Scott C August 14, 2012 for Model Number Whirlpool Duet washer GHW9100LW2 My Whirlpool Duet washer water distribution assembly has become erratic, sometimes dumping the softner and soap together and sometimes skipping the soap altogether. The top of the distribution box was encrusted with calcium and water deposits. Cleaned that out and reassembled to watch. The accutator motor seems to work fine, but the lever connection and water distribution lever seems stiff, they seem to get stuck under the cam and the lever connection doesn't hit the II, III and IV marks precisely. It seems like the spring has lost enough tension to pull back the lever connection/water distribution lever to the proper point. I also pulled out the soap tray and watched the water dispense as I manually moved the distribution lever back and forth. Water comes out accurately above the soap box but when I move the lever to the bleach and softner boxes, water comes out all over the place. My diagnosis is to replace the nozzle, levers, spring and cam. I also suspect that there is a blockage or calcium buildup inside the water channels in the top of the box. Can I clean that out (LimeAway?) or should I just replace the entire distribution box. And by the way, what is the position I on the top of the box? It's clear that the cam/lever design never goes over to that position; water is dispensed into the soap box on II, bleach at III and softner at IV. Can you explain that? Just curious. Thanks for your help. Scott C
1 Answer Scott, Great description and diagnosis, you're on target. Replace the WP8181726, WP8181725,WP8181724,8181727. They have a tendency to flex, and go out of alignment with age, and usage. Thanks Read More...
Ron W. June 28, 2012 for Model Number WFW9500WT01 My Duet washer displays SUD and then F35. I have replaced the pressure switch and cleaned the drain screen. What Next?
1 Answer Hello Ron. Try blowing through the pressure hose and make sure it is clear. If so, you will need to replace the drain pump assembly 280187. Read More...
Steve1147 April 27, 2012 for Model Number GHW9150PWO My washer would run up to rinse, then shut down and show F-13. I ordered and replaced the dispenser actuator assembly. With the top off I watched, it now starts and washes all at position II, then when it hits rinse, the dispenser motor sweeps the pointer back and forth from I to IV pausing very briefly at each number, and after several full passes, shuts down again with error code F-13, what can cause this? Thanks! Steve W.
1 Answer Hello Steve, Here's what I've found on the F-13 fault code:F13 Dispenser circuit error If the dispenser motor is not able to be driven to it’s proper position.Potential Causes• Check mechanical linkage from dispenser motor to the top of the dispenser.• Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU)• Check Dispenser MotorReplace failed component.Read more: http://www.appliancepartspros.com/repairtips/repairtips_appliance+fault+codes.aspx#Whirlpool'>http://www.appliancepartspros.com/repairtips/repairtips_appliance+fault+codes.aspx#Whirlpool Duet Front Loading Automatic Washer Fault Codes#ixzz1tG7RVDqyhttp://www.appliancepartspros.com What this bit of information doesn't mention is that the control which is giving the fault code is using a self-diagnostic circuit. This self-diagnostic circuit is a man made circuit which can fail also. If, after you double check the dispenser, you cannot find a definate problem, the control WP8182695 is a consideration for replacement. Don't buy a control until you have thouroghly checked the dispenser as it is easy to overlook something. Read More...
Kim April 26, 2012 When I start the washer, the acuater moves from 4 to 1. However it moves from 1 to 2 to 3 to 4.. it stops on all 4. Nothing is dispensed. no water, not detergent, It doesnt spin or do anything. It will then cut off and then show the f13 code.
1 Answer Hi Kim., Here's what I've found on the F-13 fault code: F13 Dispenser circuit error If the dispenser motor is not able to be driven to it’s proper position. Potential Causes • Check mechanical linkage from dispenser motor to the top of the dispenser. • Check Wire Harness connections to the dispenser motor and Central Control Unit (CCU) • Check Dispenser Motor Replace failed component. What this bit of information doesn't mention is that the control which is giving the fault code is using a self-diagnostic circuit. This self-diagnostic circuit is a man made circuit which can fail also. If, after you double check the dispenser, you cannot find a definate problem, the control WP8182695 is a consideration for replacement. Don't buy a control until you have thouroghly checked the dispenser as it is easy to overlook something. The most common part for replacement is part # WPW10665207. Thank You. Read More...
Richard March 19, 2012 for Model Number ghw9300pwo Good afternoon, when my washer is not being use, it fill itself with water. Is it the valves that stay open? We don`t here the water going in. It takes a while.
1 Answer Hello Richard. Based on the information you provided, it does sound like the valve WP8181694 is leaking slowly and will need to be replaced in the unit. Hope this helps. Read More...
Loretta February 20, 2012 for Model Number GHW9150PW4 For a while now, my Duet has been dumping the fabric softener in at the beginning of the wash cycle, w/the detergent. Now, it seems that every other load, the detergent isn't getting dispensed into the machine. It's still sitting in the drawer at the end of the load. Could it be the Actuator? Is there any way to test it? I have already cleaned everything and made sure there is no build up of detergents or softeners.
1 Answer Hello Loretta. Remove the top panel and water the actuator during the cycle and see if it stops at all the stopping points. If so, the water valve is bad. If not, replace the actuator assembly WPW10665207. Hope this helps. Read More...
Richard January 24, 2012 for Model Number ghw9150pw4 I have a Whirlpool front load washer Model ghw9150pw4. The actuator moves to 2 when wash starts and ends at 4, I have soap left in the detergent tray and water in the bleach/softener tray. Is my actuator bad??
1 Answer Hello Richard. You will need to check and make sure both the hot and cold water valves are working properly on the unit. If not, you will need to replace the water valve assembly WP8182862. If the valves are good, then the actuator WPW10665207 could be bad and will need to be replaced. Hope this helps. Read More...
Michael L. December 12, 2011 for Model Number wfw8410sw00 My Washers plastic bar from the Dispenser Actuator Assembly moves from 4 to 1 when the washer starts but binds on a small plastic post from 1 to 2. If I stop it from moving over the post it will move from 1 to 2. It moves from 2 to 3 to 4 just fine. Thank you
1 Answer Hello Michael. Based on the information you provided, it sounds like the dispenser actuator assembly WPW10665207 is bad and will need to be replaced. Hope this helps. Read More...
Sheila August 10, 2011 I have a whilpool duet sport and it is giving me an F 30 code. Do I need a dispenser actuator?
1 Answer Hello Sheila. We will need your model number to help you with this. Thanks. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Joe C June 11, 2011 for Model Number ghw9150pwo Fabric softener does not dispense. Tray (Drawer) completely cleaned. With the top off watching the dispenser actuator assy, the pointer remains at # 2 and water is only dispensed into the detergent well. Is the problem with the motor and cam assy or is it an electronic timing issue?
1 Answer Hello Joe. You will need to test and see if there is power going to the motor on the dispenser. If so, and the motor does not move, you will need to replace the dispenser actuator assembly WPW10665207. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...