Hua April 20, 2020 for Model Number LRE 30451SB/02 The F-1 code came after I ran a self cleaning cycle. At beginning, I cleared the code by press the clear button, then tried to turn on the burners, was able to use one at a time, not two burners at same time, while the f-1 code came back in a few minutes, clear it again and again, some oven buttons worked. First attempt: Turn off the power, open the back, I cleaned ribbon cables, make sure put them back all the way in, pulled some connectors out, then back in. turn the power back, pf showed on keypad on all the burners, press on/off buttons, pf disappeared, time shows on the display, but all the other buttons are not working anymore! f-1 code comes back in a few minutes again, clear it off, comes back in a few minute..., only on/off buttons work. Second attempt: Turn off the power, disconnected the ribbon cable, turn on the power, the pf showed on all the burners, and PF showed on the display too, wait for a 5 - 10 min. the f -1 code doesn't come back! Does it mean the temp sensor is still good? Any suggestion as to which part should I try to replace first? Thanks.
1 Answer Hua, The F1 error does not have anything to do with the oven sensor as being the issue. This would be a faulty touchpad that will need to be replaced. Read More...
Jan July 24, 2018 for Model Number LRG3095ST When I try to use the oven, on convection or conventional, I get an F11 error. It has the orange glow but after a few minutes of waiting for it to warm, it will beep and give me the F11 error. My husband has had a lot of illlness lately and I can't afford to "have it fixed" so I plan to attempt this on my own. Any ideas?
1 Answer Jan, if the igniter is glowing, then you know there is voltage present, I would replace the oven igniter, part number is MEE61841401, there has to be enough resistance for the igniter to open the gas valve. Read More...
Gerald C November 19, 2017 for Model Number LRE3021ST/00 Everything on the stove works except for the chimes. No sound at all. What could be the problem.
1 Answer Gerald, The unit may have the beeper volume turned down and you will want to try the following. BEEPER VOLUME 1. Press the SETTING button until “Beep” appears in the display. 2. Press the 1 button for LOUD, 2 button for NORMAL, 3 button for LOW, and press the 4 button for MUTE. 3. Press the START button to accept the change. NOTE On models with only two volume settings: Press the 1 button for NORMAL, or the 2 button for MUTE. Then press the START button to accept the change. Read More...
Gel February 09, 2017 for Model Number Lre 0453sb/00 On erb74632605 pic board does top cables need to be rotated 180 degrees to plug in? Also do ribbon cables also have to be done the same way.
1 Answer Gel, the ribbon harness should not have to be turned to plug it in and the top cable should not have to be either but it may need to be. Read More...
Todd January 17, 2017 ebr74632601 Wondering why the heating element relay is so damn noisy, the old version was a lot quieter, and yes there are 2 pin strips that u have to 180 degree switch to plug in. They are the white ones. The blue one are 180 out to if u pull the retaining clip off as well.
1 Answer Todd, The relay should not be noisy on the control board. if the relay is noisy then it would most likely be a bad relay which would require the board to be replaced. Read More...
Emil January 11, 2017 for Model Number LRE3012 Hi the start button will not function on the touch panel. All other buttons work. All of the stove top works. So if I hit the bake,set the temp, those work but when I hit start it will not start the operation. Let me know. Thank you.
1 Answer Emil, You will want to access the control board and make sure that the ribbon harness is seated properly with no corrosion on it. If this checks ok then the range touch control will be the most likely cause for this issue. Read More...
Kevin June 14, 2016 for Model Number LRE30451SW The right side burners do not work or work very intermittently, left side works, center warmer works. Oven can be turned on but the start button does not work. Thinking its the oven control board (PCM) EBR74632601 and 6871W1N01B from your site? What does the oven board do, 6871w1w012b or does it even have that part replaced by the oven control board (PCM)?
1 Answer Kevin, The most likely cause for the 2 elements on one side to not work and the start button to not start the oven would be a faulty control board EBR74632601. Read More...
Lois December 01, 2015 for Model Number LRE30451SB The clock, timer, and cook time buttons will not work. Sometimes I cannot adjust the heat on the largest burner.
1 Answer Hello Lois. You will need to order 383EW1N006F and replace the control panel on the unit. Read More...
William July 27, 2015 for Model Number LRE30451ST My oven is over heating. When it is set for 350°, it goes as high as 500° or higher. I replaced the thermister and problem is still occurring.
1 Answer Hello William, If the PTC thermistor harness has no issue, the issue will be a sticking relay on the control board EBR74632601. Read More...
Bill March 26, 2015 for Model Number LG Model # LRE30453ST/00 I'm having a problem reading the displays on my stove. The clock and the burner digital displays are missing pieces so they cannot be read. The burners and all other features seem to be working. Thanks
1 Answer Hello Bill, You will need to replace the PCB assembly EBR74632605 to correct the display issue. Read More...