Amanda D November 26, 2018 for Model Number AFI2538AES7 Will not buy another Amana or Whirlpool product. Need electronic board # 67006294 for a 6 year refrigerator have been told manufacture no longer makes. any suggestions.
1 Answer Amanda, Unfortunately the manufacturer has discontinued this control board and there would be no suitable replacement available. Read More...
Bob November 10, 2018 for Model Number mfi2568aeb The lights inside work but the front panel shows 0 and 38 for numbers and filter light red i have tried to reset, door alarm light stays on lock/unlock light stays on, and light auto stays on. The ice and water will only work when you hold lock in but only for a sec. What do I need to replace or do Thanks Bob
1 Answer Bob, let's try a simple reset by unplugging and waiting 5 minutes before plugging the unit back in. I will send you a tech sheet or some info if the problem persists. Read More...
Wanda July 19, 2018 for Model Number Mfi2266aes The dispenser circuit board has gone out for the 3rd time and I'm having trouble finding one. Is there a generic replacement part that isn't showing online?
1 Answer Hello Wanda, I'm sorry but this part 67006294 has been discontinued by the manufacturer and no satisfactory substitutions have been provided. Thank you for your patience and understanding in this matter. Read More...
Blake May 27, 2018 for Model Number Amana AFI2538AES6 After a power outage, display is blank and refrigerator and freezer do not start. Inside lights work. Would it be the low voltage PCB (67006294) or the high voltage control PCB (W10890094)? Pressing any button on the keypad causes all display segments and L.E.D.s to illuminate. Tried entering the service mode with keypad and does not work either. Activating the ice/water level in door dispenser causes alarm to sound.
1 Answer Hello Blake, the interior lights and display all run of the low voltage board. The issue you are describing is more than likely caused by the high voltage board part number WPW10310240. Hope this helps! Read More...
Robert May 12, 2018 for Model Number MFI2569VEM1 This model number is for a Maytag French door bottom freezer unit. My problem is that the ice dispensing worm drive motor does not stop when you are finished and will spew ice all over the floor. Similarly to other posts here, sometimes the motor will energize on its own, overfilling the "chute". The entire "chute" assembly was replaced and it did not correct the problem. Next, the main circuit board on the rear was replaced, twice, 28th separate replacement boards. Each replacement resulted in the same condition. The front control board displayed "PE0000. Nothing would function on the door control panel to allow the required programming which for my unit is code 2020. Ice reinserted my original board and all functions are back to normal except the malfunction as noted. What's my problem? Thanks
1 Answer Hello Robert, This is normally caused by a sticking switch on the chute assembly WP13005705. If this does not correct the issue, I would recommend checking the wiring harness where it passes through the door hinge for a possible shorted harness. Read More...
Jerry August 11, 2017 for Model Number MFI2568AES Ice and water don't dispense till right french door is opened, ice works every time but not water, it works sometimes when door is opened then shut. What is going on ? ( low voltage pc board ?)
1 Answer Jerry, You will want to check the door switch on the unit just to make sure that it is good because if the switch goes bad it would cause the dispenser to not work. If this checks ok then this will likely be the dispenser low voltage board that is causing the issue. Read More...
Brian August 06, 2017 for Model Number 59677539600 Our Kenmore fridge is 11 years old. All of a sudden today the ice door started to flap open then closed every 5 seconds or so and the front display was flashing and the ice and water functions did not work. I Googled the issue and found that the likely cause was a faulty control board. I removed the front panel and disconnected the 3-prong connector which stopped the ice door from flapping. My question is: Which control board do I need to replace the main board #67006294 or the button control board #W10740217? It looks like they are relatively to replace without the help of a tecnician.
1 Answer Hello Brain. Usually this is caused by the HV board W10890094 needing to be replaced in the unit. Read More...
Bill July 26, 2017 for Model Number AFI2538AEQ board 67006294 will just go dead . it can stay off for a min. or two or stay off for an hour. but than back on by it self and work for a week or two before it acts up again. any sugestion ?
1 Answer Bill, First check should be a the wiring harness connectors at the LV control board, left door hinge connector and the main/Hi vac board on the back. Being a 12 volt low voltage circuit(s) it doesn't take a lot to disrupt the circuits. when you're checking the wires especially at the connectors, carefully twist, push and pull on the wires as close to the housing as possible, There should be little to no movement in the wires, if there is then the internal retainer is weak or broken and you'll need to extract the wire and repair/replace the retainer clip on the metal terminal on the wire. Read More...
Pat June 16, 2017 for Model Number AFI2538AEB Left door display is blank and ice door opens and closes. Some of the repairs talk about a HV part and others talk of a LV part. Which one would I need? Also I am not sure if the refrigerator is cooling. I do not believe it is.
Shane P March 13, 2017 for Model Number Magtag Fridge - MF12269VEM2 We've had the this fridge for approximately 6-7 year and love it. Yesterday we came home to find the display panel blank and when you touch any button it displayed all digital zero's (8's). Further when you press the Freezer Temperature control - up & down, the ice flap opens and closes. The fridge and freezer are not working, although the lights inside are. I had unplugged the unit for approximately 30minutes (twice) then plugged it back in, at one time it did display both the freezer and the fridge temp, then blanked out again, after which if you pushed any button it displayed zero's. This seems to be a common occurrence with these units and I believe it to be the Main board at the rear of the unit which I intend to change, but could it be anything else?
1 Answer Shane, You will want to check the wire harness at the door hinge to make sure that there are no loose or damaged connections. If this checks ok then the main board will most likely be the issue. Read More...