also compatible with Sears/Kenmore.
Removed the top cover while the machine was operating, located the source of the leak. The top filler tube had worn a hole in a flex point. Found the right part on this site, replaced it with little effort. While in there I saw a similar hose and decided to replace it as its time was probably up too. So far so good, washing clothes and no leaks!! Great prices and best of all the right parts were delivered in a timely manner. Thanks for making this so easy. Only specialty tool used was hose... Read more
Includes sensor probe
Usually ships within 4 - 14 days
Supports the washer drum for smooth, quiet spinning. Replace if you hear grinding noises or excessive vibration during cycles. Confirm fit with your model.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.