Samsung Washer Dryer Combo WD15F5K5ASG Parts

I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more

• Noisy
• Leaks water

Replaced drain pump. Your video on your web site was very helpful. Read more

Ordered new control knob and replaced broken one. The most difficult part was popping out the control panel so I could access the control knob. I ended up "wrestling" it out. It would be wonderful if the product manual had some guidance on how to pop out all panels. Read more

I took apart the washer to find both of the weight balancers had broken in 2 and were banging around. They had also caused the boot seal to rip. I removed the broken weight balancers and replaced them along with a new boot seal. There was one small spot with the seal wasn't fully attached to the outer drum so I had to take it back apart to fix that minor error on my part. Otherwise, it was a fairly easy fix. Read more

I watched the you tube video that completely explained how to do it. It was very easy to do. Read more

• Door latch failure

I removed the wire and rubber seal in order to get to the door lacth then I unscrewed the three screws popped out the latch put the screws and the rubber and wire back and tested the washer. The door now locks and I can wash again...YEPPPPY Read more

First indication something was wrong when the washing drum starting to violently bang against the inside of the washer while in spin cycle. Then, when I opened the washer door, a misty smoke came from the inside. With the video from Appliance Parts Pros, disassembly of the washer was no problem. First, I replaced the four shocks on the washer drum. But, after a test run, determined that it was spider arm assembly. Again, the series of instructions made getting to the part fairly easy. The... Read more

Ordered a new knob and took out little bits of the old one. Took the new knob and pressed it over the stump and presto works like new. Read more

I replaced the main PCB in the back bottom of the washer. Simple exchange of pcb. All I needed was a phillips screwdriver and a second set of hands while all the cabling was moved from the original main pcb to the replacement pcb. Washer works like a charm now. Read more

Followed the excellent videos provided by AppliancePartsPros. Made a multi step repair, if not simple, then extremely less complicated. Loved the way they showed the step by step disassembly as well as the step by step reassembly. Great videos. Got the right parts the first time and very fast delivery. Can’t say enough good things about AppliancePartsPros.com Read more

I first check the schematics to find the heat sensor. On my model it's c on the control panel. I checked the continuity on the orange and white wires. It showed some continuity but not much. I then went to the heater element and found the orange and white wires going to the thermistor. Turns out the heater element and thermistor need repalced. Read more

Removed top panel to reach the hose and sensor. Propped the washer back, reached up to remove bottom hose assembly. Replaced with new hose and new sensor. Put top panel back on. Parts place told me the part was backordered for months and repair would cost at least $80. Got it in three days and fixed it myself. Read more

When I opened the rear cover and check the temperature sensor, I noticed the wire connection was damp. I dried it up with a hair dryer and it worked again for a few days. Then the problem came back. When I gone back to inspect the second time, i noticed a lot of water on the floor. I knew there was a leak. I followed the disassemble samsung washer video from "Repair clinic.com" to open the top cover, then i realized the assembly hose was busted. I ordered the parts from this site and... Read more

• Will not agitate
• won't spin

Ordered part took seal off to gain access..couple of screws and connectors..bk in business Read more

Replacing the upper nozzle connector did the trick. I could not see damage in the older upper nozzle, it is possible that I could have fixed this just by tightening the parts - but i am happy I purchased both the upper nozzle and check valve ball, it feels good to have installed brand new parts in the washer. Read more

The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more