Eric January 27, 2012 for Model Number scd25tw I replaced the ice maker and the water valve. The water despenser works great but the icemaker is not filling. Water delivery to the ice maker was not part of my original problem.
1 Answer Hello Eric. Remove the wire from the dispenser valve and place it on the icemaker valve. Press the dispenser level and see if water comes into the icemaker. If not, then the fill tube may still be frozen in the unit, or the water line may not be seated in the valve. Hope this helps. Read More...
Karen January 16, 2012 for Model Number BR22TW (BOM: P1196710WW) When I get this icemaker to replace my old icemaker, can I reuse my old wiring harness or do I need to order the AP4427021.
1 Answer Hello Karen. As long as the old wiring harness is good, you can use the old wiring harness on the icemaker D7824706Q. Hope this helps. Read More...
Jodi January 14, 2012 for Model Number ars2661bs The ice maker will not trigger the water to fill the maker, therefore it doesn't produce ice. The water dispenser works fine. A repair tech assessed the side-by-side fridge/freezer and confirmed that the system is ok otherwise, but suggested that we replace the entire ice maker. I plan on repairing this myself. Do I need to replace the entire ice maker or can I repair the part(s) that is not switching on the water? Thanks!
1 Answer Jodi, The technician is certain you do not have 120 VAC on the wires to the icemaker solenoid on the fill valves WP12544002 and 12002193 ? if either valve has an "open" circuit or no voltage the icemaker will not fill and make cubes. Based on your post information, you would need the control module and motor assembly, which is not available as separate components, so you will need to order the icemaker assembly D7824706Q Thanks and Good Luck Read More...
Gary M. January 14, 2012 for Model Number GD5LHGXLT01 My ice maker quit working, the fingers on the ejection arm are not exposed anymore ( did not complete the cycle). Do I need to replace motor or entire ice maker ?
1 Answer Hi Gary. You may just have a bent ejector blade. You can remove the front cover and loosen the 4 - corner screws. Then you will have enough play to unjam the blades. If you see calcium build up in the cube areas, this will make ejection harder. You may ohm out the motor windings and the heater for resistance. Ultimately you may be a hole lot better off just to replace the whole ice maker part # 4317943. The thermostat needs to be closed at 14° in order for the motor to advance after the heater is on for approx. 6 seconds to help the ejection process. Thank You. Read More...
D.B.E. January 11, 2012 for Model Number 106.53634300 Is ice maker no. AP2984633 a complete ice maker assembly that will replace the existing ice maker in this side by side refrigerator freezer? The ice dispenser auger is mounted inside the ice dispenser bucket on the freezer side door.
1 Answer Hello DBE! The replacement icemaker used on the given model should be part number 2198597. Thanks! Read More...
Dan D. January 09, 2012 for Model Number msd2655hew Wiring harness can be plugged into back of refrigerator two different ways. Does the red wire go towards the top or on the bottom of the plug?
1 Answer Hello Dan. The wiring harness for the icemaker D7824706Q should have a d shaft on one of the plugs and can only be installed one way. If not, you will need to pull out the other end of the connector and match up the wires. Hope this helps. Read More...
Larry January 08, 2012 for Model Number 1069537654 I've been led to believe this ice maker will replace the one in my model 1069537654 Kenmore side by side refrigerator. Is this correct? Better still, my ice maker takes in water, freezes the cubes, but the arm with teeth will not flip the cubes out. Is there an easy fix for this problem? Thanks, Larry
1 Answer Hello Larry. Yes, based on the information, you will need to replace the icemaker, and 4317943 is the correct icemaker. Hope this helps. Read More...
Dennis V. January 07, 2012 for Model Number Amana TX21VL The icemaker works fine but water from the auger overfills and causes freeze up in the bottom of the tray and also a large icicle in the front of the tray. The fill valve was replaced about a year ago due to lack of ice production, which was successful. If flow adjustment is the problem, how do I get the cover off?
1 Answer Hi Dominic. Pry open the cover with a small blade screwdriver. Then you can see the small 3/8 " hole in the upper rt. corner. Inside this hole is a brass plate with a hole punched out in the center of it. This hole is centered from the factory so you get a avg. fill. Then you look to the immediate rt. and you will see the white screw head that adjust this fill adjustment. You only move this approx 1/2 turn either way from center. This will take the "black center hole" Lt. or Rt. Remember that Lt of cntr. water lets in. Then Rt. of center the water restricts. Ice maker part # D7824706Q. Thank You. Read More...
1 Answer Hello Alex. Yes, based on the model number, 4317943 is the correct ice maker. Hope this helps. Read More...
Larry December 27, 2011 for Model Number afd2535des No water to icemaker, but do have water at the cold water spiggot in the refrigerator. When the icemaker cycles, I only get 1 volt at the fill valve solenoid. Do I need to replace the ice maker.
1 Answer Larry, Try this, Disconnect the wires from the ice maker solenoid on the fill valve, Attach the meter leads to the wires and cycle the icemaker, if you have 120 VAC across the wires replace the fill valve WP67005154. If you have less than 100 VAV across the wires, replace the icemaker D7824706Q , and check for any loose connections in the harnesses. Good Luck and Thanks Read More...