Poulan Lawn Mower Parts

Replacement blade cap assembly for riding mower tractors. Secures mower blade to spindle shaft. Replace if cracked, broken, or missing for safe operation.

Lawn tractor won't start when you turn the key? This starter solenoid links your battery to the starter motor. Common DIY fix for no-crank issues.

Primer bulb assembly kit for chainsaws. Installs on the carburetor to circulate fuel for easier starting. Replace if bulb is cracked, hardened, or worn.

A V-belt is responsible for transmitting energy. It is made from a thick and sturdy rubber material. It features grooves for improved traction and measures ½ x 95-1/2. A worn-down v-belt can lead to inefficient energy loss, and therefore poor performance. Installing this v-belt requires pliers and a wrench. First, the spark plug wire needs to be removed. Then, position the mower deck to the lowest possible level. Move the machine's blade engagement level to OFF. Remove the belt found from the engine pulley. Don't forget to take out the bow-tie pins and blade engagement cable as well. Remove the bolt from the pulley cover and loosen the nuts found at the idler pulley. Put the new belt and then tighten the nuts on the idler pulleys. The deck can now be re-assembled to its original position. This Husqvarna 532144959 V-Belt OEM Replacement can help keep a lawnmower in top condition. This genuine Husqvarna made V-belt is specifically for driving the blades on a lawnmower. It is compatible with Ariens, Craftsman, Poulan Pro, Dixon, and Husqvarna mowers. This V-belt is sold individually.

Mower won't start or starter doesn't engage? This ignition switch activates your riding mower's electrical system. Simple DIY repair in under 30 minutes.

This genuine Husqvarna fuel cap provides cover and protection to the hole into which engine oil is dispensed on certain lawn mowers, lawn tractors, and snowblowers. This fuel cap should remain closed when the appliance at hand is not in use in order to prevent leakage.If the engine of a small engine appliance is suffering from frequent leakages, there could be damage in the fuel cap that is causing the leaks. A fuel cap could also become misplaced. If the cap is broken or lost, it must be replaced immediately before using the small engine appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This fuel cap is compatible with the following brands: Husqvarna, Poulan, Ariens, and Craftsman. This part is sold individually.

Secures the mower blade to the motor shaft. Replace if adapter is worn, stripped, cracked, or no longer holds the blade firmly in place during use.

Steering shaft connects the steering wheel to the gearbox on riding mowers and lawn tractors. Replace if bent, cracked, or worn for proper steering control.

This is a genuine OEM replacement drive V-belt for a riding lawn mower. The drive V-belt attaches to the drive pulley and transfers rotational motion from the transmission to the mower blade. This causes the blade to then spin and cut grass. By using a belt to transfer motion, the engine does not have to work as hard to spin multiple parts, meaning that it runs more efficiently. Drive V-belts are made of a rubber composite material that will begin to fray and stretch over time. Due to continuous motion, these belts absorb a lot of wear and tear, and if left for too long, they can eventually snap and leave the mower blade non-functional. Therefore, it is wise to check the condition of a V-belt during regular maintenance. As soon as it appears to be wearing away, replace it with a new part using a nut driver and screwdriver. When detaching the lower deck, be sure not to lose the bolt clips, as they are required for reassembly. As a high-quality replacement part, this drive V-belt is directly sourced from its original manufacturer. It is compatible with riding lawn mowers made by Husqvarna, Poulan, Craftsman, and Jonsered. This part ships individually.

Replacement drive control cable for walk behind lawn mowers. Installs to connect drive mechanism. Replace if snapped, worn, frayed, or damaged.

Mandrel spacer washer for riding mowers and lawn tractors. Installs between drive pulleys to maintain proper alignment and spacing. Replace if worn or missing.

Hardened washer for lawn tractors and riding mowers. Installs with bolts to redistribute pressure and prevent loosening. Replace if worn or missing.

Secures the mower blade to the spindle on riding mowers and tractors. Replace if bolt is stripped, washer is damaged, or hardware is missing.

Idler pulley for riding mowers and tractors. Maintains proper belt tension for drive system. Replace if pulley is cracked, worn, or spinning rough.

Husqvarna makes this replacement wheel assembly, which measures 8 inches in diameter and has a width of 1.75 inches. The purpose of this wheel assembly is to keep a lawnmower mobile to ensure a lawn or yard has a clean and well-maintained appearance. If the lawnmower's self-propel function is not working, the drive gear on the wheel may be stripped and need to be replaced. It is a relatively simple task that will only require a wrench. First, the lock nut will need to be removed before the old wheel is taken off. Install the new one and secure the lock nut. Aside from Husqvarna, this part is also compatible with other lawnmower brands, including AYP, Craftsman, Dixon, Jonsered, McCulloch, Poulan, Poulan Pro, Redmax, and Weed Eater. It is an OEM part sourced directly from the manufacturer and is sold individually.