Rich July 12, 2011 for Model Number 106.52572201 My icemaker has a switch on front which changes from regular ice making to accelerated ice making. Does this unit do the same?
1 Answer Hi Rich. No this replacement Icemaker is used on many brands. However you can use it with the Max- Ice part # WP2255794. Th ereplacement ice maker is part # 4317943. Thank you. Read More...
Chuck July 11, 2011 for Model Number 1069552621 Where is the adjustment screw for the water level in the icemaker?
1 Answer Hello Chuck! Remove the cover of the icemaker. There is an adjustment screw on the right side of the control module. Turn the screw clockwise to reduce the water level, but no more than 2 complete revolutions. Hope this helps you! Read More...
Fred S. July 11, 2011 for Model Number ED2SHAXMT10 Ice maker does not work. Unit on the door works, auger turns, but does not get supplied with the ice from the ice maker mounted in the freezer section ? This has an infrared assembly that senses the amount of ice in the bin ? Any suggestions ! Thanks.
1 Answer Hi Fred. Please remove the bottom kick panel from under the doors. This will access you to the technician wiring diagram and tech. sheet. This will help you diagnose which part might have failed. The infrared sensors do "see' the amount of ice in the ice bucket. This part # is W11629974. This is a kit which contains both emitter and receiver control boards. Thank you. Read More...
Pat July 10, 2011 I have whirlpool side by side refrigerater in-door-ice ice dispensing system ultraease 2 water filtration system. Icemaker stopped producing ice, still get water from the water side. If you fill up ice tray, it still will dispence it. What do you think is wrong?
1 Answer Hello Pat. Based on the information you provided, it sounds like the water valve is bad and will need to be replaced. We will need the model number to look the part up for you. Hope this helps. Read More...
1 Answer Hello Pat. Can you please provide more information on what your needing, and a model number? Thanks. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Ben July 07, 2011 for Model Number ABB2223DEW When I unplug my ice maker and then replug it in, 1 load of ice will complete and eject just fine, but the second load will fill the tray and freeze, but never release the ice. What could be happening that would prevent the ice maker from ejecting the second set of ice?
1 Answer Hello Ben. Based on the information you provided, it sounds like the icemaker thermostat is bad. To repair this you will need to replace the icemaker D7824706Q. Hope this helps. Read More...
Bangorme July 06, 2011 for Model Number ED22DQXDN01 I have a model ED22DQXDN01 Whirlpool side by side refrigerator that has stopped making ice. The icemaker dispenses ice cubes/crushed through the door and the auger is in the ice bin. When I look at it, the arm is in the intermediate position and the tray is full with ice. If I press the arm down, the ice ejects, the arm returns to the intermediate position, the tray fills and the arm doesn't go back to the lower position. Is there a specific part I need, or does the unit need to be replaced?
1 Answer Hello Bangorme! You will need to replace the icemaker assembly. Your part number is 4317943. Thanks! Read More...
Raul July 06, 2011 Icemaker tray inside freezer has cracked and is leaking water as it fills up. The water freezes all the ice in the tray. I need a replacement for amana model drb1801aw. Does the replacement tray have the harness to hook it up to the unit inside? Thank you
1 Answer Hello Raul. According to the model number you provided, D7824706Q is the correct icemaker. It does not come with the wiring harness. You can use your old one, or order a new harness WPD7813010. Hope this helps. Read More...
Dean July 06, 2011 for Model Number maytag # mzd2766geb Question #1, well as you will see, I have a lot of time on my hands. I started timing the cycles after it was shut all night and not opened. It runs 20-25 minutes on, and 20-25 minutes off. Except 40-45 mi. defrost, is this normal run time? I have the freezer slide set at 2&1/2 which gives me a 5-10 below zero. The frige slide is set at 6&1/2, which gives me 40%. Question #2, can I get 35 or is it preset? Question #3, what wood I gain by moving frige slide to 8 or 9? Question #4 , when leveling this side by side where do I put the level side2side and front2rear? Question #5, does this frige have a 24 hr. timer? Question #6, Thank you. I think this will be helpful 2 others.
1 Answer Hi Dean. Yes, your findings are all normal. All manufactures recommend both compartments at a "mid-" point settings. If you use a genuine quality temperature gauge, you can first monitor the center of your freezer cabinet. Get it set to -0 degrees , not colder than -2 degrees. Then put the gauge in the middle of your fresh food cabinet and set it between 37 degrees and 47 degrees , depending on how cold you like it. Yes the temperature capillary along with the actual controls are 'preset' (plus or minus 10%). You would really have both controls fighting against one another if you crank them up on the fridge side. The compressor runs to satisfy the fresh food temp. setting in relation to where it is set. By frosting the evaporator, freezing the freezer, the evaporator fan sends cold air through a damper control that is set by your freezer control. Therefore your fresh food section becomes cold. Yes, definitely take the time to level your unit as you explained. This allows the compressor to be operating level, along with the ice- maker and the doors closing properly. Yes this refrigerator has a Adaptive Defrost Control board. This controls your defrost , compressor run time, water usage monitor and vacation monitor definitions. This part # is 61005988. Thank you. Read More...
Randy July 02, 2011 What signals the water to come into the refrigerator. The water doesn't come into the refrigerator and it is not frozen. My ice maker is not making ice.
1 Answer Hello Randy. When the icemaker cycles, it sends power to the water valve to bring in water. This is just for a few seconds. You can test and see if there is power going to the water valve when the icemaker cycles. If so, and the water does not come in, you will need to replace the water valve. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps.http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...