Range / Cooktop / Oven Shaft Or Pin

This composite support stud mounts on the cooktop to provide a stable resting point for the burner grate. It helps keep the grate level and protects the cooktop finish from metal-to-enamel contact.

• Supports and levels the burner grate at its contact point
• Helps protect the porcelain/enamel surface from scratches and chips
• Maintains proper grate alignment over the burner
• Typical symptoms of a failed/missing stud: wobbly or rocking grate, rattling, scuffing around grate landing points

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove the grate and the damaged/missing stud; clean the contact area
• Install the new stud per your model's design and seat it fully without overtightening
• Reinstall the grate and confirm it sits flat and stable

Kit includes 4 pins.

This small end cap fits the end of an extension piece to act as a stop and finish. It restores a secure, finished edge so the sliding component or trim stays aligned and doesn't over-travel during use.

• Caps the end of an extension rail or trim to prevent over-travel and pullout
• Keeps the assembly aligned to reduce wobble
• Replaces cracked, missing, or worn caps
• Helps eliminate rattling and exposed edges

• Disconnect power and allow all hot surfaces to cool before servicing
• Access the end of the extension/rail; release any locking tab and remove the old cap
• Align and snap or press the new cap into place
• Verify smooth travel and a secure stop after installation

This support rod restores stable support and alignment for the designated assembly in your range, helping keep components secure and reducing unwanted movement or sagging over time. What it does:

• Provides rigid support for the attached component or panel
• Replaces a bent, missing, or corroded rod to restore proper fit
• Helps reduce rattling, sagging, or misalignment
• Direct-fit replacement to match the original support geometry

• 1 support rod

• Disconnect power and, if applicable, shut off gas; allow the appliance to cool completely
• Support the related assembly while removing the old rod to prevent dropping
• Transfer any clips or retainers from the original part if present and reinstall in the same orientation
• Secure attachment and clearances before returning the appliance to service

This door opening lever is the replacement release lever that lets the appliance door latch open and close smoothly, restoring reliable door-opening action and making everyday use easier. What it does:

• Replaces a worn, broken, or cracked lever that releases the door latch.
• Lets the door latch release properly so the door opens without excessive force or sticking.
• Works with the latch assembly to help ensure the door closes securely and operates smoothly.
• Addresses common symptoms such as a loose or unresponsive door handle, difficulty opening the door, or a lever that snaps.

• Disconnect power (and water, if applicable) before attempting any repair.
• Access may require removing the door trim or outer panel; basic hand tools are typically needed.
• Inspect surrounding latch components while replacing the lever and replace any damaged hardware.

Main top support rod.

This replacement lever restores a broken or worn lever used to operate the appliance mechanism, letting the related door, latch or control arm move and function properly. It's a direct-fit stamped/plastic lever designed for OEM fit and durable operation. What it does:

• Replaces a cracked, bent or missing lever to restore proper mechanical movement
• Helps re-engage door/latch or control linkage so the appliance can open, close or actuate normally
• Stops grinding, slipping or loose motion caused by a damaged lever
• Fits the original mounting points for straightforward replacement

• One replacement lever

• Install only after unplugging the appliance or switching off power at the breaker
• Verify correct orientation and engage any retaining clips or fasteners fully before testing
• Use basic hand tools; avoid over-tightening fasteners to prevent cracking the lever

This rod-style door switch actuator moves the door-mounted switch striker to signal open/closed door positions, restoring proper door-sensing and interior light functions. It's a small replacement part that helps the appliance detect door position reliably. What it does:

• Engages the door switch when the door closes so the appliance recognizes a closed door
• Allows the interior light to turn on/off based on door position
• Prevents intermittent door-open errors and related operation interruptions
• Works with the door latch/switch assembly to ensure consistent door sensing

• Disconnect power before starting any repair to avoid shock or injury
• Access may require removing the door trim or inner panel—keep fasteners organized
• Align the rod with the switch actuator and door bracket; verify smooth movement before reassembly

This lock lever is the replacement latch arm that engages the oven door lock mechanism so the door secures during self-clean cycles and normal operation. It restores proper door engagement and helps the oven door lock and latch reliably. What it does:

• Moves the latch assembly to secure the door when the lock engages
• Prevents the door from opening during self-clean or locked states
• Common symptom: oven won't enter or complete self-clean because door won't lock
• Common symptom: door feels loose, won't latch, or makes scraping/obstructed noises when closing

• Disconnect power to the appliance before starting any repair
• Access may require removing the oven door or control/front panel; follow OEM instructions
• Handle near edges and glass carefully; use proper tools and keep small fasteners secure