Range Shaft Or Pin

This small end cap fits the end of an extension piece to act as a stop and finish. It restores a secure, finished edge so the sliding component or trim stays aligned and doesn't over-travel during use.

• Caps the end of an extension rail or trim to prevent over-travel and pullout
• Keeps the assembly aligned to reduce wobble
• Replaces cracked, missing, or worn caps
• Helps eliminate rattling and exposed edges

• Disconnect power and allow all hot surfaces to cool before servicing
• Access the end of the extension/rail; release any locking tab and remove the old cap
• Align and snap or press the new cap into place
• Verify smooth travel and a secure stop after installation

This hinge pin links the oven door hinge to its mounting point, creating the pivot that lets the door open and close smoothly. Replacing a worn or missing pin can restore steady door movement and a consistent seal.

• Serves as the pivot point for the door hinge
• Helps maintain proper door alignment and closing pressure
• Wear or damage may show as a loose, sagging, or misaligned door
• May help address squeaks, binding, or difficulty latching the door

• Disconnect power; for gas ranges, also shut off the gas supply
• Support or remove the door to access the hinge
• Note hinge orientation; remove the old pin and install the new pin securely
• Inspect the hinge/bracket for wear; lubricate only if specified by the manufacturer

This genuine pin hinge secures and guides the appliance door, restoring smooth pivoting and proper alignment for reliable opening and closing. It's a direct-fit replacement designed to help stop door sag, binding, or uneven gaps. What it does:

• Provides the pivot point that lets the door swing open and closed
• Keeps the door aligned to the cabinet for a proper seal and even gap
• Replaces worn or bent pins that cause door sag, scraping, or noisy operation
• Helps restore smooth, wobble-free door motion

• Disconnect power (and water for dishwashers) before starting work
• Support the door during removal to prevent dropping or damage
• Simple hand tools typically required; reuse original screws unless damaged
• If the door has glass or heavy panels, get a helper to hold weight during installation

This brown lock lever is a direct-replacement actuator that engages the appliance's locking mechanism so doors or lids stay securely closed during cycles. Restores proper latch movement and helps the door lock and release as intended. What it does:

• Moves the door/lid latch into the locked or released position when the appliance runs
• Replaces a worn, broken, or bent lever that prevents the lock from engaging
• Helps eliminate symptoms such as a door that won't latch, won't stay closed, or won't unlock at cycle end
• Works as the mechanical interface between the lock assembly and the door/lid

• One brown lock lever (single replacement part)

• Disconnect power and water (if applicable) before servicing to avoid shock or injury
• Access may require removing the control panel or door trim depending on model; follow OEM instructions
• Inspect mating latch and fasteners; replace any damaged clips or screws for secure fit

This door pin secures a door to its hinge assembly so the door opens and closes on a fixed pivot. It replaces a worn or broken hinge pin to restore proper door alignment and movement. What it does

• Acts as the pivot point that lets the door swing smoothly on its hinge.
• Helps keep the door aligned and prevents sagging or off-track movement.
• Commonly replaced when the door falls, binds, or makes grinding noises during operation.
• Small part but critical for maintaining a secure, stable door connection.

• One door pin.

• Disconnect power to the appliance before servicing to avoid electrical or injury risk.
• Remove the door or open it per the manufacturer's service instructions to access the hinge area.
• Use hand tools; keep screws, clips, or washers organized so they are reinstalled in the correct order.
• Handle glass doors and sharp edges with care.

A replacement latch rod that connects and secures the door latch assembly so the appliance door stays closed during use. Restores proper engagement of the latch for safe, reliable operation. What it does

• Links the door latch to the latch mechanism so the door can lock and release correctly
• Helps prevent the door from popping open during operation
• Common fix when the door latch feels loose or the door won't stay closed
• Works with the existing latch assembly to restore normal door function

• One rod-latch

• Disconnect power (or unplug) before starting any repair to avoid electrical or injury risk
• Basic hand tools may be needed; follow the appliance's service manual for access and removal steps
• Inspect the latch and strike for wear; replace any damaged components to ensure proper operation

This broiler pin secures the oven's broiler drawer or rack, letting it slide and lock smoothly for even broiling. Replaces a worn or broken pin to restore proper broiler movement and alignment. What it does:

• Acts as the hinge/anchor for the broiler drawer or rack so it opens and closes smoothly
• Prevents the drawer or rack from sagging, binding, or coming loose
• Helps maintain correct broiler alignment for even heat exposure
• Common symptom: drawer or rack won't slide, sits crooked, or falls out

• Disconnect power (and gas if applicable) and allow the appliance to cool before servicing.
• Remove the broiler drawer or rack per the owner's manual to access the pin.
• This part typically installs by sliding or snapping into a bracket; verify fit before final assembly.