Electrolux Washer won't spin: Common Causes & How to Fix

Repair Instructions:

A top-load Electrolux washer tub is usually held up by four suspension rods. When one of these rods gets dislodged or breaks, the control board might pause the spin cycle multiple times in an attempt to balance the clothes properly. It's often advised to replace all four suspension rods together as a set. This helps prevent uneven wear and makes sure the Electrolux washer functions smoothly.

How to Replace Washing Machine Suspension Rod

1. Unplug the washing machine from the power source. This ensures the washing machine will not start during the repair.

2. Tip the washing machine back. Carefully tip the washing machine back to access the bottom panel. You may need assistance to prevent the machine from tipping over.

3. Remove the bottom panel. The bottom panel is usually held in place by screws along the bottom edge. Use a screwdriver to remove the screws and detach the panel.

4. Locate the suspension rod. The rod will extend from the washing machine tub to the base. Identify which suspension rod needs replacing.

5. Remove the retaining clips. Use pliers to detach the retaining clips or rings holding the suspension rod in place.

6. Slide out the old rod. Carefully slide out the old rod from the washing machine tub and base. You may need to wiggle it side to side to detach it.

7. Install the new rod. Slide the new suspension rod into place, inserting it into the tub and base.

8. Secure with retaining clips. Reattach any retaining clips or rings to hold the new rod firmly in place.

9. Replace the bottom panel. Line up the bottom panel and screw it back into place along the bottom edge.

10. Return the washing machine to upright position. Carefully tip the washing machine back to an upright position.

11. Plug washing machine back in. Reconnect the power source so the washing machine is ready to use.

12. Test it out. Run a test cycle with no clothes to verify the washing machine is functioning properly before using again.

Repair Instructions:

Check the drive belt to see if it is broken or if it has become loose on the pulleys. If you find that the drive belt is either broken or loose, it needs to be replaced.

How to Replace Washing Machine Drive Belt

1. Unplug the washing machine. Disconnect the power cord for safety.

2. Access the belt. Remove the back service panel to access the motor and belt assembly.

3. Locate the belt. Identify the rubber drive belt that connects the motor pulley to the drive pulley.

4. Loosen motor mount. Use a wrench to loosen the bolts on the motor mounting bracket.

5. Remove old belt. Slip the old belt off the motor and drive pulleys. You may need to pivot the motor to get slack in the belt.

6. Install new belt. Loop the new belt around the pulleys, ensuring it is properly seated in the grooves.

7. Retighten motor. Tighten bolts on motor mount bracket to secure in place.

8. Reattach service panel. Replace the back service panel.

9. Restore power. Plug washing machine back in.

10. Test operation. Run a short test cycle with no clothes to verify smooth operation.

11. Adjust belt tension. If the belt is loose, pivot motor slightly to increase tension and prevent slipping.

Repair Instructions:

The lid switch assembly is responsible for stopping the Electrolux washer from spinning when the lid is open. If this assembly fails, the Electrolux washer will not spin. To check if the lid switch assembly is the problem, you can use a multimeter to test the continuity of the lid switch. If the lid switch does not show continuity, it means it is not working properly and should be replaced.

How to Replace Washing Machine Lid Switch Assembly

1. Unplug the washing machine. Disconnect the machine from the power source. This will prevent electric shock.

2. Open the lid. Prop the washing machine lid fully open.

3. Locate the switch. The lid switch assembly is on the front panel of the Electrolux washer. Identify the specific location.

4. Remove switch mounting screws. Use a screwdriver to detach any screws securing the switch assembly.

5. Disconnect wiring. Carefully disconnect the wiring harness or connectors attached to the switch.

6. Remove switch assembly. With the screws and wiring detached, you can now fully remove the lid switch assembly.

7. Install new switch. Carefully align the new lid switch assembly into the opening on the Electrolux washer front panel.

8. Reconnect wiring. Attach the wiring harness or connectors to the corresponding terminals on the new switch.

9. Remount the switch. Insert and tighten the mounting screws to secure the new lid switch assembly in place.

10. Test operation. Plug in the Electrolux washer and open/close the lid to verify proper switch operation before regular use.

11. Reattach panel. If accessing from inside the cabinet, reattach the metal panel covering the lid switch assembly.

12. Restore power. Plug the washing machine back in and make sure it is functioning properly.

Repair Instructions:

The motor coupling is what links the motor to the washing machine transmission. When the Electrolux washer is overloaded, the motor coupling is designed to fail in order to safeguard both the motor and transmission. Additionally, the motor coupling can wear out over time and cause failure. To check if the motor coupling is broken, examine it closely. If you find that the motor coupling is indeed broken, it should be replaced.

How to Replace Washing Machine Motor Coupling

1. Unplug the washing machine. Disconnect the power cord before servicing.

2. Access the motor. Remove the back service panel to access the motor.

3. Locate the motor coupling. Identify the rubber motor coupling that connects the motor to the drive transmission.

4. Remove mounting hardware. Use a socket wrench to detach any mounting bolts or nuts on the motor and transmission shafts.

5. Separate the coupling. With the hardware removed, the rubber coupling should detach from the motor and transmission shafts.

6. Install new coupling. Slide the new rubber coupling onto the shafts, aligning the shafts inside the coupling.

7. Replace mounting hardware. Reattach the bolts or nuts to secure the coupling in place between the motor and transmission.

8. Reattach service panel. Replace the back service panel covering the motor.

9. Restore power. Plug washing machine back in and verify proper operation.

10. Test operation. Run a short test cycle with no clothes to confirm smooth running before regular use.

11. Tighten if needed. If excessive vibration, tighten mounting bolts to better align motor and transmission shafts.

Repair Instructions:

The washing machine control board is responsible for supplying power to most of the electrical parts in the Electrolux washer. If the control board is faulty, it may fail to send power to the drive motor when the spin cycle is running. To check if the control board is the issue, you can examine it for any signs of burning or damaged components. Additionally, you can use a multimeter to test the power output terminals on the board, following the appliance's wiring diagram as a guide.

How to Replace Washing Machine Control Board

1. Unplug the washing machine. Disconnect the power cord before servicing to prevent electric shock.

2. Open the control panel. The control board is located behind the control panel on the Electrolux washer front.

3. Label connections. Take note of where each wire and connector is attached to the control board.

4. Disconnect wires. Carefully detach all wiring harnesses and connectors from the board.

5. Remove mounting screws. Use a screwdriver to remove any screws securing the control board.

6. Remove control board. Carefully pull the control board free from the Electrolux washer once all wires are detached.

7. Install new control board. Align the replacement board into position and insert mounting screws.

8. Reconnect wires. Attach all wiring harnesses and connectors to the matching terminals on the new board.

9. Close control panel. Carefully close the control panel once the new board is installed.

10. Restore power. Plug in the washing machine and test operation.

11. Program control board. You may need to program or configure the new control board if it doesn't operate correctly.

12. Test cycles. Run short test cycles to verify the Electrolux washer is functioning properly before regular use.

Repair Instructions:

The stator and rotor work together to generate a powerful electromagnetic field that spins the tub in either direction. If the windings on the stator are damaged, the Electrolux washer will not spin or agitate properly. To identify if the stator is the issue, carefully examine it for any signs of damaged windings or other defects.

How to Replace Washing Machine Stator Assembly

1. Unplug the washing machine. Disconnect power to prevent electric shock.

2. Access the stator. Remove the back service panel to access the stator assembly.

3. Disconnect wiring. Detach the wiring harness leads from the stator windings.

4. Loosen mounting bolts. Use a socket wrench to loosen the bolts securing the stator.

5. Remove stator. Carefully detach the old stator assembly from the outer tub.

6. Install new stator. Align and mount the new stator assembly against the outer tub.

7. Tighten mounting bolts. Tighten the mounting bolts securely with a socket wrench.

8. Reconnect wiring. Attach the wiring harness leads to the terminals on the new stator.

9. Replace service panel. Reattach the back service panel.

10. Restore power. Plug in the washing machine.

11. Test operation. Verify proper functioning by running a test cycle.

12. Troubleshoot issues. If problem persists, check wiring connections on stator.

Repair Instructions:

The drive pulley is the part that connects to the Electrolux washer drum and, together with the drive belt and motor, helps rotate the drum. When the drive pulley becomes worn out, the drive belt can slip off, which stops the Electrolux washer from spinning. To address this issue, you can remove the drive pulley and examine it closely. If you find that the drive pulley is not working properly, it should be replaced.

How to Replace Washing Machine Drive Pulley

1. Unplug the washing machine. Disconnect power to avoid electric shock.

2. Access the pulley. Remove the back service panel to locate the drive pulley.

3. Loosen set screw. Use an Allen wrench to loosen the set screw securing the pulley to the drive shaft.

4. Remove pulley. Slide the old pulley off the drive shaft. You may need a pulley puller tool.

5. Clean shaft. Remove any oil, dirt or debris from the drive shaft.

6. Install new pulley. Slide the new pulley onto the drive shaft until fully seated.

7. Tighten set screw. Tighten the set screw against the flat of the drive shaft to secure.

8. Check alignment. Make sure the pulley is properly aligned with the motor pulley.

9. Replace service panel. Reattach the back service panel.

10. Restore power. Plug washing machine back in and test operation.

11. Test spin cycle. Verify smooth rotation when running a spin cycle with no load.

Repair Instructions:

The washing machine control board is an important part that supplies power to most of the electrical components in the Electrolux washer. If the control board is defective, it may not send power to the drive motor during the spin cycle. To check if the control board is the issue, you can examine it for signs of burning or any components that may be shorted out. Additionally, you can use a multimeter to test the power output terminals on the board, following the appliance's wiring diagram as a guide.

How to Replace Washing Machine Main Control Board

1. Unplug the washing machine. Disconnect power to prevent electric shock.

2. Open control panel. Unscrew the control panel on the Electrolux washer to access interior.

3. Locate control board. The main control board is mounted to the cabinet interior.

4. Label wire connections. Note where each wire harness connects to the control board.

5. Disconnect wires. Detach all wire harnesses from the terminals on the control board.

6. Remove mounting screws. Use a screwdriver to remove screws securing control board.

7. Remove control board. Carefully detach old control board from the Electrolux washer.

8. Install new control board. Align replacement board and reinsert mounting screws.

9. Reconnect wires. Attach all wire harnesses to proper terminals on new control board.

10. Close control panel. Carefully close and screw the control panel back on.

11. Restore power. Plug in washing machine and test operation.

12. Program control board. You may need to program the new control board if needed.

Repair Instructions:

The rotor and stator work together to generate a powerful electromagnetic field that spins the tub in either direction. However, if the magnets on the rotor are damaged or any part of the rotor is faulty, the Electrolux washer may fail to spin or agitate properly. To check if the rotor is the problem, examine it closely for any signs of damage. If you find that the rotor is indeed damaged, it should be replaced with a new one.

How to Replace Washing Machine Rotor Assembly

1. Prepare for the replacement: Gather all the necessary tools and equipment before starting the replacement process. You will typically need a wrench, pliers, screwdriver, and a replacement rotor assembly that matches your washing machine's make and model. Make sure that the washing machine is unplugged and disconnected from any power source.

2. Access the rotor assembly: The rotor assembly is usually located at the back of the washing machine, behind the drum. Begin by removing the access panel on the back of the machine. Refer to the manufacturer's instructions or the washing machine's manual for specific guidance on accessing the rotor assembly.

3. Disconnect the wiring: Locate the wiring harness that connects the rotor assembly to the washing machine's electrical system. Carefully disconnect the wiring by gently pulling apart the connectors. Take note of the positions or colors of the wires to ensure proper reconnection later.

4. Remove the rotor assembly: Once the wiring is disconnected, use a wrench or pliers to loosen and remove the bolts or screws that secure the rotor assembly in place. Set aside the fasteners in a safe location. With the fasteners removed, gently pull the rotor assembly away from the machine, disengaging it from the drive shaft.

5. Install the new rotor assembly: Take the replacement rotor assembly and align it with the drive shaft. Make sure that it fits snugly into place. Use the previously removed bolts or screws to secure the new rotor assembly to the washing machine. Tighten them firmly but avoid over-tightening, as it may damage the components.

6. Reconnect the wiring: Reconnect the wiring harness to the corresponding connectors on the new rotor assembly. Match the wire positions or colors as noted earlier to ensure correct alignment. Make sure the connections are secure and properly seated.

7. Replace the access panel: Once the new rotor assembly is installed and the wiring is reconnected, reattach the access panel on the back of the washing machine. Align it properly and secure it with the appropriate screws or fasteners.

8. Test the washing machine: Plug the washing machine back into the power source and conduct a test run to ensure that the new rotor assembly is functioning correctly. Run a cycle and listen for any unusual noises or vibrations. Monitor the machine's performance to verify that the replacement was successful.

9. Clean up and dispose of old parts: Dispose of the old rotor assembly and any other replaced parts responsibly. If the old parts are recyclable, consider taking them to a recycling center. Clean up your work area and store your tools properly.

Repair Instructions:

The tub bearing is mounted in the middle of the outer tub of the washing machine. Its purpose is to make sure the inner tub spins smoothly. If the tub bearing is faulty, it can cause the Electrolux washer to become stuck and prevent spinning. Additionally, you may hear a loud rumbling noise. Repairing the tub bearing is a complex task that involves disassembling most of the Electrolux washer. If the tub bearing is indeed defective, we recommend replacing both the outer tub and bearing together as a single unit.

How to Replace Washing Machine Tub Bearing

1. Prepare for the replacement: Before starting the replacement process, gather the necessary tools and equipment. You will typically need a wrench, pliers, a screwdriver, and a replacement tub bearing kit that is compatible with your specific washing machine model. Make sure that the washing machine is unplugged and disconnected from any power source.

2. Access the tub bearing: The tub bearing is located inside the washing machine's tub assembly. To access it, you will need to disassemble the washing machine. Refer to the manufacturer's instructions or the washing machine's manual for specific guidance on accessing the tub bearing.

3. Remove the outer tub: Begin by removing the agitator and any other components that obstruct access to the outer tub. Use a wrench or pliers to disconnect the hoses and any other connections attached to the tub. Once all connections are detached, carefully lift and remove the outer tub from the washing machine.

4. Remove the old tub bearing: Locate the old tub bearing inside the tub assembly. It is typically secured with bolts or screws. Use a wrench or screwdriver to loosen and remove these fasteners. Once the fasteners are removed, carefully pull out the old tub bearing from its position.

5. Install the new tub bearing: Take the replacement tub bearing from the kit and align it with the opening in the tub assembly. Make sure that it fits snugly into place. Use the provided bolts or screws to secure the new tub bearing to the tub assembly. Tighten them firmly but avoid over-tightening.

6. Reassemble the outer tub: Carefully place the outer tub back into the washing machine. Reconnect the hoses and any other connections that were detached earlier. Ensure that all connections are secure and properly tightened.

7. Reassemble the remaining components: Reattach the agitator and any other components that were removed to access the tub bearing. Follow the manufacturer's instructions or the washing machine's manual for proper reassembly.

8. Test the washing machine: Plug the washing machine back into the power source and run a test cycle to ensure that the new tub bearing is functioning correctly. Monitor the machine for any unusual noises or vibrations that may indicate a faulty installation. Make sure that the tub spins smoothly and without hindrance.

9. Clean up and dispose of old parts: Dispose of the old tub bearing and any other replaced parts responsibly. If the old parts are recyclable, consider taking them to a recycling center. Clean up your work area and store your tools properly.

Repair Instructions:

The tub bearing and seal are located in the middle of the outer tub of the washing machine. Their role is to make sure the inner tub spins smoothly. However, if the tub bearing is faulty, it can cause the Electrolux washer to become stuck and prevent spinning. Additionally, you may hear a loud rumbling noise. Repairing the tub bearing and seal is a complex task that involves disassembling most of the Electrolux washer. If the tub bearing is indeed defective, we recommend replacing both the outer tub and bearing together.

How to Replace Washing Machine Tub Seal and Bearing Kit

1. Prepare for the replacement: Gather all the necessary tools and equipment before starting the replacement process. You will typically need a wrench, pliers, a screwdriver, and a replacement tub seal and bearing kit that matches your washing machine's make and model. Make sure that the washing machine is unplugged and disconnected from any power source.

2. Access the tub seal and bearing: The tub seal and bearing are located inside the washing machine's tub assembly. To access them, you will need to disassemble the washing machine. Refer to the manufacturer's instructions or the washing machine's manual for specific guidance on accessing the tub seal and bearing.

3. Remove the outer tub: Begin by removing any components that obstruct access to the outer tub, such as the agitator and any other attachments. Disconnect the hoses and any other connections attached to the tub using a wrench or pliers. Once all connections are detached, carefully lift and remove the outer tub from the washing machine.

4. Remove the old tub seal and bearing: Locate the tub seal and bearing assembly inside the tub assembly. It is typically secured with bolts or screws. Use a wrench or screwdriver to loosen and remove these fasteners. Once the fasteners are removed, carefully separate the old tub seal and bearing assembly from the tub.

5. Install the new tub seal and bearing: Take the replacement tub seal and bearing kit and align it with the opening in the tub assembly. Ensure that it fits properly into place. Follow the manufacturer's instructions or the kit's guidelines for proper installation. This usually involves inserting the new tub seal and bearing assembly and securing it with the provided bolts or screws.

6. Reassemble the outer tub: Carefully place the outer tub back into the washing machine. Reconnect the hoses and any other connections that were detached earlier. Make sure that all connections are secure and properly tightened.

7. Reassemble the remaining components: Reattach the agitator and any other components that were removed to access the tub seal and bearing. Follow the manufacturer's instructions or the washing machine's manual for proper reassembly.

8. Test the washing machine: Plug the washing machine back into the power source and run a test cycle to ensure that the new tub seal and bearing assembly is functioning correctly. Monitor the machine for any unusual noises or leaks that may indicate a faulty installation. Make sure that the tub spins smoothly and without hindrance.

9. Clean up and dispose of old parts: Dispose of the old tub seal and bearing assembly and any other replaced parts responsibly. If the old parts are recyclable, consider taking them to a recycling center. Clean up your work area and store your tools properly.

Repair Instructions:

The washing machine drain pump plays an important role in removing water from the tub by pushing it through a drain hose to a laundry tub or drain pipe. As water needs to be drained multiple times during a wash cycle, a faulty drain pump can disrupt the operation and prevent the tub from spinning during the spin cycle. If you find that there is still water in the tub after the Electrolux washer stops, it is important to examine the drain pump for any blockages. Additionally, you can use a multimeter to test the drain pump for electrical continuity, which helps determine if the pump is functioning properly or not.

How to Replace Washing Machine Drain Pump

1. Unplug washing machine. Locate the plug on the back of the machine and disconnect from power source to prevent electric shock.

2. Remove access panel. Find panel that provides access to internal components, usually on the bottom front of the machine. Lift panel off after removing any retaining screws.
3. Disconnect drain hose. Detach hose from old pump and drain remaining water from hose into a bucket. Apply clamp if needed to prevent additional water escaping.
4. Remove retaining bolts. Identify and loosen bolts or screws securing pump in place using appropriate tool like screwdriver or wrench.
5. Remove old pump. Slide out old pump taking care not to damage surrounding components. Check area for any worn Electrolux washers or seals in need of replacement as well.
6. Install new pump. Line up and insert replacement pump into location. Secure with the retaining bolts removed earlier.
7. Reconnect drain hose. Attach drain hose to new pump outlet, push firmly into place.
8. Replace access panel. Position panel over opening and secure with any screws.
9. Test operation. Reconnect power and run short cycle without laundry to check for leaks from connections. Fix any issues before regular use.

Repair Instructions:

The rear drum of the Electrolux washer contains bearings that are responsible for keeping the inner tub spinning smoothly. When there is a problem with the tub bearing system, the Electrolux washer can make a lot of noise and the tub may stop spinning. In some cases, the bearings can be purchased separately from the rear drum. However, we suggest replacing both the outer drum and bearing together as a unit if the manufacturer provides them as a set. This is because installing a new bearing can be extremely challenging. It's important to note that replacing the outer tub and bearing is a difficult task and can be quite expensive.

How to Replace Washing Machine Rear Drum with Bearing

1. Remove old drum. Disconnect power to washing machine. Remove access panel and any mounting bolts or belts securing drum. Carefully pull out drum from machine.

2. Inspect drum bearing. Check bearing for signs of wear or damage. Spin smoothly? Replace if noisy or rough.

3. Clean drum area. Wipe away any debris from where drum sits with a dry cloth. Inspect drum mount area for cracks or damage and repair/replace as needed.

4. Install new bearing if needed. Press or slide new bearing into rear drum mount, with grease applied if recommended.

5. Install new drum. Position replacement drum into machine shell aligning mounts. Secure with bolts while checking for play.

6. Refit access panel. Replace any removed panels and secure with fasteners.

7. Reconnect power and test. Plug machine back in and run empty drum spin cycle to check for noise or vibration issues. Repair as required before use.

Repair Instructions:

The bearing is located in the middle of the outer tub and is responsible for making sure the inner tub spins smoothly. If the tub bearing is faulty and can be purchased separately, it should be replaced. If the bearing is not available as a separate component, it is recommended to replace both the outer tub and bearing together. It's important to note that replacing the outer tub and bearing is a challenging and expensive repair. If the bearing is defective and the cost of repair is significant, it may be worth considering replacing the entire washing machine instead.

How to Replace Washing Machine Bearing

1. Unplug machine and remove access panel. Disconnect power and remove any rear/bottom panels to access internal components.

2. Detach cabling and belts. Remove any wiring, hoses or drive belts connected to the old bearing. Note positions for reinstallation.

3. Remove retaining bolts. Using appropriate tools, loosen and remove bolts or screws securing the bearing housing in place.

4. Detach bearing housing. Gently separate the bearing housing from surrounding parts. You may need to maneuver or tap to release seal friction.

5. Extract old bearing. Pull out the old bearing taking note of orientation. Inspect seal/ Electrolux washers for wear. Clean housing area.

6. Pack new bearing. Grease the inner and outer bearing surfaces if recommended.

7. Install new bearing. Carefully slide replacement bearing into correct position using opposite of removal process.

8. Refit housing. Align housing and push/tap into place, reusing original seals if possible. Refit retaining bolts.

9. Reconnect components. Attach any cables/belts removed earlier and refit access panels.

10. Test machine. Run empty cycle to check for noise or issues. Repair as needed before regular use.

Repair Instructions:

The damper in a washing machine limits drum movement and maintains balance during the wash cycle. If a damper is faulty or broken, it can cause the tub to become unbalanced, preventing spinning. Visually inspect dampers for cracks or damage, and observe drum movement during operation to check for proper centering. If a damper is defective, it will need to be replaced.

How to Replace Washing Machine Damper

1. Unplug Electrolux washer and open access panel. Disconnect power and remove rear or bottom panel to access internal components.

2. Detach drain hose from damper. Remove any clips securing hose and pull hose off old damper.

3. Remove mounting bolts. Using appropriate tools, loosen and remove all bolts securing damper housing in place.

4. Detach damping springs. Use pliers to grasp and gently remove damper springs from housing lugs and tube. Note orientation.

5. Extract old damper. Ease damper housing out of position, wiggling as needed. Remove damper blade and housing as one piece if possible.

6. Clean housing mating area. Wipe away debris from inner rim where damper housing sits using dry cloth.

7. Fit new damper springs. Attach replacement damping springs onto lugs in correct position mirroring old installation.

8. Install new damper housing. Push housing into place, aligning bolt holes. Refit mounting bolts.

9. Attach drain hose. Push drain hose firmly onto new damper outlet, secure with clips.

10. Test operation. Run empty cycle and check damper blade movement and drain flow are unrestricted before use.

Repair Instructions:

Before deciding to replace the drive motor, it's important to check other Electrolux washer parts that are more likely to be the problem. If none of those parts are defective, then you can consider replacing the drive motor. To find out if the drive motor is indeed faulty, start by making sure that it is receiving power. If the drive motor makes a humming sound but doesn't run, is noisy, or doesn't turn easily, then it should be replaced.

How to Replace Washing Machine Drive Motor

1. Unplug Electrolux washer and secure access. Disconnect power and open rear or bottom panel for protected access.

2. Detach drive belt. Remove belt over pulleys attached to motor and drum. Note routing for replacement.

3. Disconnect wiring. Unplug electrical connections to motor, noting wire colors/positions.

4. Loosen mounting hardware. Remove screws or bolts attaching motor to inner chassis.

5. Manoeuvre out old motor. Gently ease motor from supports, wiggling as required. Check mounting point for wear.

6. Clean mount area. Wipe away debris where new motor will sit using dry cloth.

7. Fit replacement motor. Carefully slide motor into position, aligning mounts. Refit hardware.

8. Refit wiring. Reconnect electrical plugs to new motor ports in reverse of removal.

9. Replace drive belt. Route replacement belt correctly over pulleys.

10. Test operation. Run empty cycle and check for unusual noise before regular use. Troubleshoot as needed.

Repair Instructions:

The basket drive is located on top of the transmission and connects with the inner tub. If you notice that the transmission is engaged and spinning, but the outer tub is spinning slowly or not spinning at all, it's possible that the spin tube tabs or the drive block on the spin tube are stripped. Take a look at both the spin tube tabs and the drive block to inspect them for any signs of wear. If neither of them is worn out, it's likely that the clutch pads on the basket drive have become worn out. In this case, you will need to replace the basket drive.

How to Replace Washing Machine Basket Drive

1. Unplug machine and open access panel. Disconnect power and remove rear/bottom panels for safe access.

2. Remove drive belt. Use a tool to slip belt off motor and basket drive pulleys.

3. Disconnect wiring. Unplug any electrical connections from drive circuit board.

4. Loosen mounting bolts. Using appropriate tools, remove bolts securing drive assembly in place.

5. Detach drive assembly. Carefully maneuver drive unit from mounts, wiggling as needed.

6. Inspect basket gear. Check gear teeth and spindle for excessive wear before replacement.

7. Clean mounting area. Wipe away debris from where new drive will sit using dry cloth.

8. Install replacement drive. Set drive in position and start mounting bolts by hand to avoid cross-threading.

9. Refit wiring connections. Plug in electrical plugs removed earlier.

10. Replace drive belt. Route new belt correctly over pulleys tensioning as per manual.

11. Test operation. Run empty cycle and check smooth basket movement before clothes loads.

Repair Instructions:

The door strike, also known as the door catch, is an important part of a front-load Electrolux washer. It is responsible for locking the door securely. The door strike has two pins that activate the door switch when the door is closed. If your Electrolux washer is not spinning, a possible reason is a damaged door strike, which prevents the door from locking properly. To check the door strike, locate it inside the Electrolux washer door and inspect it for damage or wear. If you find any problems, it is recommended to replace the door strike. A damaged or worn-out door strike can affect the functioning of the door lock, causing spinning issues. Replacing the door strike with a new one will make sure that the door is securely locked during operation, allowing the Electrolux washer to work properly.

How to Replace Washing Machine Door Strike

1. Open washing machine door. Make sure door opens smoothly without obstructions.

2. Locate door strike. This is the metal tab or latch inside the machine that the door catches on.

3. Remove any retaining screws. Use correct screwdriver or tool to undo screws or bolts holding strike assembly in place.

4. Detach old strike. Ease old strike out of housing, wiggling or prying gently if stuck.

5. Inspect strike housing. Check for cracks, corrosion or worn areas that could affect new strike performance.

6. Clean housing area. Wipe away debris from housing interior where replacement strike will sit.

7. Position new strike. Align tabs on new strike with holes in housing.

8. Refit retaining screws. Hand-tighten screws to hold new strike without over tightening.

9. Check door closure. Close door and ensure it latches securely on strike without issues.

10. Test machine operation. Run empty cycle and check for leaks or vibrations before regular use.

Repair Instructions:

The Electrolux washer transmission could be worn out or faulty. Transmissions contain gears that can fail, resulting in the Electrolux washer not spinning. It is highly unlikely that the transmission is the cause of the problem. Before considering a transmission replacement, it is important to check all the other parts that are more commonly associated with defects or issues.

How to Replace Washing Machine Transmission

1. Unplug machine and open panels. Disconnect power and remove rear/bottom access panels for protected internal access.

2. Detach transmission belt. Remove belt from motor pulley and any transmission pulleys it engages.

3. Disconnect wiring harnesses. Unplug any electrical plugs connected to transmission controls.

4. Loosen mounting hardware. Remove retaining bolts or screws securing transmission to machine frame.

5. Extract transmission assembly. Ease transmission from mounts, wiggling side-to-side if stuck. Take care not to damage parts.

6. Clean transmission area. Wipe away debris from mounts where new unit will sit using dry cloth.

7. Install replacement transmission. Line up mounting holes and hand-start bolts to avoid cross-threading.

8. Reconnect wiring harnesses. Plug in any electrical connections removed earlier.

9. Replace transmission belt. Route belt correctly over pulleys, tensioning as per machine specifications.

10. Test operation. Run empty cycle and check for unusual noises before using for clothes washing.

Repair Instructions:

The door lock, also known as the interlock, is an important safety feature found on front-loading washing machines and some top-load Electrolux washers. It plays a vital role in preventing the door from being opened while the machine is running, ensuring user safety. This system consists of a locking mechanism on the machine and a door strike on the door itself. When the door lock malfunctions, it can cause various issues such as the door not locking properly or the machine not recognizing that the door is locked, which prevents the Electrolux washer or spin cycle from working. Closely examine the lock for any wear or damage. If any problems are found, the door lock needs to be replaced.

How to Replace Washing Machine Door Lock

1. Shut off power. Unplug the washing machine from the electrical outlet or turn off the power at the circuit breaker to ensure the machine won't accidentally turn on during repairs.

2. Remove outer cover. Use a Phillips head screwdriver to remove any screws securing the outer plastic or metal cover. Lift it off to access the inner components.

3. Disconnect old lock. Locate the door lock assembly, usually on the bottom left or right side of the tub opening. Unplug any electrical connections and unwind wire clips or ties holding the wires in place.

4. Unfasten lock bolts. Use your screwdriver to remove any mounting bolts, screws or clips attaching the old lock to the washing machine frame. Lift it out once it's fully detached.

5. Align new lock. Hold the replacement lock in position so the bolt holes line up with the frame. Make sure gaskets or seals are in the correct position first if applicable.

6. Reattach with bolts. Thread the mounting bolts back through the lock and tighten them to secure it firmly in place. Do not overtighten.

7. Reconnect wires. Plug any electrical connections back into the replacement lock and secure wires with ties or clips to protect them.

8. Replace cover. Slide the outer cover back into position and install the retaining screws to complete the repair. Restore power and test that the new lock is functioning properly before use.

Repair Instructions:

A shift actuator is a part found in top-load Electrolux washers that is responsible for switching the tub's rotation from agitate to spin. If the tub is not spinning at all, a broken shift actuator might be the cause. It is important to examine the shift actuator for any signs of damage and replace it if needed.

How to Replace Washing Machine Shift Actuator

1. Prepare for the replacement: Gather the necessary tools and equipment for the replacement process. You will typically need a wrench, pliers, screwdriver, and a replacement shift actuator that matches your specific washing machine model. Make sure that the washing machine is unplugged and disconnected from any power source.

2. Access the shift actuator: The shift actuator is usually located near the motor and transmission assembly of the washing machine. Depending on the model, you may need to remove the control panel or the rear access panel to access the shift actuator. Consult the manufacturer's instructions or the washing machine's manual for specific guidance.

3. Disconnect the wiring: Locate the wiring harness connected to the shift actuator. Carefully disconnect the wiring by gently pulling apart the connectors. Take note of the positions or colors of the wires for proper reconnection later.

4. Remove the old shift actuator: Use a wrench or pliers to loosen and remove any mounting screws or bolts that secure the shift actuator to the washing machine. Once the fasteners are removed, carefully detach the old shift actuator from its position.

5. Install the new shift actuator: Take the replacement shift actuator and align it with the mounting location on the washing machine. Ensure that it fits securely into place. Use the previously removed bolts or screws to fasten the new shift actuator to the machine. Tighten them appropriately but avoid over-tightening.

6. Reconnect the wiring: Reconnect the wiring harness to the corresponding connectors on the new shift actuator. Match the wire positions or colors as noted earlier to ensure correct alignment. Ensure that the connections are secure and properly seated.

7. Replace the control panel or access panel: If you removed the control panel or rear access panel to access the shift actuator, reattach it securely. Align it properly and use the appropriate screws or fasteners to secure it in place.

8. Test the washing machine: Plug the washing machine back into the power source and conduct a test run to ensure that the new shift actuator is functioning properly. Run a cycle and observe the shifting mechanism to verify that the replacement was successful. Pay attention to any unusual noises or malfunctions.

9. Clean up and dispose of old parts: Dispose of the old shift actuator and any other replaced parts responsibly. If the old parts are recyclable, consider taking them to a recycling center. Clean up your work area and store your tools properly.

Repair Instructions:

The Electrolux washer hub is the part that connects the basket to the shaft responsible for spinning it. Over time, the hub can experience wear and tear, leading to problems with the Electrolux washer's spinning function. If the hub is worn or cracked, replacing it can solve the issue and restore proper spinning functionality to the Electrolux washer.

How to Replace Washing Machine Hub

1. Unplug the washing machine. Disconnect power to avoid electric shock.

2. Access the hub. Tip the Electrolux washer back or remove the front panel to access the hub.

3. Remove hub nut. Use a socket wrench to loosen and remove the hub retaining nut.

4. Remove agitator. Lift the agitator straight up to detach it from the hub spline.

5. Remove hub. Carefully pull the hub straight out from the agitator shaft.

6. Install new hub. Align the new hub onto the agitator shaft and push it straight down into place.

7. Replace agitator. Line up the agitator over the hub and push down firmly to reattach.

8. Tighten hub nut. Thread the hub retaining nut back onto the agitator shaft. Tighten securely with a socket wrench.

9. Test rotation. Rotate the agitator manually to ensure the hub engages the agitator properly.

10. Restore Electrolux washer position. Carefully tip the Electrolux washer back upright or replace the front panel.

11. Restore power. Plug in the washing machine and test operation.

12. Run test cycle. Verify smooth agitation before washing clothes. Tighten hub if needed.

Repair Instructions:

The clutch assembly is responsible for linking the transmission and the inner tub. It helps the tub to gradually reach the correct spin speed. However, if the clutch is worn out, it can hinder the tub from spinning. Unfortunately, the clutch cannot be repaired. If you find that the clutch is worn out, it should be replaced.

How to Replace Washing Machine Clutch

1. Unplug the washing machine. Disconnect power to avoid electric shock.

2. Access the clutch. Remove the back service panel to access the clutch assembly.

3. Drain water lines. Empty any water lines attached to the clutch using a pan.

4. Disconnect clutch actuator. Detach the actuator rod, spring or motor from the clutch, if applicable.

5. Loosen mounting bolts. Use a socket wrench to loosen the mounting bolts on the clutch assembly.

6. Remove clutch. Carefully work the clutch off the drive shaft once bolts are detached.

7. Install new clutch. Slide the new clutch onto the drive shaft and align it into place.

8. Tighten mounting bolts. Secure the clutch by tightening the mounting bolts with a socket wrench.

9. Reconnect actuator. Reattach the actuator rod, spring or motor to the new clutch.

10. Replace service panel. Reattach the back service panel once done.

11. Restore power. Plug washing machine back in and test operation.

12. Check engagement. Verify the clutch engages properly when cycled on and off.

Repair Instructions:

The clutch band kit is responsible for linking the transmission and the inner tub in the Electrolux washer. Its role is to help the tub reach the correct spin speed gradually. When the clutch becomes worn out, it can hinder the tub from spinning properly. If you find that the clutch band kit is worn out, it should be replaced.

How to Replace Washing Machine Clutch Band Kit

1. Unplug the washing machine. Disconnect power to avoid electric shock.

2. Access the clutch. Remove the back service panel to locate the clutch assembly.

3. Remove old bands. Carefully detach the old clutch bands from the pulleys and clips.

4. Clean pulleys. Use a wire brush to clean the drive and brake pulleys.

5. Install new bands. Loop the new clutch bands around the pulleys as directed.

6. Secure bands. Attach the guide clips and spring hooks to hold the bands in place.

7. Check alignment. Make sure the bands are properly aligned and taut.

8. Adjust band tension. Turn the tensioning springs to achieve the right tension on each band.

9. Replace service panel. Reattach the back service panel once done.

10. Restore power. Plug washing machine back in.

11. Test operation. Run Electrolux washer through cycles to verify proper clutch engagement and braking.

12. Repeat tensioning. Recheck band tension and adjust springs again if needed.

Repair Instructions:

The door latch is responsible for securely closing the Electrolux washer door during operation. Once the door is properly shut, the Electrolux washer can start working. However, if the Electrolux washer door is not latched shut, the door switch will prevent the Electrolux washer from operating. If there's a problem with the door latch, the Electrolux washer will not spin or start. The door latch can fail either mechanically or electrically. Check the door latch for any signs of damage. If the latch is damaged or doesn't close correctly, it should be replaced. To check if the door latch has an electrical issue, you can use a multimeter to test the switches on the latch for continuity. If any of the switches lack continuity when activated, it's necessary to replace the switch.

How to Replace Washing Machine Door Latch

1. Unplug the washing machine. Disconnect power to avoid electric shock.

2. Open the door. Prop the door fully open to access the latch assembly.

3. Remove inner door panel. Detach the screws or clips to remove the inner door panel, if needed for access.

4. Detach latch linkage. Disconnect the latch assembly linkage rods from the door mechanism.

5. Remove mounting screws. Use a screwdriver to detach any screws securing the latch to the door frame.

6. Remove old latch. Carefully detach and remove the old, malfunctioning latch mechanism.

7. Install new latch. Align and insert the new latch assembly into the door frame opening.

8. Reattach mounting screws. Tighten screws to securely fasten the latch assembly in place.

9. Reconnect latch linkages. Attach the latch linkage rods back to the door mechanism.

10. Replace inner door panel. If removed, reattach the inner door panel.

11. Test operation. Close the door and test the latch engagement before regular use.

12. Restore power. Plug washing machine back in once the new latch is installed and working.

Repair Instructions:

The motor control board is responsible for supplying power to the motor. If the motor control board is faulty, it can cause the Electrolux washer to not function properly or not work at all. Start by inspecting the control board for any burned-out components. To check if the motor control board is defective, make sure it is actually providing power to the motor. If the control board has power but fails to supply power to the motor, it should be replaced.

How to Replace Washing Machine Motor Control Board

1. Unplug the washing machine. Disconnect power to avoid electric shock.

2. Access the control board. Remove the back service panel to locate the motor control board.

3. Label wire connections. Take note of where all the wiring harnesses connect to the control board.

4. Disconnect wires. Detach all the wire harnesses by hand or using pliers.

5. Remove mounting screws. Use a screwdriver to remove any screws securing the control board.

6. Remove old control board. Carefully detach the old motor control board from the washing machine.

7. Install new control board. Align the new motor control board and reinsert the mounting screws.

8. Reconnect wiring. Attach all the wiring harnesses to the correct terminals on the new control board.

9. Replace service panel. Reattach the back service panel once done.

10. Restore power. Plug in the washing machine.

11. Test operation. Run a test cycle and check that the motor functions properly before regular use.

12. Troubleshoot issues. If the motor still does not operate right, double check the wiring connections.

Repair Instructions:

Make sure that the lid or door is fully closed. Check for anything that might be blocking it and remove it. Make sure the door strike on the door or lid is not damaged or broken. If you find that the door strike is indeed broken, it will need to be replaced.

Repair Instructions:

Make sure that water is flowing into the tub from the water supply. If the water supply is slow or not entering the tub at all, the Electrolux washer will pause before reaching the spin cycle as it waits for the tub to fill. There are a few possible causes for this issue, such as a clogged water inlet valve, the main water supply valve being partially closed, or low water supply pressure from the home.