Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Dishwasher Food Chopper Assembly by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM17951346
Manufacturer Part Number: W10083957V

Dishwasher leaving film on dishes or making loud grinding noises? A worn food chopper assembly is often the culprit. DIY-friendly repair in under an hour.

More
$34.75

IN STOCK
Ships Tomorrow Guaranteed
Add to Cart

Questions & Answers

For Whirlpool Dishwasher Food Chopper Assembly (Part Number: OEM17951346)

Hilda A. for Model Number Kitchenaid KUDi02iRWHO

The dishwasher is not getting the dishes clean. Water doesn't get to the top rack. The spray arms spin and water does fill up in the bottom of the dishwasher. I've poured three boxes of baking soda and vinegar down the holes. It is sounding more like the chopper problem than the inlet valve. How do I get the gray button off the top of the sprayer to remove it to check the chopper and clean it out? The button doesn't turn by hand at all.

1 Answer

Hello Hilda. You will hold the hub WP8268342 and turn the lower spray arm to unscrew it from the hub nut and remove the spray arm. Hope this helps.

Read More...

1 Answer

Berkwood, It should not be that difficult, unless theres some sort of build up on the housing. "3. Remove the screw securing the foreign
object protector to the sump base and remove the protector 4. Remove the screw securing the inlet protector to the sump base and lift the inlet protector out 9 in some cases, the opposite side of the protector is "keyed" into a "slot" opposite the mounting screw. 5. Remove the chopper assembly from the impeller shaft and lift it from the sump base. 6. The check valve, located between the wash motor and the drain can be removed with a pair of needle nose pliers." Good Luck and Thanks

Read More...

1 Answer

Db, Yes, you can install the chopper and screen from the top. Its a tight work area, but can be done. I may be wrong, but if the chopper blade drive lug is worn that bad, I'd expect the impeller shaft to be worn as well. Thanks and Good Luck

Read More...

1 Answer

Hi Ikost. The chopper blade will screw on the shaft assembly. You Need to try to stop the motor fan blade and also remove (unscrew) the blade assembly off. The chopper assembly part # is W10083957V. Thank you.

Read More...

1 Answer

Hello Ugo. You will need to remove the lower spray arm and the cover off the sump assembly. Once the cover is removed, you will need to remove the cover over the chopper blade. You can now access the chopper. Pull upward on the blade filter and the chopper W10083957V will lift out of the sum assembly. Reinstall in reverse order. Hope this helps.

Read More...

1 Answer

Hi John. Check your drain hose and make sure it was installed correctly. It should enter in the side of the cabinet at the top rear corner and then have a loop clamped to the uppermost part of the inside of the cabinet. Then it should be taught into the plumbing connection under the sink. You need to make sure the hose and/or the plumbing connections are not clogged or restricted. Your drain hose may be the reason you are back filling into your sump and re clogging over and over. Is there anyone else in the home doing washes different then yourselves? I hope this helps. The chopper assembly is part # W10083957V. Thank you.

Read More...

1 Answer

Hello Gerry. You will snap the coupler onto the motor shaft, and the round disc sits in the grove in the sump assembly. These snap into place. Hope this helps.

Read More...

1 Answer

Hello Joe. It sits in front on the screen, and the screen sits in a slot in the sump assembly, holding the impeller onto the shaft, and locking the tabs onto the shaft. If it is broke, you will need to replace the chopper assembly W10083957V. Hope this helps.

Read More...

1 Answer

Hello Augy. It snaps onto the shaft. If the shaft is worn out, you will need to replace the impeller assembly 8193951A. You do not have to change the pump assembly. Hope this helps.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google