Parts for Kitchenaid KFIS29BBBL00: 04 - Refrigerator Door Parts

Size: 8 x 1-1/4 inch.

Ice clumping or warm dispenser? This refrigerator ice door seals the chute to retain cold air and prevent clumping. Simple DIY fix for damaged doors.

Replace your refrigerator door closer if it's cracked, broken, or missing. This part helps the door close smoothly and securely on your bottom-mount unit.

This door closer secures the appliance door and helps it close smoothly so the unit seals correctly. It restores proper door engagement and reduces gaps that can cause leaks or operation errors. What it does:

• Acts as the door latch/closer to hold the door shut during operation
• Helps the door close smoothly and stay aligned for a tight seal
• Commonly replaces worn or broken closers that prevent the door from latching
• Can resolve symptoms like a door that won't stay closed, won't latch, or closes unevenly

• Disconnect power and any fuel source before beginning work
• Remove the door or access panel per your model's instructions to reach the closer
• Inspect mounting points and strike before installing; align the latch for smooth operation
• Test the door several times after installation to ensure proper engagement and sealing

Refrigerator door mullion rail located between French doors. Replace this structural component if cracked, broken, or damaged to restore door alignment.

Replace cracked or missing door mullion trim to restore your refrigerator's finished look and maintain proper door seal. Confirm fit with your model number.

Vertical center seal between fresh food doors that swings to prevent air leaks and condensation. Replace if warped, cracked, or doors won't seal properly.

This replacement screw fastens appliance components securely in place. Use it to replace missing, stripped, or corroded hardware so panels, brackets, and covers stay aligned and rattle-free.

• Secures parts such as panels, brackets, covers, or internal assemblies
• Restores alignment and helps eliminate vibration or rattling from loose hardware
• Replaces lost, rusted, or damaged screws during service
• Maintains safe, stable operation by keeping components tight

• Disconnect power before service; if applicable, also shut off water and/or gas
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver bit to prevent stripping the head

Replacement door handle for refrigerators. Installs on the exterior door. Needed when original handle is cracked, broken, or worn from use.

Replacement door handle for your refrigerator. Installs on the exterior door surface. Order this part if your original handle is cracked or broken.

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

Cushions and stabilizes your refrigerator door to reduce noise and wear. Replace if cracked, broken, or missing to prevent door slamming and misalignment.

Replace worn or missing door bumpers to cushion your refrigerator door, reduce noise, and prevent metal contact. Restores smooth closing. Verify fit with your model.

Cushions refrigerator door against frame to prevent metal contact. Replace worn or missing bumper to restore smooth closing and protect surfaces from chips.

The Door Handle Mounting Screw is an OEM part for Whirlpool refrigerators. It secures the door handle to the refrigerator door.

Causes of a bad door handle mounting screw can include wear and tear over time, improper installation, or excessive force applied to the handle. These factors can result in a loose or wobbly handle, compromising the functionality and aesthetics of your refrigerator.

Symptoms of a bad door handle mounting screw may include:

• A loose or unstable handle
• Difficulty in opening or closing the refrigerator door
• The handle becoming detached

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

6 - 19 x .250

Seals your refrigerator's ice compartment door to maintain proper temperatures and prevent frost buildup. Replace if ice quality declines or moisture appears.

Secure refrigerator components with this mounting clip. Replace if broken, cracked, or loose to prevent rattling and ensure proper part alignment.

This refrigerator ice level control board monitors ice production and storage levels in your automatic ice maker. It signals when to stop making ice when the bin is full and resume production when ice is needed. Replace this control board when your ice maker overproduces ice, fails to stop when full, or doesn't restart ice production when the bin empties.

This replacement cabinet screw secures panels, brackets, and ducts in Whirlpool-built appliances so components stay aligned and secure. Replacing missing or stripped hardware helps reduce vibration, rattling, and gaps that can affect performance.

• Fastens panels, brackets, and internal components in the appliance cabinet
• Helps maintain proper alignment and reduce vibration or rattling noises
• Restores a tight fit where original hardware is missing, damaged, or stripped
• Typical symptoms: loose paneling, buzzing/rattling sounds, or parts that won't stay fastened

• Disconnect power; for gas models, also shut off the gas supply
• Replace one fastener at a time to preserve alignment and match to the original hardware
• Use the correct driver; start threads by hand to avoid cross-threading
• Do not overtighten into sheet metal

Replacement housing cover that protects internal refrigerator components and wiring. Install if your cover is cracked, broken, or missing.

This slide is the replacement rack glide that helps a rack roll smoothly in and out of the appliance, restoring proper rack movement and preventing scraping or sticking during use. Fits where the factory rack glide has worn or broken. What it does

• Provides a smooth track for a rack to slide in and out without binding
• Replaces cracked, worn or missing glide that causes rubbing or uneven movement
• Helps keep the rack properly aligned during loading and unloading
• Reduces noise and drag from a damaged or missing glide

• One replacement slide/rack glide

• Remove power supply or disconnect appliance before starting any repair
• Access the glide by sliding the rack out and removing any retainer clips or screws as required
• Snap or screw the replacement slide into place and verify smooth rack movement before restoring power
• If other rack parts are damaged, replace them to ensure proper function

Ice maker stopped making ice or won't turn off? This ice level control board monitors bin levels to control ice production. Simple DIY repair.

Fix ice dispenser frost, dripping, or poor ice flow caused by a loose ice chute door. This retainer secures the flapper assembly for a proper seal.

Seals the ice chute opening on your freezer door to block warm air and prevent frost buildup. Replace if ice clumps near dispenser or moisture appears.

Replace your refrigerator's ice dispenser flipper door if cracked, broken, or missing. Installs in the dispenser chute to control ice flow.

Fix ice clumping and frost buildup in your dispenser chute. This flipper spring returns the ice door to closed position, keeping warm air out. Easy DIY fix.

Ice maker not dispensing or flipper assembly loose? This small pin secures the flipper emitter mechanism for reliable ice dispensing. Simple fix.

This replacement water tube restores the appliance's internal water pathway so the dispenser and ice system can receive water. It replaces a cracked or clogged line to stop leaks and restore reliable water flow. What it does:

• Routes water from the inlet to internal components such as the dispenser and ice system
• Prevents leaks when replacing cracked or brittle tubing
• Helps restore water flow when the tube is kinked, clogged, or damaged
• Supports proper ice production and dispenser operation when functioning correctly

• Shut off the water supply and unplug the appliance before starting
• Handle tubing gently to avoid kinks; inspect and replace any worn fittings or seals
• Tighten connections to manufacturer torque recommendations and check for leaks after turning water back on