Remington Log Splitter Parts

The Logsplitter Coupling is a jaw coupling fitted for log splitters. Jaw couplings are flexible couplings that can protect other more sensitive parts from deleterious effects such as heat expansion, vibration, shaft misalignment, and shock loads. The couplings connect two shafts to transmit torque. Jaw couplings are generally used in conjunction with spider bushings. This product is made of durable metal to provide strength while also supporting the alignment of the two connecting shafts. The Logsplitter Coupling is an OEM part sourced directly from the manufacturer and it is sold individually. Spider bushings are sold separately. This piece can be damaged by normal use, in which case it will need to be replaced. A set of socket wrenches, needle nose pliers, and a screwdriver may be necessary during replacement to help install this part correctly. The Coupling-Logsplitt should be connected to the log splitter's engine shaft as well as the hydraulic pump. The part should be attached next to the rear coupling support bracket. The Logsplitter Coupling is compatible for use with log splitters made by MTD, Cub Cadet, Troy-Bilt, and Yard Machines.

This is an authentic OEM replacement .875 coupling for a log splitter. This coupling is used to connect the hydraulic pump shaft and the engine shaft. The engine provides power to the hydraulic pump, which then creates a stream of highly pressurized oil that causes the valve to engage the hydraulic cylinder and split a log. This coupling works in conjunction with a Lovejoy-style rubber spider and .500 coupling. The constant vibrations created by a running engine can wreak havoc on a coupling. Over time, these vibrations can cause the coupling to give out, especially if it is not sized or torqued correctly. Therefore, it is crucial to always check the owner's manual before replacing a part. For safety purposes, be sure to remove the spark plug before disassembling the hydraulic pump. This repair will require a torque driver to tighten the coupling into place. This replacement .875 coupling is a high-quality part sourced directly from its original manufacturer. It is compatible with log splitters made by Huskee, MTD, Troy-Bilt, and Cub Cadet. This part does not include the required .500 coupling or the rubber spider coupling. These parts must be purchased separately.

An authentic OEM replacement extension spring is an integral part of a lawn tractor or snowblowers brake system that helps to hold together and redistribute energy throughout the lower deck. When a driver applies the brakes, the lower deck has a tendency to continue moving forward with inertia. This extension spring helps to keep the parts in place and transfer a balance of energy. Although replacing the extension spring itself is a simple and straightforward process, gaining access to the spring is a little complicated as it requires removing the lawn mower or snowblower's lower deck. You will need a pair of pliers to remove the pins and cables that hold the lower deck in place but there is no other required hardware. Be sure to follow the user's manual as you remove the deck. This part is a top-quality replacement part sourced from its original manufacturer. It is designed to be used with Murray, Husky, Troy-Bilt Poulan, Yard Man, Yard Machines, Bolens, and MTD appliances. This part ships individually.

This lock washer is used frequently for a number of applications on power yard equipment. The size, 5/16, is the default for many small engine housing and manifold applications. Lock washers are used with machined bolts to fasten engine blocks to the housing of the equipment being used. The compressed washer is able to handle the constant vibration of the small gasoline engine without losing the seal between the screw or bolt and the housing. Typically these lock washers only need to be replaced when they are misplaced during repairs or when the screws that attach them have to be chiseled or cut away, meaning the washers are destroyed as well. These OEM certified replacement washers have been manufactured to the same specifications as the originals they are replacing. In addition to lawn mowers, lock washers of this type and size are frequently used on blowers, lawn tractors, cultivators, snowblowers, and trimmers. Brands compatible with this type of washer are Murray, Husky, Poulan, Bolens, Yard-Man, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and Ryobi.

This part is a replacement mandrel bearing. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a defective or broken mandrel bearing in a variety of lawn tractor models. Mandrel bearings are a critical component that ensures no excess heat, friction, or vibration occurs while the equipment is in use. Bearings are subject to wear and tear and will require replacement when no longer working effectively. When working on or near an engine, it's important to ensure that the equipment is powered off and completely cool before beginning any repairs. For more accurate information on how and where to place this mandrel bearing, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this mandrel bearing is suitable for use on lawn tractors manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Please note that this is a genuine part made of high-quality, durable metal and is sold individually.

This carburetor insulator is a genuine MTD replacement part for appliances with small engines, such as lawn mowers, lawn tractors, lawn trimmers, snowblowers, chipper shredders, tillers, and leaf blowers. The purpose of a carburetor insulator is to keep the heat of the running engine away from the carburetor, which combines the air and fuel that ignites the engine. This keeps the engine from overheating and suffering damage as a result.While there is a chance that a damaged carburetor insulator could prevent the engine from igniting altogether, it is more likely that a damaged carburetor insulator will allow for unmetered air leaks into the carburetor. Unmetered air leaks will cause the engine to take in more fuel, reducing the fuel economy of a small engine appliance. For this reason, if the symptoms align with a diagnosis of a damaged carburetor insulator, it must be individually replaced as soon as possible before using the small engine lawn appliance again.This carburetor insulator is compatible with the following brands: MTD, Cub Cadet, Yard Machines, and Craftsman.

This flat washer is used to attach the idler pulley in a number of small and medium sized gasoline powered engines. These engines include snow blowers, log splitters, riding mowers, lawn tractors, and chippers. Because the idler pulley is subject to a great deal of resistance when the pulley is engaged, eventually the pulley will wear out. Should there be a squealing sound when engaging the drive, the problem is likely the idler pulley. In these cases, the pulley must be replaced. It is a good idea to replace the surrounding hardware when replacing the idler pulley; tNhis includes the flat washer, which is subject to corrosion during heavy use. To replace the idler pulley, first detach the spark plug cap. If on a mower or tractor, drop the mower deck. Remove the original pulley and install in order: replacement pulley, hex bolt, flat washer, flange nut. Apart from dropping the mower deck, the only tools required to complete this installation may be a 9/16 ratchet and combination wrench. This washer is a genuine OEM replacement part, designed to perfectly replicate the original piece. This washer is compatible with Troy-Bilt, Yard Man, Yard Machines, MTD, and Craftsman devices.

The lock nut is a piece of standard hardware that may have a variety of applications on lawn and garden equipment, including on engines, housings, and other components. The lock nut offers a secure fit by tightening into a flange that prevents the nut from loosening like a regular nut might. Over time, the flange or the nut can become worn or damaged. In some cases, lock nuts may be lost during the process of other repairs or maintenance. Replacing them with genuine OEM parts like this lock nut is the best solution. This lock nut is compatible with hundreds of machines, including mowers, snowblowers, and chippers from MTD, Troy-Bilt, Cub Cadet, RYOBI, Yard-Man, Yard Machines, Bolens, and Husky. The ¼-inch lock nut has multiple locations and applications, so owners should consult their parts diagram for exact placement and part number identification. This lock nut is made of durable metal and sold as a single unit. Those who need additional pieces will have to order multiple quantities. This part will require a wrench or a socket to replace, as well as pliers and/or a screwdriver to hold the bolt or screw in place.

This fuel tank is a genuine OEM part sourced from the manufacturer. It is commonly used on chippers, lawnmowers, lawn tractors, and other lawn and garden equipment that is powered by gasoline. The fuel tank is attached to the carburetor with a hose and clamp. The fuel tank has a vented fuel cap to help keep a vacuum from developing in the fuel line. If a vacuum develops, the fuel will not flow from the fuel tank to the carburetor. The fuel tank is made of non-corrosive plastic to prevent deterioration from the fuel.Inspect the fuel tank periodically for signs of deterioration. If there are any cracks or flaws that could become cracks, replace the fuel tank. Leaking fuel not only reduces the performance of the engine but can also be a safety hazard. Before replacing the tank, the fuel should be run dry or pumped out. Remove the spark plug to prevent accidental engine ignition while the fuel tank is replaced. This fuel tank is sold as an individual unit. It is designed for use with lawnmowers, lawn tractors, and many other small engines that are powered by fuel. This fuel tank is compatible with equipment made by MTD, Yard Machines, Yard-Man, Cub Cadet, Troy-Bilt, and Husky.

The ignition coil is a standard part of internal combustion engines on lawn and garden equipment. This coil consists of the ignition plug, plastic housing, and metal wires that include a flexible plastic casing. The coil is responsible for connecting the spark plug and transmitting the current that creates the spark that allows the engine to fire. This coil may develop wiring problems or the rubber and plastic parts may become worn and damaged over time. This will require a full replacement of the assembly. It is a good idea to inspect the coil when changing the spark plug as a part of routine maintenance, as well. This genuine OEM ignition coil is compatible with lawn and garden equipment from Troy-Bilt, MTD, Yard Machines, Yard Man, HUSKEE, and Cub Cadet. It can be used on more than 150 lawn and garden machines, including lawn mowers, log splitters, and chipper/shredder models. This coil assembly includes the ignition plug, metal wires encased in plastic, and a plastic housing. The hardware required to install this part is sold separately, as are all other components. Be sure to wear gloves and allow the engine to cool before working on the ignition or other components.

This genuine replacement part is a fuel tank, also known as a fuel tank assembly. This part is the gas tank for a snow blower. This fuel tank holds gas, and is required for proper operation of a snow blower. A faulty or damaged fuel tank can leak gas, leading to improper or dangerous operation of the product. Shut off the snowblower, allow the engine to cool, and ensure the tank is empty before installation. Wear work gloves to protect the hands and work in a well-ventilated area during installation.This high quality OEM replacement part is sourced directly from the manufacturer, and is sold individually. This part is compatible with a variety of MTD, Yard Machines, Troy-Bilt, Yard Man, Cub Cadet, Husky snow blowers. Please note: original part number 751-11201 is now obsolete, and manufacturer has replaced the original part number with this part.

This is a genuine carburetor insulator gasket that is designed to fit select models of lawn mowers. The carburetor insulator gasket is responsible for insulating the carburetor to create a strong seal between it and the engine block and insulate it from the excess heat. This gasket is subject to constant pressure and extreme heat, which can cause it to compress, warp, or become otherwise damaged as a result of regular use. Gaskets should be on the routine maintenance schedule and should be inspected every time other repairs are performed. Without functional gaskets, the engine may run poorly or may not run at all. This genuine OEM carburetor gasket is manufactured by MTD. It can be used in select machines from this brand, as well as those from Troy-Bilt, Cub Cadet, HUSKEE, Yard Man, and Yard Machines. There are hundreds of compatible units that take this gasket. The gasket is made of durable composite materials and sold as an individual unit. Hardware and additional components will require another purchase. Be sure to allow the engine to cool and use the appropriate tools for proper installation without damaging the gasket. Always drain the fuel system before working on the carburetor or internal engine components.

This governor spring is a genuine MTD part, sold individually. This governor spring can be used as a replacement part in lawn mowers, tillers, leaf blowers, log splitters, and wood chippers. The purpose of a governor spring for these outdoor appliances is to facilitate the opening and closing of the throttle which helps the appliance maintain its even pace and speed while in operation.The governor spring in an outdoor appliance might have to be replaced if it loses its spring tension. This could occur as the result of a collision with a hard object or due to general wear and tear over long-term use. If this damage prevents the governor spring from serving its typical function, it should be removed and replaced by this genuine OEM replacement part.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This governor spring is compatible with the following outdoor appliance brands: MTD, Cub Cadet, Craftsman, Troy-Bilt, Yard Machines, Huskee, Yard Man, and MasterCut.

This is an authentic OEM replacement part sourced directly from the manufacturer for use in various small engines. This oil fill tube assembly is part of the oil delivery system. This tube delivers the oil to the oil tank when it is added to the engine. If this tube cracks or deteriorates over time, the oil will not make it to the oil tank or the engine. This could lead to complete engine failure if the leak is not discovered. Oil on the driveway or lawn or smoke coming from under the engine when the lawnmower is running is a sure sign that the tube may need to be replaced.The oil fill tube assembly also houses the dipstick which is used to check the oil level in the mower. If the assembly is leaking, the reading won't be accurate and the lawnmower may be operated without adequate oil which can damage the engine. A screwdriver is needed to replace the oil fill tube. Do not replace this part until the engine has cooled. This oil fill tube assembly is made of black molded plastic and sold as an individual unit. It is designed for use in lawnmowers and other small engines manufactured by Toro, Tecumseh, and Briggs & Stratton.

Here is an OEM replacement fuel cap that can be used with a range of gas-powered lawn and garden machines. The fuel cap is used to protect the fuel tank from debris and dirt. It will also help to reduce air from getting into the fuel tank. If there is air or dirt in the fuel, it can make starting the vehicle more difficult or even impossible. Dirt in the fuel can also cause severe damage to the engine. A replacement cap is a simple fix to prevent these issues. Although fuel caps can last for years, there is always the chance that one could have been lost, damaged, or could suffer from too much wear and tear. The replacement cap can simply be screwed in place to replace the old cap. This is an authentic OEM replacement fuel cap that is sold individually. The cap can be used on many types of machines including tillers, log splitters, chippers, and other small engines. The fuel cap is compatible with many brands including Cub Cadet, MTD, Yard Machines, Yard-Man, and Troy-Bilt.

This part is a carburetor gasket. A carburetor mixes fuel and air before delivering it to the engine. The carburetor gasket creates a seal between the carburetor and cylinder that ensures that air is where it's supposed to be.The carburetor gasket may need to be replaced if the seal is broken and it is allowing air in. If there is a slight leak, the operator may notice engine roughness when it's at idle. A larger leak will cause the engine to vibrate, misfire, or hesitate under acceleration. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer. It it is sold individually. This carburetor gasket is compatible with engines, lawnmowers, log splitters, and trimmers manufactured by MTD, Yard Machines, Yard-Man, Cub Cadet, Husky, and Troy-Bilt.