Rodney November 10, 2012 for Model Number GSD4020Z02BB My dishwasher has power, but no lights come on when I latch the door to start up. I traced the power in the door and the black wire is hot going to the "Control ASM" and the "Sequence Switch" but there are no lights on at all. I suspect it's the Control ASM. The lockout switch clicks when depressed.
1 Answer Rodney, Ok, based on your post, we know you have L1 (power in) but, do you have Neutral (power out). Check for 120 VAC across the "D" connector(four pin connector) , pin 4 black and pin 3 white if you have 120 VAC across the wires, replace the control board WD21X10100. Read More...
Siming January 19, 2012 for Model Number GE ZBD3500ZZ1WW When I put my dishwasher in Rinse & Hold mode, it can drain all the water when it's done. So the water pump and drain solenoid should all be working. But when it is in full washing cycle mode, it goes through all stages just fine. But at the end, it leave a full tank of clean water in the washer. I have replaced Sequence Switch (AP2039701) and the control board assembly (AP3191005). But the same problem still exists. Any other ideas? Thanks much.
1 Answer Hi Siming. Did you totally remove the drain hose and verify it is clear ? Is the check valve flap inside the pump output in good shape so the pump does not cavitate ? It is part # WD01X10175. It also helps to insure that there is no back up of sink water. You need to verify that there is a loop under the sink clamped tight as high as possible then taught to the sink drain or disposal. This will create a p-trap effect as no sink water or drain waste smell back up in the unit. Make sure the sink or disp. connection is clear to drain into it. Follow the installation instructions supplied with the use and care guide. The pump is part # WD19X10015. Look inside the pump and check the impeller to see if it is damaged or loose spinning on the shaft. Thank You. Read More...
Siming January 06, 2012 for Model Number GE ZBD3500ZZ1WW When I put my washer in Rinse&Hold mode, it can drain all the water when it's done. So the water pump and drain solenoid should all be working. But when it is in full washing cycle mode, it goes through all stages just fine. But at the end, it leave a full tank of clean water in the washer. I have replaced Sequence Switch (AP2039701). But the same problem still exists. Any more ideas? Thanks much.
1 Answer Hello Siming. Based on the information, it sounds like the control board assembly WD21X10116 is bad and will need to be replaced. Hope this helps. Read More...
Siming Mu December 30, 2011 for Model Number GE ZBD3500ZZ1WW When I put my washer in Rinse&Hold mode, it can drain all the water when it's done. So the water pump and drain solenoid should all be working. But when it is in full washing cycle mode, it goes through all stages just fine. But at the end, it will leave a full tank of clean water in the washer. Which part is having problem? Thanks much. Siming
1 Answer Hello Siming Mu. Based on the information you provided, it sounds like the sequence switch WD21X10018 is bad and will need to be replaced. Hope this helps. Read More...
Glen July 09, 2011 for Model Number GSD4800G00WW The tub is still full of water at the end of the wash cycle. The pump is working. I have observed it running into the disposal between wash and rinse cycles. The solenoid that controls the valve on the pump is also working. I've observed it allowing water to flow in and then switching to pump water out. But the tub is full at the end of the cycle. I'm guessing the sequencer (#904 on the blow-up diagram) needs to be replaced. You thoughts???
1 Answer Hello Glen. You will need to remove the drain hose and see if it is partially clogged. If so, it can do a slow drain into the disposal, but will not empty out the water inside the tub assembly. Remove the drain hose from the check valve assembly WD22X10024 and make sure the drain hose and the check valve assembly are free from debris. Hope this helps. Read More...
John P. June 14, 2011 for Model Number GSD5110D00AA At start-up, the dishwasher put some water in the tub and then the water quits. It does not seem to fill to the float. The d-washer then runs with no water being sprayed. Is it my timer?
1 Answer Hello John. You will need to check and see if the water valve WD15X93 is letting in enough water. If not, it can cause low water levels. If it is good, you may have a bad timer WD21X10018. Hope this helps. Read More...
Dick W. April 14, 2011 for Model Number GSD4330Z02WW My diswasher will not start. The control screen just shows "CLEAN " green light and it keeps blinking. What parts could be broken? (I already change a new control asm).
1 Answer Hello Dick! I have located a link on our free repair forum that will help you determine the issue, hope it helps! http://forum.appliancepartspros.com/dishwasher-repair/174843-stuck-clean.html Read More...