Eric W. July 21, 2011 for Model Number KSRS251HBL00 I have manually defrosted my refrigerator, which was warm. I know I likely have a defrost issue (either thermostat or timer, have ruled out defrost heater). Regardless of that, how cold should my refrigerator get? I have it turned to the highest cold setting and it is struggling to get below 50 degrees. Freezer seems to work fine, I feel airflow. Trying to decide whether to sink anymore money in to this appliance, about 11 years old and never seems to get below 40 degrees (45 recently) in refrigerator.
1 Answer Hello Eric. Sounds like your on the right track for the defrost problem. The refrigerator should get between 36° and 40°. Check and make sure the air flow chamber and diffuser WP2209751 does not have any ice in it blocking the air flow. If so, you will need to clear the ice out for proper operation. Hope this helps. Read More...
Eric July 21, 2011 for Model Number KSRS251HBL00 Freezer cools fine, refrigerator does not. Condenser coils looked excessively iced over, I manually defrosted and both worked fine for a few weeks before refrigerator warmed again. Noticed that the airflow has decreased and there is some frost on the inlet vent on the refrigerator side. Is replacing the defrost timer my best first step?
1 Answer Hello Eric! You will need to check and replace one of the three defrost system parts; defrost timer 4388932, defrost heater WP2323198, and defrost thermostat WPW10225581. You can test these parts using a multimeter MA-DM1. Here is a link from our free repair forum you can refer to for help with using a multi meter. Hope this helps, thanks! http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Ashok July 19, 2011 for Model Number kenmore 10654536400 Thanks for answering. Let me clarify further. I am looking at the harness and i see two white wires going to terminal 3(W), 2 pink wire going to terminal 2(PK), one orange going to terminal 1 (W) and one red going to terminal 4 (R) of the original timer. My new timer has same setup 2(PK) 1(OR) 4(R) and 3 (W). Hope that helps you visualize the setup. So with that you think the wire should still go to terminal 1(OR)? Thanks a million in advance.
1 Answer Hello Ashok. Yes, the black wire should go to terminal number one on the defrost timer W10822278, based on the information you provided. Hope this helps. Read More...
Ashok July 18, 2011 for Model Number kenmore 10654536400 I do not have the wiring diagram for this fridge. Can you please tell mw where the black wire goes to? I see two white wire to terminal 3, one red, one orange and two pink wire going to terminal 2 from the harness. Does that help you identify the correct terminal for the black wire? Thanks in advance. AG.
1 Answer Hello Ashok. What color of wires are on terminal 2, 1, 4, and 3 of the timer? You only gave terminal 2 and 3. If 2 is pink and 3 is white, where does the red and orange go? If red is on 4 and orange is on 1, then the black wire goes onto terminal number 1 of the timer W10822278. Hope this helps. Read More...
Boomer July 12, 2011 for Model Number roper refrigerator model? My refrigerator keeps freezing in the top mounted freezer slowly and gradually. I thaw it but eventually it will do again causing the bottom box to get warm. I checked the defrost heater for continuity and have nothing. I guess that means I have a break in the heater. Would you say that is the problem? I know it still could be the t-stat or timer. Please let me know.
1 Answer Hi Boomer. You can manually advance your defrost timer to the "start " of the 25 min. defrost time. Then you should have 120vac sent from the timer to the defrost thermostat. Under normal (frozen) temperatures, the defrost thermostat should be closed sending the 120vac to the defrost heater. Approximately 75% of defrost failures in unit 7-8 yrs old have a bad defrost thermostat. If your heater and thermostat are open, then yes by all means if you are already in the evaporator area replace both. If you will supply us with your exact model # , then we will be glad to assist you further. Thank you. Read More...
Paul K. July 08, 2011 for Model Number Roper refrig RT18DKXJW01 by Whirlpool - small freezer on top, mfg. October 2000 The refrigerator section of Roper model RT18DKXJW01 is not cooling well recently. In the past, it has gotten too cold in back. One person guessed a bad defrost timer or defrost element. How would I decide which and do you figure problem may be something else?
1 Answer Hi Paul. Depending on the temperatures in each sections then you will have different scenarios. Is the defrost timer allowing 120vac to come to the defrost thermostat ? Allowing (when the def. thermostat is closed), the 120vac to allow the defrost heater to come on? Your system usually defrosts in 6, 8 hrs., for approximately 20-25 minutes. The defrost timer is part # W10822278. Thank you. Read More...
Donald Duck June 17, 2011 for Model Number Whirlpool ET18PKXFW00 I replaced the defrost timer w/defrost timer kit#482493 in Dec of 2010. Connecting the lead wire to terminal #1. Refrigerator seemed to function well until recently w/ freezer coils icing up. Manually defrosted it, replaced the heater everything else seems to check out good. My question is did I connect the lead wire to the correct terminal or should it be #2? Thanks.
1 Answer Hello Donald Duck. It looks like you had it connected correctly. If not, the unit would not have worked correctly. Hope this helps. Read More...
Jon R. June 10, 2011 for Model Number ET19RKXGN00 >>If the unit is cooling, then the defrost timer is good. >>You will need to check the coils in the back of the >>refrigerator and make sure they are clean, and check >>the condenser fan motor to make sure it is running properly. The defroster heating element is staying on, but the unit is cooling fine. So the timer is not the issue. All we noticed is that if you touch the outside of the unit around where the defroster heating element is, it is VERY hot. Hot enough to burn your hand if you hold it there long enough. The defroster heating element is always on. Is this controlled in some way by the condensor motor or coils being dirty? I can check that, but it seems like there would be something else causing the defroster heating element to stay on. Or are you saying that it could be turned on because something is wrong with the condensor motor or the coil are dirty?
1 Answer Hello Jon. The defrost heater is located inside the freezer, behind the back wall, on the bottom of the evaporator coils. The condenser lines run through the frame of the refrigerator, not the defrost heater. They are suppose to get warm, but not too hot. If they are too hot, they are either dirty or the fan motor is not running. Hope this helps. Read More...
Jon R. June 09, 2011 for Model Number ET19RKXGN00 I believe that I need to order a defrost timer. My unit has been getting VERY hot around the freezer door for some time and now I notice that it stays hot all the time. The heat is noticeable on the outside of the freezer door around the front bottom of the freezer door and around to the sides. The dividered between the freezer and fridge is very hot to the touch and stays this way. So it seems that the defrost timer is stuck in the on position. So I assume that ordering another one would solve the issue. Is there anything else that might cause this issue as well?
1 Answer Hello Jon. If the unit is cooling, then the defrost timer is good. You will need to check the coils in the back of the refrigerator and make sure they are clean, and check the condenser fan motor W10822259 to make sure it is running properly. Hope this helps. Read More...
Mac June 07, 2011 for Model Number ED5VHGXMQ11 My refrigerator is running more then it should and I had to turn it down to keep it from running constantly. Where is the defrost timer located on my model and can I excess it from inside the freezer side with our removing anything to test it? Older models had access hole you could turn timer. Do you have a schematic/wiring diaghram for this model also? Thanks!
1 Answer Hello Mac. The model number you provided uses a defrost timer control board 4388932. It is located in the control section inside the refrigerator. If you provide your email address, we can send you the wiring diagram. Hope this helps. Read More...