Electrolux Washer Valve

The Water Dispenser Valve is an OEM part for Frigidaire washing machines. This valve controls the flow of water into the washing machine during the wash and rinse cycles. It ensures that the correct amount of water enters the drum, contributing to efficient and effective cleaning.

Causes of a bad water dispenser valve can include mineral deposits or debris clogging the valve, wear and tear over time, or electrical faults that affect the valve’s operation. 

Symptoms of a bad water dispenser valve include:

• No water entering the washer
• Insufficient water during cycles
• Leaks around the valve area
• Inconsistent water flow

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Water Valve is an OEM part for Frigidaire washing machines. This part controls the entry of water into the washer during the wash and rinse cycles. 

Common causes of a bad valve include mineral deposits from hard water, electrical issues, or general wear and tear over time.

Symptoms of a bad washer water valve include:

• Washer not filling with water
• Slow water fill rate
• Leaking water from the valve area
• Inconsistent water temperature

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Water Inlet Valve is an OEM part for Frigidaire washing machines. This part controls the flow of hot and cold water into the washer's tub, ensuring the correct temperature mix for various wash cycles. By opening and closing at the command of the washer's control system, it plays a pivotal role in the machine's ability to execute programmed wash cycles with precision, affecting everything from the initial fill to the rinse phases. 

Causes for the replacement of the water inlet valve can range from mineral deposits and sediment build-up, which can obstruct the valve's flow, to mechanical wear and electrical failures affecting the valve's operation. 

Symptoms of a malfunctioning Water Inlet Valve include:

• The washer not filling with water 
• Water entering the machine slowly 
• The washer filling with the wrong water temperature

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Water Inlet Valve Assembly is an OEM part for Frigidaire washing machines. This assembly controls the flow of water into the washing machine during the fill cycles, ensuring the correct amount of water enters the tub.

Over time, the water inlet valve can become faulty due to mineral buildup, wear and tear from frequent use, or damage to the valve components. If the valve is not functioning properly, it can result in issues with the water flow into your washing machine.

Symptoms of a bad water inlet valve assembly include:

• No water entering the washing machine
• The washer filling slowly or not at all
• The washing machine filling with water when it is turned off
• Leaks from the valve area

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Water Inlet Valve is an OEM component for Frigidaire washing machines. It resides within the base and precisely controls water intake into the washer tub. 

Symptoms of a bad water inlet valve include:

• Failure to fill the tub with water for cycles  
• Residual water leaks at the valve area
• Inability to select fill levels on newer machines
• Restricted or no water flow into hoses

Causes may be mineral sediment buildup inhibiting valve function over time, worn internals allowing leaks, or electronic issues in smart valves.

Compatible with units including Electrolux, Gibson, and select Kenmore models as well. Renewed laundry performance awaits with this vital component repair.
 

The Water Valve is an OEM part for Frigidaire dryers featuring a steam cycle option. This valve controls the flow of water into the dryer drum during steam cycles.

Causes for replacement typically relate to standard wear and tear issues compromising the valve's ability to regulate water precisely during steam cycles. Mineral buildup from hard water sources can also obstruct full valve movement.

Symptoms of a faulty steam dryer water valve include:

• Inability to select steam cycle options
• Error codes related to steam or water systems
• Inconsistent steam levels during cycles

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This triple-solenoid washer water inlet valve regulates and routes hot and cold water into the tub and dispenser as the control commands. Replacing a weak, stuck, or leaking valve restores proper fill, temperature mix, and cycle performance. What it does:

• Opens and closes to allow water into the washer based on cycle and temperature selections
• Three solenoids manage hot/cold mix and direct water to the tub and dispenser compartments
• Typical symptoms: won't fill, slow fill, fills when powered off, incorrect temperature, or leaks from the valve
• May trigger fill-related error codes or cause extended/paused cycles due to fill timeout

• One water inlet valve assembly with three solenoids

• Disconnect power and turn off both hot and cold water supplies before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Label and transfer each wire connector and hose to the matching port on the new valve
• After installation, open supply valves and run a test fill; inspect all connections for leaks

This water inlet valve controls the flow of household water into your appliance during operation. Replacing a sticking or leaking valve restores proper filling and helps prevent unwanted water entering the unit between cycles.

• Opens and closes to regulate water flow when energized by the control
• Failure can cause no fill or very slow fill during cycles
• Can contribute to leaks at the back or water-inlet/fill error alerts

• Disconnect power and shut off the water supply before servicing
• Keep a towel or pan handy to catch residual water; relieve hose pressure
• Note/label hose and wire locations; transfer any brackets or screws from the original valve as needed
• Restore water and power, tighten connections, and check carefully for leaks with a test fill

This dispenser valve assembly controls water flow to the fridge door dispenser for reliable dispensing and shutoff. It replaces a failed valve to restore proper water delivery and stop unwanted dripping or leaks. What it does

• Opens and closes the water passage when the dispenser actuator is pressed to deliver water to the glass.
• Seals the water line to prevent drips or continuous flow when the dispenser is idle.
• Helps stop intermittent dispensing or no-water issues caused by a faulty valve.
• Works with the door dispenser plumbing—electrical/connectors remain unchanged.

• Disconnect power and shut off the refrigerator water supply before starting.
• Remove the refrigerator door panel or access cover per your model's service instructions to reach the valve.
• Verify electrical connector seating and water line fittings are secure; replace any damaged tubing or seals.
• Test for leaks and proper dispensing after restoring power and water.

Restore proper flow control with this replacement valve assembly. It opens and closes as commanded by the appliance's controls to route fluid to the correct circuit, helping resolve no-flow, slow flow, and leak issues.

• Regulates on/off flow to the designated system/component when signaled
• Directs fluid to the intended circuit for proper fill/dispense operation
• Common symptoms of a failing valve include no flow, slow/intermittent supply, won't shut off, or leaks at the valve or fittings
• May produce humming or clicking without actual flow when malfunctioning

• Disconnect power and shut off the supply line before servicing
• Relieve line pressure and place a towel or tray to catch residual fluid
• Note hose/connector positions; transfer any brackets or fittings from the original if required
• Restore supply and check all connections for leaks and proper operation