Electrolux Washer Control Board

This is a motor control board for a washing machine. It comes with the board, tape, bracket, and screw mounted on control. In most cases, this part is located on the bottom of the appliance near the drive motor. The purpose is to control the speed of the drive motor. It also works to determine the direction of the tumble and spin actions while a cycle is in process. If the washing machine is pumping but does not spin, this is often the result of a malfunctioning motor control board.If the motor control board has gone bad, it should be replaced. To replace it, make sure the washer is unplugged or the circuit breaker has been turned off. Pull the washer away from the wall, remove the knobs from the front and screws from the back, and lift the control panel. This offers access to the motor control board, which should be removed so the new part can be installed.This motor control board is made for use with washing machines by Electrolux, Frigidaire, Crosley, and Kenmore. It is sold on an individual basis. This is an authentic OEM replacement part that is directly sourced from the manufacturer.

This pre-programmed user interface control board assembly manages the buttons and display on your appliance's control panel. Replacing a failed UI board restores responsive controls and accurate indications from the panel. What it does:

• Interprets keypad inputs and drives the display/indicator LEDs
• Sends user selections to the main control for proper operation
• Helps resolve an unresponsive or intermittent control panel
• Addresses blank, flickering, or garbled display behavior

• 1 pre-programmed user interface control board assembly

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD protection; handle the PCB by the edges only
• Photograph wiring and ribbon connections; match keyed connectors and orientation on reassembly
• Reuse existing mounting hardware, trim, and overlays as needed; ensure all harnesses are seated before restoring power

This UI board assembly replaces the refrigerator's user interface/control board to restore button response and display feedback. It lets you reliably set temperatures and modes so the appliance accepts and shows commands correctly. What it does:

• Receives and processes user inputs from the control panel (buttons/touchpad) so selections register and run.
• Drives the front display and indicator lights so temperature, mode and status information is visible.
• Replaces a failed or intermittent interface that causes unresponsive controls, blank or garbled display, or incorrect status indications.
• Works with the main control to pass commands; replacing the board can isolate interface-specific failures.

• Disconnect power to the appliance before starting — this part is electronic and may be damaged by live power.
• Take photos of existing wiring and mounting before removal to ensure correct reassembly.
• Handle the board by its edges and avoid static discharge; use anti-static precautions if available.
• Reconnect all plugs securely and test functions before fully reinstalling trim or covers.

This electronic control board manages the appliance's cycle logic and power to key components. Replacing a failed board can restore proper operation when the unit is unresponsive, won't start or advance, or shows recurring error codes. What it does:

• Governs cycle timing and overall machine logic
• Interprets inputs from sensors and the user interface
• Sends power to major loads such as the drive motor, pump or heater, and related components
• Common failure symptoms include no start, stalled cycles, unresponsive controls, or repeated error codes

• 1 electronic control board

• Disconnect power before servicing; handle the board with ESD protection
• Photograph wiring and transfer connectors and any jumpers/settings from the original board
• Inspect harnesses and connected loads for shorts to prevent repeat failure
• After installation, run the model's diagnostic or calibration procedure if applicable

This electronic control board replaces a failed or intermittent refrigerator control to restore reliable electronic management of the appliance. It's the main circuit board that coordinates temperature, defrost and other timed functions. What it does:

• Manages electronic signals for temperature regulation and compressor/fan control
• Controls timed operations such as defrost cycles and automatic functions
• Interfaces with user inputs and display/LED indicators
• Helps stop erratic behavior caused by a damaged or shorted control board

• One electronic control board

• Disconnect power to the appliance before starting any work
• Access may require removing an interior or rear access panel; keep screws and fasteners organized
• Avoid static discharge; handle the board by its edges and avoid touching components

This electronic main control board manages a fridge's user inputs and core functions so the appliance responds correctly to commands and cycles. Replacing a faulty control board restores reliable control and display operation. What it does:

• Receives signals from the user interface and sends commands to compressors, fans and other subsystems
• Manages timing and basic operational logic for cooling and accessory functions
• Restores display and front-panel responsiveness when the board is the failure point
• Stops or prevents erratic or intermittent appliance behavior caused by a failed control module

• One control board

• Disconnect power to the appliance before beginning work
• Handle the board by the edges and avoid static discharge; use a grounding strap if available
• Document connector locations/arrow orientations before unplugging; reconnect all harnesses firmly

This electronic control is the main user interface and timing brain for your oven or range, restoring reliable cycle selection and display functions so cooking settings respond correctly. What it does:

• Replaces a faulty control board that governs bake/ broil/clock and timer functions
• Restores button/keypad and digital display responsiveness when commands aren't registering
• Helps resolve intermittent operation, incorrect cycle starts, or unresponsive controls
• Works with existing wiring harness and sensors when those components are good

• One electronic control board

• Disconnect power to the appliance at the breaker before beginning any work
• Handle the board by its edges and avoid contact with circuit traces or components
• Verify other components (wiring harness, door switch, sensors) before replacing the control

This user interface control board replaces the oven's front control module so you can send commands and view settings. It restores responsive touch/buttons and proper display feedback for normal operation. What it does

• Receives button/touch inputs and relays commands to the oven control system
• Provides display/status feedback so settings and timers are visible
• Helps resolve unresponsive buttons, blank or incorrect display readouts, or intermittent control behavior
• Works as the main input surface for oven functions like bake, broil, timers, and temperature settings

• One user interface control board (UI board) — only items explicitly listed by the manufacturer are included

• Turn power to the appliance off at the breaker before servicing to avoid electrical shock
• Handle the board and connectors carefully; avoid touching contacts or flexing the board
• Verify connector orientation and secure mounting; test operation with power restored

This electronic control board governs the refrigerator's functions and user interface, restoring reliable temperature control and cycle management when the original board fails. Replaces a faulty or unresponsive control module to return normal operation. What it does:

• Manages compressor, fans and defrost cycles by sending timed signals to key components
• Controls temperature setpoints and responds to user interface inputs
• Can cause unresponsive displays, incorrect temperatures, or failure to start if faulty
• Helps clear intermittent operation or erratic cycling linked to a bad control board

• One electronic control board (main)

• Disconnect power to the appliance before starting; verify power is off at the breaker
• Handle the board carefully; avoid static discharge and do not touch circuitry
• Note connector positions and mounting locations for correct reassembly

This UI board assembly is the user interface electronics that lets you command and monitor your range/oven. It restores touchpad buttons and display feedback so the appliance responds to temperature and timer settings. What it does:

• Receives and processes user inputs from touchpads or buttons
• Controls and displays oven settings, timers, and status information
• Passes commands to the main control/relay board for heating and functions
• Commonly replaced when buttons or display are unresponsive or incorrect

• One UI board assembly

• Disconnect power at the breaker before starting; risk of shock if powered
• Handle the board by the edges and avoid static discharge; wear an ESD strap if available
• You may need to remove the control panel or console to access the board; keep track of screws and connectors