Parts for Maytag MLG20PRBWW2: 12 - Pump And Motor Parts

The Drive Motor is an OEM part for Whirlpool washers. It drives the agitator or drum, allowing the washer to perform its function of cleaning and spinning clothes. It provides the necessary rotational force to agitate the clothes during the wash cycle and spin them dry during the spin cycle.

A faulty or worn-out drive motor can occur due to various reasons, such as electrical issues, mechanical failure, or excessive wear over time. If you notice symptoms such as the washer not agitating or spinning, a burning smell coming from the motor, or unusual noises during operation, it may be time to replace the drive motor.

Symptoms of a bad drive motor include:

• Washer not agitating or spinning
• Burning smell coming from the motor
• Unusual noises during operation

Restore the efficient performance of your Whirlpool washer by replacing the faulty or worn-out drive motor with this genuine OEM part.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This replacement screw secures appliance panels and trim so components stay properly aligned and vibration is reduced. Use it to replace missing or damaged fasteners and restore a secure fit for safe operation. What it does:

• Fastens control panels, trim pieces, or access panels to the appliance frame
• Prevents panel movement, rattling, or gaps that can form from loose or missing screws
• Restores proper alignment after service or part replacement
• Helps maintain safe, stable operation by keeping panels secured

• Disconnect power (and gas if applicable) before servicing the appliance
• Use the correct driver bit and thread engagement; hand-start threads to avoid cross-threading
• Do not overtighten — snug until secure to avoid stripping or damaging panel threads
• Keep removed hardware organized to ensure correct locations during reassembly

Air chamber for water level pressure switch hose.

This wire harness connects the motor to the appliance's power and control wiring, restoring reliable electrical connection for motor operation. It replaces a damaged or worn harness to help restore normal motor function. What it does

• Carries power and control signals between the motor and the main wiring harness or control board
• Can resolve intermittent motor operation, no-start conditions, or loss of motor power when the fault is a damaged connector or wiring
• Replaces frayed, burned, or broken wires and damaged connector ends that prevent proper motor function
• Helps prevent arcing and poor connections that can cause overheating or electrical faults

• One motor wire harness

• Disconnect power to the appliance before beginning any repair to avoid electrical shock
• Verify the harness matches the original by comparing connector shapes and pin count before installation
• Route and secure the harness away from moving parts and sharp edges; use existing clips or ties
• If you see damage to the motor or control board connectors, inspect those components and replace as needed

This 2-pack of dryer vent clamps secures the vent hose to the dryer outlet and the wall/vent hood. A tight connection helps maintain airflow, reduce lint leaks, and keep the duct from slipping off during use.

• Tightens around the vent hose to hold it securely to the dryer exhaust collar or exterior vent
• Helps prevent hose detachment, air leaks, and lint escaping at the connection
• Supports proper exhaust airflow by keeping connections sealed and stable
• Common symptoms pointing to replacement: hose won't stay on, visible gaps or lint around fittings, rattling at the vent, or longer dry times from poor ventilation

• Disconnect power; for gas dryers, shut off gas supply before moving the appliance
• Slide a clamp over the hose, seat the hose fully on the collar, position clamp over the fitting, and tighten with a screwdriver or nut driver
• Do not overtighten; avoid crushing thin foil ducting; ensure the hose is straight and not kinked
• Restore power and verify strong airflow at the exterior exhaust

The Tub to Pump Hose is an OEM replacement part for Whirlpool washing machines. This hose serves as a conduit, allowing water to flow from the tub to the pump, and facilitating the drainage process after a wash or rinse cycle. 

Causes for a malfunctioning Tub to Pump Hose can include blockages from lint, small clothing items, or other debris, cracks or wear in the hose material, or loosening of the clamps or connectors that secure it in place.

Symptoms of a bad Tub to Pump Hose include:

• Water leaking from the base of the washing machine
• Slow or incomplete drainage after a cycle
• Unusual sounds, such as gurgling or splashing, during the drain phase
• Error messages related to water drainage or pump issues

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

The Spring Tension Hose Clamp is an OEM part for Whirlpool washing machines. It is designed to secure hoses in place, preventing leaks by maintaining consistent tension on the hose connections.

Over time, spring tension hose clamps can lose their effectiveness due to metal fatigue, corrosion, or damage from frequent tightening and loosening. This can lead to leaks and improper hose connections.

Symptoms of a bad spring tension hose clamp include:

• Water leaks around hose connections
• Loose or disconnected hoses
• Unusual noises or vibrations during operation
• Water pressure issues within the washing machine

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Pump is an OEM replacement part for Whirlpool washing machines. It plays a key pump function by introducing water into the wash tub. Proper water circulation is necessary for effective cleaning.

Symptoms of a faulty pump include: 

• Slow or no water filling during wash cycles    
• Water leaks or drips due to cracked pump housing
• Loud grinding or knocking noises during operation
• Error codes for water fill related issues

Causes of pump failure can be due to regular usage over time, mineral buildup inhibiting flow inside the pump, or cracks developing in the plastic housing exposing internal components to corrosion.

This OEM Whirlpool replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models. 

This inner outlet hose routes water from the unit's internal pump/sump to the discharge path. Replacing a cracked, kinked, or clogged hose restores proper water flow and helps prevent leaks or cycle interruptions.

• Directs water from the internal pump/sump to the outlet within the machine
• Maintains a watertight path when secured with clamps
• Wear, heat, or mineral buildup can cause cracks, kinks, or blockages
• Common symptoms: leaks inside/under the unit, slow or no draining, restricted flow, or drain-related error messages

• Disconnect power and turn off the water supply before servicing
• Expect residual water; place towels or a pan to catch spills
• Note hose routing and clamp positions; transfer existing clamps or install new ones
• Seat the hose fully on fittings, tighten clamps evenly, and perform a short test run to check for leaks

Drain hose retainer keeps the appliance's drain hose securely fastened to the cabinet or pump, helping prevent the hose from slipping loose. Replacing a broken retainer reduces leaks and improper draining caused by a detached hose. What it does:

• Secures the drain hose to the cabinet, pump outlet, or drain connection to maintain correct hose positioning.
• Helps prevent water leaks and hose disconnection during drain cycles.
• Common symptoms of a failed retainer: visible hose movement, water at the rear or floor, or intermittent draining issues.
• Replaces worn or broken retainers that no longer hold the hose firmly.

• Always disconnect power and turn off water before servicing the appliance.
• Access may require moving the appliance or removing a rear/access panel to reach the hose retainer.
• Seat the drain hose fully in its proper position, snap or clip the retainer into place, and verify the hose is secure and not kinked.
• Inspect the drain hose for cracks or wear while replacing the retainer; replace the hose if damaged.