Gerry B January 03, 2017 for Model Number fghs2631pf4a Our Frigidaire side by side is a little over 1 year old. I replaced the ice maker pin prick needle feeder valve with a compression valve. The next day (less than 24 hrs.) the inside of the freezer had frozen water all the way down the back and onto the top of the bottom tray. I cleaned it all up and in less then two hours it had started again. Fridge is now off. Could the new valve be allowing too much water? Also, the water filter replacement light is on. We have the house on the market and do not use the fridge regularly anymore. This problem started when I had to replace the feeder valve.
1 Answer Gerry, This issue does sound like it could be caused by too high of water pressure and would suggest if able, reduce the flow of the water. If it continues to happen then it would be a faulty water valve. For the filter you would want to reset the light at the dispenser assembly. Read More...
Bill December 09, 2016 for Model Number plhs269zdb4 MY ICE MAKER ONLY MAKES 3-4 CUBES AND THEY SOMETIMES HANG UP WHEN THEY DISPENSE ( I think they be a little small).Whats the problem.
1 Answer Hello Bill. It sounds like the water valve is bad and will need to be replaced on the unit. Read More...
Barbara October 30, 2016 for Model Number 25354364490 Ice maker has 2 options "cube or crushed" When I push for CUBES it's crushed ice on both options. Thank you for your help.
1 Answer Barbara, When you pull out the ice bin, next to the auger in the back of the freezer there will be a square hole, you will want to check to make sure that the arm of the solenoid is in the down position. If it is in the down position then make sure that it is not damaged. If damaged then it would need to be replaced. If it is not damaged and just in the up position then pry it down with a flat blade screwdriver. Read More...
Julie Riley September 15, 2016 for Model Number Fgtr1845qp1 The ice maker , it makes eight cubes at at time, that came with our refridgerator a frigidaire model number fgtr1845qp1 can't keep up with our ice demands. I have to buy additional ice every week and there is only 2 of us here at home. I want a larger ice maker. Does one exist for this model?
1 Answer Julie, Unfortunately there is not a larger icemaker for this unit. The average amount of cubes in any refrigerator will be 8 cubes at a time. Read More...
Paul August 16, 2016 for Model Number FGHS2631PF4A All of a sudden, after almost two years, our Frigidaire ice maker On/Off switch will not stay On. Do I have to buy a new ice maker or is there just a part I need to buy?
1 Answer Hello Paul. If the switch does not work, you will need to order and replace the icemaker 5303918344 on the unit. Read More...
Greg August 06, 2016 for Model Number PHS69EJSS2 SN4A91220538 Ice Maker P/N 241709804 Model# 20-1 Ice make does not fill with water. Water dispenser works there was a wet spot on the floor in the back of the unit when I pulled it out. Could the water valve be bad? What is the water valve replacement part # and $$.
1 Answer Greg, The water valve would be the most likely cause for the icemaker to not fill, but you will want to make sure that the fill tube is not frozen. If the fill tube is frozen it is caused by the valve. The water valve for this unit is part number 242252702. Read More...
Don June 23, 2016 for Model Number 25354364401 I need to replace the ice maker on a Kenmore side by side. The model number is 253.54364001. It's a rear mounted unit. The video for part number AP4299334 displays a side mount unit. Are the two products the same? Thank you.
1 Answer Hello Don. Based on the model number you provided, 5303918344 is the correct icemaker. Read More...
1 Answer Hello Charlie. Make sure the ice cubes are the correct size. If the cubes are too small, you will need to replace the valve. If the cubes are correct, then replace the icemaker. Read More...
Moshe December 19, 2015 for Model Number GLHS238ZDSA I purchased and followed the instructions for replacing the water dispenser actuator. However, when re-assembling I found it impossible to insert the water supply tube into the hole of the assembly. Any suggestion?
1 Answer Hello Moshe. You will need to take it back apart and install the hose in the proper location. Read More...
Jeff December 16, 2015 for Model Number 241621901 On my Frigidaire ice maker I keep getting frost on top of the ice maker and under the bin that covers the ice bucket but no where else in the freezer is there frost. Could this be a bad heater inside the ice maker causing the frost or something else in the freezer causing it?
1 Answer Hello Jeff. You need to check and see if the flap is closing on the unit. If not, then the solenoid may be bad and need to be replaced on the unit. Read More...