Dave Z. October 06, 2011 for Model Number 6498VVD I get no spark on the top burners when I turn the knobs to the light. I assume it is the spark module is there a test to confirm the module is bad? Also where is the module located on my unit?
1 Answer Hello Dave. Yes, you can test for voltage coming to the spark module 12001596 when the switch is on. If so, and no spark, replace the module. It is located on the back frame of the range. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Buster September 26, 2011 for Model Number SC8830EBQ1 The ceramic ignitors on both right side burners are cracked. Can they be easily replaced?
1 Answer Hello Buster! If you are needing the ceramic ignitors on the burner assembly, they are not available separate from the burner assembly 74001260, which has been discontinued with no replacements available. Sorry! Read More...
1 Answer Hi Wayne. There can be a couple of device's involved. Commonly, the ignitor part # 74007498 may open so the gas valve wont emit gas. It should read 75-800 ohms cold with an ohm meter. If it is OK and not open in the middle, then the Safety Valve part # WP74009891 is defective not allowing gas to flow. Thank you. Read More...
Walter September 23, 2011 for Model Number Maytag CHB9800BAB Two questions: 1) For some time I have used a match to light all four burners on the top of my range. I get spark on all of them but it is usually intermittent on any one burner, and often doesn't seem to light the gas stream even when it sparks several times in a row. I have cleaned the gas ports around each ignitor, also checked for loose wires on all ignitors. Question: does the spark module produce a weaker spark over time, or does it usually work or not work? 2) My range has one high output burner, and I'm afraid that when I removed all of my burners I may have mixed them up. I cant see any difference in them. How can I tell which one is high output? Also, does a high-output burner usually have a high output orifice beneath it? Thanks for your help.
1 Answer Walter, Yes, spark modules can loose their high voltage output after quite some time,and produce a weak irratic spark. As long as the burner base and area around the burner are clean and moisture free, Repalce the spark module. The high output burner is the right front burner on your range, as long as you did not disturb the orifices or mounting tubes you'll be fine, the burner caps are all the same, the orifices are different. Good Luck and Thanks Read More...
James J. August 21, 2011 for Model Number mgc5430 gas cooktop My unit when pluged in keeps tripping my circuit breaker, works fine lighting with a match. How many parts could short out causing this to happen?
1 Answer Hi James. Remove power. This is more than likely to have a black(line) wire from a switch shorting or pinched. You will need to remove the grates,and burners. Remove the knobs. Lift the unit from the cabinet. Take the top assy. off. Inspect before touching anything because a direct short will tell on itself by leaving a black burnt spot somewhere. The switch is part # W10138052. This kit will replace all switch wires and switches. Thank you. Read More...
Keith August 10, 2011 for Model Number 31213XAA Hello, I have a Magic Chef stand alone range model 31213XAA that has 4 burners on top of which only two spark and light normally. The other two need a match or scripto lighter to lite. I just ordered and replaced all 4 burners since they were all old, and was surprised to see that the same two burners that didn't lite before are still not lighting. Is this the "spark module," and where is it located on my model Magic Chef? Thank you in advance for your answer.
1 Answer Hello Keith. Based on the information you provided, it sounds like the spark module 12001596 is bad and will need to be replaced. It is located on the bottom of the back of the range. Hope this helps. Read More...
Skyliner August 09, 2011 for Model Number JDS9860AAP Does the range need to be pulled out to replace the spark module?
1 Answer Hello Skyliner. Yes, the unit needs to be pulled out. 1. Remove unit from installation position. 2. Remove screws securing lower rear access panel. 3. Disconnect and label wire connections from the spark module. 4. Remove screws securing spark module 8215557 to unit chassis. 5. Replace and reverse procedure to reassemble. Hope this helps. Read More...
Michael D. August 07, 2011 for Model Number mgc6430bdb What causes all four igniters to spark when all the burners are turned off? I have to unplug it to make them stop.
1 Answer Hello Michael! It sounds like the spark module is shorting out 8215557 and needs to be replaced. Thanks. Read More...
Joe July 06, 2011 for Model Number 31ha-3kx My oven glow light comes on, but I have to tap on the part below it to get the burnner to light. Which part is bad and needs replacing? Is it the gas valve or control or what? Any help would be appreciated. Thanks much.
1 Answer Hello Joe. You will need to test and see if there is 3.4-3.8 volts AC at the gas valve with the igniter on. If not, you will need to replace the igniter 12400035. If the proper voltage is there, you will need to replace the gas valve WP7501P133-60. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps.http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Mike June 22, 2011 for Model Number CRG9700CAE Range is difficult to light. When one burner is turned to lite, ignitor can be heard but all 4 burners are sparking. Spark seems to be weak and intermittent and as a result selected burner usually does not light. This occurs regardless of which burner is selected to turn on. Is this a spark module issue? Thanks.
1 Answer Hello Mike. Based on the information you provided, it sounds like the spark module 12001596 is bad and will need to be replaced. If all four igniters are giving problems, it leads to the spark module. Hope this helps. Read More...