Remington String Trimmer Parts

Blade guard assembly for line trimmers. Protects operator from debris and rotating components. Replace if cracked, broken, or missing for safe operation.

This is a gear box assembly that is a part of many types of gasoline-powered string trimmers. The gear box assembly is attached to the lower boom assembly. The purpose of the component is to spin and drive the trimmer head to cut through weeds and grass. The gear box assembly is attached to the string trimmer by two screws. This assembly comes with a trimmer head.If the gear box assembly has been damaged and needs to be replaced, a screwdriver will be needed. Place the string trimmer on a level surface and disconnect the spark plug wire for safety. Use a screwdriver to remove the screws from the old gear box assembly so it can be taken off. Use new screws to install the replacement component. Retighten the screws before use.This is an authentic OEM replacement component that is sourced directly from the manufacturer. It is sold as an individual part. The gear box assembly is designed to be used with string trimmers manufactured by MTD, Bolens, and Yard Machines.

Engine o-ring gasket creates a compression seal between engine components to prevent oil and fluid leaks. Replace when worn or cracked. Verify fit with your model.

O-ring gasket creates a seal to prevent fluid and gas leaks in tillers and lawn equipment. Replace when cracked, brittle, or leaking. Verify fit.

Throttle cable for gas line trimmers. Connects carburetor to throttle trigger. Replace if damaged, kinked, frayed, or broken during use.

This is a quality rear engine cover that is used on several types of string trimmers. The component is tightened onto the back of the trimer to offer protection and shielding to the engine. It is made of a durable material and comes with both the cover and four screws to attach it to a string trimmer. Over time, the rear engine cover can become damaged, broken, or lost and should be replaced to ensure the engine is protected.Check the rear engine cover for cracks and other damage before installing a new replacement part. First, remove the screws from the rear engine cover so it can be taken off of the string trimmer. An O-ring may be needed to create the proper clearance when installing the new rear engine cover. Make sure to properly tighten the screws on the cover before use.This rear engine cover is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual component. The engine cover is designed to be compatible with string trimmers manufactured by Bolens, MTD, Yard Machines, Murray, and Craftsman.

Flywheel assembly for gas leaf blowers and line trimmers. Mounts to the engine crankshaft. Replace if cracked, damaged, or missing flywheel fins.

Ignition coil module assembly for gas string trimmers. Mounts to engine block and connects to spark plug. Replace if cracked, damaged, or contacts are worn.

Ignition module for gas leaf blowers and line trimmers. Mounts to the engine to control spark timing. Replace if cracked, damaged, or missing.

Replacement reel with pre-wound cutting line for string trimmers. Needed when the original spool is cracked, broken, or worn from regular use.

Replacement fuel cap for gas trimmers and handheld lawn tools. Seals the fuel tank to keep dirt and debris out. Replace if cracked, missing, or worn.

Lower boom assembly for gas line trimmers. Connects the engine housing to the cutting head. Replace if cracked, bent, or damaged from impact. Essential structural component.

Inner spool reel for line trimmers. Holds and winds trimmer string inside the trimmer head. Replace if cracked, broken, or worn from use.

Replacement throttle trigger spring for gas line trimmers. Installs inside the throttle trigger assembly. Needed when original spring is broken or missing.

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.