Lg Washer WD-10271BD Parts
Genuine Lg part
By: Lg
Part Number: 4986ER0004B
Seals washer door to prevent leaks during cycles. Replace if worn, torn, or leaking. Verify your model and existing gasket drain hole configuration.
Do-It-Yourself Stories from Customers like You
Slow leak from front of LG Tromm washing machine. Peter M. • Norwood , MA • February 26, 2022
I had a slow leak from the very front of my LG washer, so I was pretty sure that it was just the gasket leaking, and not any of the hoses. It's not a complicated repair, with the usual confidence-inspiring video from Matt. There are three things to be aware of:
1) I originally ordered the wrong gasket. My model number is WM2277HW /01, which the APP website does not recognize. It only recognizes /00 or no suffix whatsoever. The correct part number for the /01 is 4986ER0004B. The easy way...
Read more
More
$127.65
- Compare At:
-
$150.63
- You Save:
-
$22.98
Genuine Lg part
By: Lg
Part Number: 4866ER0004A
Concrete balance weight mounts to washer outer tub to stabilize drum during spin. Replace if cracked, broken, or missing to restore proper vibration control.
Do-It-Yourself Stories from Customers like You
Loud banging and imbalance during spin cycle Robert V. • Las Vegas , NV • January 03, 2016
My problem was a broken spider. I followed your excellent video, but have some additional input that should be incorporated in a new video showing the required upgrade procedures and parts required to repair an early model with damaged front tub half using currently available parts. Don't expect everything to go as easy as the video. 1) Used 4lb. brass hammer to drive shaft from bearings. 2) Torqued spider bolts to 20ft lbs. with thread locking compound. 3) attached rubber seal to front tub...
Read more
More
$83.77
- Compare At:
-
$99.69
- You Save:
-
$15.92
Genuine Lg part
By: Lg
Part Number: 4036FR4050A
Seals the temperature sensor where it passes through the washer tub. Replace if worn or leaking to prevent water damage. Confirm fit with your model.
Do-It-Yourself Stories from Customers like You
Worn out bearings Linda B. • San Diego , CA • November 23, 2015
After watching the video carefully and taking notes for step-by-step dismantling of the LG washer, I took it apart methodically placing each item on a table in the order removed. I was able to remove and replace the bearings with no problems following the tips and tricks. The spider did not seem to be in bad shape but since I had a new one, it seemed reasonable to replace it as well, but it was difficult to extract the old one from the drum. The bolts are assembled with weld glue, so it is a...
Read more
More
$12.47
- Compare At:
-
$14.84
- You Save:
-
$2.37
Genuine Lg part
By: Lg
Part Number: 4011FA4353B
Secures the stator to the motor assembly in your washer. Replace if bolt is stripped, spinning freely, or missing to restore proper motor stability.
Do-It-Yourself Stories from Customers like You
The washer sounded like a jet plane when it went through the spin cycle very loud noise Lane C. • Pleasant Garden , NC • February 24, 2015
I originally thought the washer had a bad bearing, but once I got it disassembled it the spider arms were broken. This required the replacement of the tub assembly. While replacing the tub I replaced all of the water bellows. The parts came quickly, the live chat and videos were very helpful. This washer has to be completely disassembled to replace the drum, so mark all the screw locations, tag and bag everything and take lots of pics. It was a very rewarding project and hundreds of dollars...
Read more
More
$11.60
- Compare At:
-
$13.80
- You Save:
-
$2.20
Genuine Lg part
By: Lg
Part Number: 4860FR3092C
Secures washer hoses to pumps, tubs, and drain fittings to prevent leaks. Replace when weakened, rusty, or damaged to maintain tight connections.
Do-It-Yourself Stories from Customers like You
Loud noise during spin cycle Steven S. • Celina , OH • March 10, 2019
I started by watching the video and it was very helpful. I would make one suggestion. On our model the weights on the tub sit very close to the front gasket. It is much easier to put the gasket on the tub before you put the weights on. Also, since the washer was tore apart, I replaced the hoses and seals and shocks since the machine is about 8 years old. The shocks made a huge difference. It spins like it did when it was new. Thanks for the video, it was very helpful.
Read more
More
$17.95
- Compare At:
-
$21.36
- You Save:
-
$3.41
Genuine Lg part
By: Lg
Part Number: 1SZZER4002A
This Screw (drawing) is a factory fastener used to secure appliance panels and components. Replacing a stripped, corroded, or missing screw restores a tight fit, reduces vibration, and helps keep assemblies correctly aligned.
- Secures panels, brackets, and mounting points as specified by the manufacturer
- Replaces screws that are lost, damaged, corroded, or stripped
- Helps address rattling, vibration, or loose-fitting parts caused by missing hardware
- Maintains proper alignment and stability of the assembly
What's included: One screw
- Disconnect power and, if applicable, shut off gas/water before servicing
- Match the screw to its original location; start threads by hand to avoid cross-threading
- Use the correct driver; tighten snugly without over-torquing into metal or plastic
- Refer to your model's parts diagram to correct location and quantity
Do-It-Yourself Stories from Customers like You
Lg washer/dryer combo unit shook upper counter balance weight loose damaging the mount lugs on the tub cover and tore the tub gasket Christine V. • Saluda , VA • March 28, 2020
The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back...
Read more
More
$10.70
- Compare At:
-
$11.77
- You Save:
-
$1.07
Genuine Lg part
By: Lg
Part Number: 6411ER1006V
Replaces a frayed, melted, or damaged power cord on your washer. Restores grounded connection from wall outlet to internal power circuit.
More
$64.95
- Compare At:
-
$76.64
- You Save:
-
$11.69
Genuine Lg part
By: Lg
Part Number: MEJ62305102
Channels household water to your washer's fill system. Replace if cracked, leaking, or worn to restore proper flow and prevent water damage to floors.
Do-It-Yourself Stories from Customers like You
Broken part William W. • Oak Ridge , NJ • January 29, 2016
Replaced
Read more
More
$26.72
- Compare At:
-
$31.53
- You Save:
-
$4.81
Genuine Lg part
By: Lg
Part Number: 4860FR3092D
Secures hose connections to prevent leaks in your washer. Replace if corroded, rusted, or leaking around hose fittings. Confirm fit by model number.
Do-It-Yourself Stories from Customers like You
Broken hose Mark W. • Gilbert , AZ • November 26, 2018
Replacement
Read more
More
$11.95
- Compare At:
-
$14.22
- You Save:
-
$2.27
Genuine Lg part
By: Lg
Part Number: 4810ER3021A
Mounts the door hinge to your washer's front cabinet. Replace if bracket is bent, broken, or missing to restore proper door alignment and sealing.
Do-It-Yourself Stories from Customers like You
Door was missing when we bought the washer Charles K. • Yulee , FL • December 22, 2015
The dealer gave us a door but it didn't fit. Everything we bought from Appliance Parts Pros.com was fixed with just a screwdriver. Easy and fast. Shipping was fast also. The longest time was installing the hinges on a stacked washer and dryer.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Lg part
By: Lg
Part Number: 5215FD3715L
This rubber fill hose connects the household hot water supply valve to the washing machine's water inlet valve. It delivers hot water into the wash tub during the fill cycle. Replace this hose if it is cracked, leaking, bulging, or showing signs of deterioration to prevent water damage.
More
$44.95
- Compare At:
-
$53.49
- You Save:
-
$8.54
Genuine Lg part
By: Lg
Part Number: 4810ER3016A
Mounts to the washer's lower frame to secure components and maintain alignment. Replace if bracket is cracked, broken, rusted, or missing hardware.
Do-It-Yourself Stories from Customers like You
Rusty corroded parts. J D. • Crestview , FL • January 26, 2021
Replaced leg mount and leg.
Read more
More
$19.48
- Compare At:
-
$23.38
- You Save:
-
$3.90
Genuine Lg part
By: Lg
Part Number: 4941ER3005D
This replacement knob assembly restores tactile control for a range or cooktop control. It provides a secure grip and clear detent positions so you can set burner or surface settings reliably. What it does:
- Replaces a worn, cracked, or missing control knob to regain safe, predictable control
- Engages the shaft and detents so settings stay put during use
- Helps eliminate slipping or difficulty turning the control
- Matches original fit and function for direct replacement
What's included:
- One knob assembly as shown
Install notes:
- Turn power/gas to the appliance off before servicing; follow appliance manufacturer safety instructions
- Remove the old knob by pulling straight off the control shaft; press the new knob onto the shaft until it seats
- Wear work gloves to protect hands from sharp edges during access
Do-It-Yourself Stories from Customers like You
The knob. Kebreab G. • Nashville , TN • January 14, 2021
I ordered a knob
Read more
More
$84.95
- Compare At:
-
$101.09
- You Save:
-
$16.14
Genuine Lg part
By: Lg
Part Number: 3550ER1032A
Protective access cover shields internal washer components from dirt and moisture. Replace if cracked, broken, or missing to restore factory protection.
More
$31.95
- Compare At:
-
$37.70
- You Save:
-
$5.75
Genuine Lg part
By: Lg
Part Number: 3212ER0005A
Outer door frame for front-load washers. Plastic housing that surrounds the door glass. Replace if cracked, broken, or damaged from impact.
More
$310.34
- Compare At:
-
$354.41
- You Save:
-
$44.07
Genuine Lg part
By: Lg
Part Number: AEJ33026401
A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does
- Provides a secure mounting point for internal parts that rely on a fixed support
- Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
- Helps restore correct component positioning to improve part interaction and operation
- Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly
What's included
Install notes
- Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
- Basic hand tools typically required; handle clips and tabs gently to avoid damage
- Inspect adjacent components for wear and replace if needed for a long-lasting repair
More
$7.52
- Compare At:
-
$8.87
- You Save:
-
$1.35