Remington String Trimmer Parts

Throttle cable for gas line trimmers. Connects carburetor to throttle trigger. Replace if damaged, kinked, frayed, or broken during use.

Replacement reel with pre-wound cutting line for string trimmers. Needed when the original spool is cracked, broken, or worn from regular use.

Lower boom assembly for gas line trimmers. Connects the engine housing to the cutting head. Replace if cracked, bent, or damaged from impact. Essential structural component.

Starter rope won't retract after pulling? This recoil pulley and spring assembly fixes rope retraction issues on mowers and small engines. Direct fit.

This genuine OEM Part is a choke temperature control rod for lawnmowers. The choke temperature control is the metal piece that regulates the choke temperature allowing for it to function properly within a lawnmower. If the choke function is no longer working efficiently, it might be time to replace the choke temperature control. Luckily, replacing this part is a simple repair.Before beginning, make sure the engine is cool to avoid getting burned. Locate the old choke temperature control rod and remove the screws to the mounting assembly that hold the rod in place. Once removed, lift the old choke temperature control out and away from the mower and set it to the side. Replace with the new control rod and secure the mounting screws. Start up the mower to see if the choke function is working properly. If it does, the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

Reel spool assembly for gas line trimmers. Holds and feeds trimmer line during operation. Replace if spool is cracked, worn, or missing components.

Idler bracket assembly for gas line trimmers. Supports the idler arm and maintains proper belt tension. Replace if bent, cracked, or broken.

String keeps spinning at idle or engine overheats? A worn clutch assembly causes engagement issues. This centrifugal clutch repair restores normal operation.

Replace a damaged or worn control cable for your wheeled gas line trimmer. Installs to enable forward propulsion and stopping control functions.

Boom assembly with flexible shaft for gas line trimmers. Connects the engine to the cutting head. Replace if cracked, bent, or worn from impact damage.

Throttle trigger handle for gas line trimmers. Mounts on the main handle shaft to control engine speed. Replace if cracked, broken, or unresponsive.

This is a replacement string trimmer head that is used for a range of makes and models of trimmer. The head, sometimes called a cap, is placed on the bottom of the cutting head assembly. The glide cap is simple, but it serves an important function. It helps to keep the head from contacting the ground, so it is not damaged. The string trimmer head often comes into contact with the ground, roots, concrete, and other materials. Therefore, it can become damaged. It might crack or it could simply start to suffer from normal wear and tear after a lot of use. When this happens, owners should always replace the part sooner rather than later. If it is broken or not functioning properly, it could cause problems with the other elements in the trimmer. The replacement is simple and should not take users more than a few minutes to complete. The replacement string trimmer head is a genuine OEM part and it is sold individually. This part is for use only with string trimmers and is compatible with certain models from MTD and Cub Cadet.

This replacement part is a short block. It is a genuine replacement part made by MTD. A short block is a part that is found inside the engine. It comprises a portion of the cylinder block below the head gasket but above the oil pan. This helps the engine run smoothly overall as well as start and stop the engine efficiently. A new short block might be needed if the user notices that the current one is damaged in any way including being bent, dented, cracked, or chipped. If the user hears unusual noises coming from inside the machine it is possible that the short block is malfunctioning. This can be due to normal wear and tear over time. If this is the case it is recommended that the user replace this part immediately. This is a genuine OEM replacement part. This short block is sold individually and is sourced directly from the manufacturer.

Idler pulley for wheeled trimmers. Maintains belt tension in the drive system. Replace if pulley is cracked, worn, or spins roughly on bearing.