Range Gasket & Seal

This replacement oven door gasket forms the heat-resistant perimeter seal around the door opening. Restores a tight seal to retain heat, support accurate temperatures, and reduce warm-air leakage for better baking performance.

• Creates the compressible seal between the oven cavity and door to keep heat in
• Helps the oven preheat efficiently and maintain even temperatures
• Reduces warm air and odors escaping around the door edge
• Common failure signs include fraying, flattening, gaps, longer preheat, or uneven baking

• Disconnect power and allow the oven to cool completely; wear gloves
• Open the door and remove the old gasket from its retainers/channels, noting clip locations and orientation
• Clean the groove/retainer; starting at the top center, press the new gasket in evenly without stretching and seat corners fully
• Close the door and check for uniform contact around the perimeter

This surface burner seal sits between the burner and the cooktop opening to block spills and air leaks, helping the burner seat correctly and keeping the cooktop area cleaner.

• Creates a tight seal between the surface burner and the cooktop opening
• Helps prevent liquids and debris from getting under the cooktop
• Supports proper burner alignment and consistent heat/flame
• Replace if torn, brittle, swollen, or permanently compressed; common signs include seepage under the top, uneven heating/flame, or the burner not sitting level

• Disconnect power; for gas ranges, also shut off the gas supply. Allow the cooktop to cool completely.
• Remove grates, burner cap, and burner head/base as applicable; lift off the old seal.
• Clean the mating surfaces; position the new seal evenly around the opening.
• Reassemble burner parts and test for proper seating and even heating/flame.

Replacement oven door seal that creates a heat-tight barrier around the oven door to help maintain oven temperature and reduce heat loss. Restores proper door sealing for more even cooking and safer operation. What it does:

• Seals the oven cavity to retain heat and stabilize cooking temperature.
• Helps prevent heat, smoke and odors from escaping the oven during use.
• Replace when the gasket is cracked, flattened, torn, brittle or the oven takes noticeably longer to preheat.
• Improves door closure and can reduce energy loss when installed correctly.

• Disconnect power (and gas if applicable) and allow the oven to fully cool before starting.
• Remove the old gasket per the oven's service instructions; some models require removing the door or loosening fasteners.
• Press the new gasket into the door channel evenly, working around the perimeter so the seal seats flush.
• Wear gloves to protect hands from sharp edges.

Oven door gasket forms the heat seal around the oven door opening to keep heat inside for even cooking and efficient operation. Replaces worn or torn seals to reduce heat loss and improve bake performance. What it does:

• Seals the oven cavity to maintain proper cooking temperature and improve efficiency.
• Helps prevent heat and smoke from escaping around the door.
• Commonly used to address long bake times, uneven cooking, or visible gaps/damage at the door edge.
• Flexible design fits into the door channel to restore a snug seal.

• Disconnect power (and gas supply, for gas ovens) and allow the appliance to fully cool before starting.
• Inspect the door channel and remove old gasket; some models require partial door removal.
• Press the new gasket into the channel evenly; ensure any retaining clips or tabs are fully seated.
• Wear gloves to protect hands from sharp edges and avoid using sharp tools that could damage the new gasket.

This oven door gasket creates a heat-tight seal between the oven door and frame to help retain heat and improve cooking consistency. Replacing a worn gasket reduces heat loss and limits smoke or steam escaping during use. What it does:

• Seals the oven door to help maintain internal temperatures and consistent cooking results.
• Reduces heat and steam leakage that can cause longer cook times or uneven baking.
• Typical signs you need it: visible gaps, flattened or torn seal, or heat/steam escaping from the door.
• Matches OEM fitting style for a direct replace of the damaged or degraded seal.

• Disconnect power to the oven and allow it to cool completely before starting.
• Access the gasket per the manufacturer's guidance—some doors may need to be opened or removed for easier access.
• Remove the old gasket from the channel, then press the new gasket evenly into the channel so it seats fully around the door perimeter.
• Reuse original retainers or hardware; if adhesive or clips are required, follow the oven maker's instructions.

This burner seal is a replacement gasket that fits around a cooktop burner to help keep the burner area sealed and easier to clean. It helps maintain a proper seal between the burner base and the cooktop surface. What it does:

• Seals the gap between the burner and cooktop to limit food, grease and liquid from entering the burner cavity
• Helps keep the burner seated and reduces wobble or misalignment
• Supports cleaner cooktop surfaces and simplifies wipe-downs
• Can help maintain consistent ignition area by keeping debris away from the burner base

• Turn off power to the appliance and ensure the cooktop is completely cool before starting.
• Remove burner grate and lift off the burner cap and burner head as needed to access the seal.
• Clean the seating area of any grease or debris, then press the new seal evenly into place before reassembling.

This door gasket creates an airtight seal around the refrigerator door to help maintain proper cooling and energy efficiency. Replaces a worn, torn or hard-to-close seal to reduce moisture and keep food fresher. What it does:

• Seals the door perimeter to help maintain consistent internal temperatures
• Prevents warm, humid air from entering and forming frost or condensation
• Helps the compressor run less frequently by improving cabinet efficiency
• Reduces drafts, cold spots and premature spoilage caused by a damaged seal

• Clean the door channel and remove old gasket before fitting the new seal
• Warm the gasket with a hair dryer (low setting) if needed to make installation easier

This replacement door gasket seals the refrigerator door to help maintain proper temperature and prevent moisture buildup. A worn or torn seal can cause cooling issues and higher energy use. What it does:

• Creates an air-tight seal around the refrigerator door to help maintain internal temperature
• Reduces frost and moisture buildup by preventing warm, humid air from entering
• Helps improve efficiency and consistent cooling when the original gasket is damaged
• Commonly used when the existing seal is torn, stretched, compressed, or leaving gaps

• Inspect cabinet and gasket channel for debris before installing; clean surface for a proper seal
• Align gasket evenly and press into the channel; some models may require gentle stretching or heating per OEM guidance
• Do not use sharp tools that could nick the gasket; replace if the flange or trim is damaged

Replacement gasket that restores a tight seal to the appliance door and helps prevent water or air leaks. Replaces worn, cracked, or compressed seals so the door closes properly and reduces moisture or heat loss. What it does:

• Seals the door opening to stop leaks of water, steam, or heated air.
• Helps maintain proper temperature and efficiency by preventing air exchange.
• Reduces condensation, odors, and cycling caused by a poor seal.
• Common signs you need this part: visible gaps or damage, leaks around the door, excess moisture, or poor heating/cooling performance.

• Disconnect power and water (if applicable) and allow the appliance to cool before starting.
• Clean and dry the mating surface to ensure a proper fit; remove old adhesive or debris.
• Align the gasket into the door channel or groove and press evenly; avoid stretching the material.
• If the door or mounting hardware is bent or damaged, repair those parts before installing the gasket.

Replacement refrigerator door gasket that restores a tight seal to help maintain proper cooling and reduce frost and moisture buildup. Fits the door channel to stop warm-air leaks and improve overall temperature stability. What it does:

• Seals the refrigerator door perimeter to keep cold air in and warm air out.
• Helps reduce frost and ice buildup inside the compartment.
• Can reduce condensation and uneven cooling caused by a worn or damaged seal.
• Common symptoms of a failing gasket: warm spots, excess frost, visible gaps around the door, or higher-than-normal energy use.

• Unplug the appliance and remove food from the door area before beginning work.
• Clean and dry the gasket channel and door surface; align the gasket and press it fully into the channel for an even seal.
• If the gasket is stiff, gently warming it can make installation easier—avoid excessive heat.
• Confirm this part number matches your appliance model before installing.

This door gasket seals the broiler/bottom-oven door to help retain heat for more even broiling and reduce stray heat into the kitchen. It replaces worn or damaged seals that allow heat loss or uneven cooking. What it does:

• Creates a heat-tight seal around the broiler/bottom-oven door to improve cooking performance
• Helps prevent heat loss, uneven broiling, or extended cook times caused by gaps in the door seal
• Wear signs include visible cracks, flattened or torn material, and gaps around the door edge
• Replacing a damaged gasket can reduce smoke from burning food debris caught in a torn seal

• Disconnect power (and gas, if applicable) and allow the appliance to cool fully before starting
• Remove the broiler drawer or door per the owner's manual to access the gasket channel
• Clean the gasket channel of debris before seating the new gasket; press the gasket into the retainer evenly

This burner seal is a replacement gasket that fits around a surface burner to help keep food and liquids out of the cooktop cavity and make cleanup easier. Simple wear replacement for torn or collapsed seals. What it does:

• Forms a protective gasket between the surface burner and cooktop to limit spills and debris entering the cavity
• Helps keep the burner cap seated correctly and reduces grime buildup around the burner area
• Makes routine cleaning faster by preventing trapped food and liquid
• Common signs you need this part: visible gap or torn seal around the burner, frequent debris buildup, or a burner cap that sits uneven

• Turn off the cooktop and gas supply and allow all parts to fully cool before starting.
• Remove the burner cap and lift out the old seal; align and press the new seal into place around the burner opening.
• Reinstall the burner cap, restore power/gas, and test burner operation for correct seating and appearance.

This burner seal fits the 17k burner to restore a snug seal between the burner and cooktop, helping keep spills out of the burner assembly and keeping the flame properly aligned. Ideal for restoring a cleaner, more reliable cooktop surface. What it does:

• Creates a tight seal around the 17k burner to help prevent food and liquid from entering the burner cavity
• Keeps burner head seated correctly so the flame pattern stays consistent
• Helps reduce soot and residue buildup around the burner area
• Useful when the original seal is cracked, compressed, or missing

• One burner seal for a 17k burner (single piece)

• Always shut off power and gas supply before servicing the range
• Remove burner head and clean mating surfaces before installing the new seal
• Fit the seal in the correct orientation so the burner seats evenly; reassemble parts in reverse order
• After installation, restore power/gas and verify proper burner operation; follow manufacturer's instructions for leak checks and testing

This door gasket seals the refrigerator door to help keep cold air in and warm, humid air out—reducing frost build-up and helping the appliance run more efficiently. Fits where a full perimeter door seal is required. What it does:

• Creates an airtight seal around the refrigerator door to maintain consistent internal temperatures.
• Helps prevent warm air infiltration, moisture, and frost accumulation inside the compartment.
• Reduces energy waste caused by a failing or damaged door seal.
• Common symptoms of a bad seal: condensation at the door, frost on shelves, fluctuating temperatures, or higher energy use.

• Disconnect power to the appliance before attempting any service.
• Remove the old gasket carefully; replacement typically seats into the door channel around the full perimeter.
• Inspect and, if needed, adjust door alignment and hinge condition to ensure a proper seal.

The Seal is an OEM part for Frigidaire ranges. It creates an airtight seal between the oven and cooktop surfaces to contain heat and contain spills. Located around the edges of the oven cavity and cooktop surfaces, the pliable and flexible seal conforms precisely to fit the contours and gaps. 

Symptoms of a bad Range Seal include:

• Excess heat escaping from oven cavity around edges  
• Discolored or melted seal from continuous heat exposure
• Gaps allowing spills to leak underneath surfaces
• Increased energy costs from heat loss

This replacement is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore models.

This foam tape seals and cushions the oven door assembly to reduce vibration and help keep the door glass and inner components stable. It restores proper spacing and helps reduce rattling or light air leaks around the door. What it does:

• Provides a soft, compressible seal between the door and frame to reduce noise and movement
• Cushions and protects glass and trim from contact and vibration
• Helps limit minor air leakage that can allow heat or odors to escape
• Commonly used when door trim or glass is loose, rattling, or shows visible gaps

• One adhesive-backed foam tape strip

• Clean and dry mating surfaces before applying to ensure good adhesive contact
• Measure and trim to fit; press firmly along the full length for proper adhesion
• Replace only with the same style of tape—do not use electrical or non-heat-rated foam in high-temperature areas
• Disconnect power/cool the appliance before working on the door assembly to avoid burns or injury