Electrolux Washer Hose Or Tube

The Tub to Pump Hose is an OEM replacement part for Frigidaire washing machines. This hose connects the tub to the pump, allowing water to be drained out of the tub and into the drainage system. 

Causes for a malfunctioning Tub to Pump Hose can include blockages from lint or small objects, cracks or holes in the hose material, or loosening of the hose clamps that secure it in place.

Symptoms of a bad Tub to Pump Hose include:

• Water leaking from the bottom of the machine
• Slow or incomplete drainage
• Unusual noises during the drain cycle
• Error messages related to water drainage

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This washer tub-to-pump hose connects the outer tub to the drain pump, carrying wash water out during the drain cycle. Replacing a cracked, clogged, or leaking hose helps stop leaks, restore dependable draining, and prevent water damage.

• Directs water from the outer tub to the drain pump during drain and spin
• Common symptoms: water leaking under the washer, water left in the drum, slow or no drain, or drain-related error codes
• Wear, heat, or debris/foreign objects can cause splits, soft spots, or blockages
• Restores a sealed flow path to improve drainage and reduce leaks

• Unplug the washer and turn off water supply; use gloves and have towels or a shallow pan ready for residual water
• Access the pump area through the lower front or rear service panel (varies by model)
• Note routing/orientation; move clamps back, seat the new hose fully on both fittings, and resecure clamps
• Run a short rinse/drain cycle and inspect all connections for leaks

The Drain Hose is an OEM part for Frigidaire washing machines. This hose is essential for directing used water out of the washing machine and into the household drain system, ensuring efficient water removal after each wash cycle.

You should replace the drain hose if it becomes damaged or clogged. Causes of a bad drain hose include wear and tear from repeated use, blockages from debris or lint, or physical damage such as cracks or splits. A compromised drain hose can lead to water leakage, improper drainage, or even flooding.

Symptoms of a bad Drain Hose include:

• Water not draining properly from the washing machine
• Leaks or puddles of water around the washing machine
• Visible cracks or splits in the hose
• Unusual sounds during the draining process

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Tub to Pump Hose is an OEM part for Frigidaire washing machines. This part directs water from the tub to the pump during the wash cycle. This flexible hose plays a role in the machine's ability to drain water efficiently after each wash or rinse cycle, ensuring optimal performance. 

Causes for replacement might include wear and tear over time that leads to cracks or holes in the hose, blockages that prevent water from draining properly, or improper installation that results in leaks or water retention. 

Symptoms of a bad Tub to Pump Hose include:

• Leaks found underneath the washing machine
• Problems with the washing machine draining properly
• Puddles of water appearing during or after a wash cycle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dispenser to Tub Hose is an OEM part for Frigidaire washing machines. This hose is responsible for transporting detergent and other cleaning agents from the dispenser to the tub during the wash cycle.  

Common causes of a bad hose include constant exposure to water and detergent, which can lead to wear and tear, blockages from detergent buildup, or physical damage such as cracks and splits.

Symptoms of a bad dispenser to tub hose include:

• Water leaks near the detergent dispenser
• Uneven or insufficient distribution of detergent
• Visible cracks, splits, or other damage to the hose
• Error codes on the washing machine related to water flow

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Sump Hose is an OEM part for Frigidaire washing machines. This hose carries water from the tub to the pump, ensuring proper drainage during the wash and spin cycles.  

Causes of a bad sump hose can include regular wear and tear, cracks or holes from aging, and clogs from debris buildup. 

Symptoms of a bad sump hose include:

• Water leaking from the bottom of the washing machine
• Slow or incomplete drainage
• Visible cracks or holes in the hose
• The washing machine stopping mid-cycle due to drainage issues

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This tub-to-pump hose connects the washer's outer tub to the drain pump, channeling water out during the drain cycle. Replacing a worn hose helps stop leaks and restore consistent draining when the original is cracked or deteriorated.

• Provides a sealed path from the outer tub to the drain pump during draining
• Helps the washer remove water at the end of wash and rinse cycles
• Common failure symptoms: water leaking at the front/bottom, puddles after a cycle, or slow/no drain
• Visual clues: cracks, splits, swelling, or soft spots in the hose rubber

• Unplug the washer and turn off water supply; expect residual water—use a pan/towels
• Access the hose per your model (often behind the lower front/service panel); note routing/orientation before removal
• Transfer and reuse the existing clamps; seat the hose fully on both fittings and secure evenly
• After reassembly, run a brief fill/drain test while watching for leaks

This drain hose carries wastewater from the washer's drain pump to your home standpipe or sink, ensuring proper draining and helping prevent leaks or backflow. Replace a cracked, kinked, or clogged hose to restore reliable draining.

• Provides a sealed path for wastewater from the drain pump to the household drain
• A damaged or clogged hose can cause leaks, slow draining, or drain-related error codes
• Kinks, splits, or pinholes may allow water to escape during drain cycles
• Loose or worn hose ends can lead to drips at the pump or rear connection

• Disconnect power and water supply; pull the appliance forward to access the hose
• Expect residual water—use towels or a shallow pan and clamp off the old hose if needed
• Note hose routing and clamp locations; reuse existing clamps and secure connections firmly
• Route the new hose without kinks and set the discharge height per your installation guide to prevent siphoning

This replacement hose routes water within your washer. Replacing a cracked, worn, or leaking hose restores a secure, watertight path so the machine can move water properly without puddles or performance issues.

• Transfers water between internal components during wash cycles
• Maintains a sealed flow path to help prevent leaks
• Damage may present as water on the floor, moisture under the unit, or related fill/drain errors
• Cracks, swelling, abrasion, or loose connections are common failure signs

• Unplug the washer and turn off water supply; have towels or a pan ready for residual water
• Note hose routing and clamp positions before removal; photos can help
• Transfer or replace clamps as needed; seat connections fully and secure firmly
• Run a test cycle and check all connections for leaks

A replacement flexible hose that routes water between appliance components to restore proper flow and help prevent leaks. Use this hose when a worn or damaged line is causing pooling or reduced water movement. What it does:

• Carries water between internal components
• Replaces cracked, split, or clogged tubing that can cause leaks
• Helps stop water pooling under or around the appliance
• Can resolve weak or intermittent water flow caused by damaged tubing

• Disconnect power and shut off the water supply before you start
• Inspect routing to avoid kinks; secure with proper clamps or brackets
• Tighten connections evenly and check for leaks after restoring power/water

Tub to pressure switch hose.

This air chamber directs refrigerated air from the freezer to the fresh food section to help maintain consistent temperatures and proper airflow. It replaces a cracked or damaged diffuser that can disrupt cooling performance. What it does:

• Channels cold air through the refrigerator compartments for balanced cooling
• Helps prevent temperature imbalance and warm spots in the fresh food area
• Reduces uneven frosting or condensation caused by airflow leaks
• Restores intended airflow path when the original chamber is broken or missing

• Disconnect power to the appliance before starting any repair
• Typically installs behind interior liners; remove shelves and panels as needed for access
• Handle the part and surrounding trim carefully to avoid damaging clips or seals

This replacement 5-foot fill hose with elbow delivers water from the household supply to the appliance, restoring proper fill flow and helping stop leaks from worn or damaged inlet lines. Designed as a direct-replacement assembly for compatible refrigerators. What it does:

• Carries water from the supply valve to the appliance's inlet connection.
• Elbow fitting provides a low-profile connection to reduce kinking at tight inlets.
• Replaces cracked, split, or leaking hoses that can cause slow/no fill or visible leaks.
• Restores reliable water delivery for ice makers and dispensers when the original hose is failing.

• Two 5' fill hoses with elbow fittings (quantity: 2).

• Shut off the water supply and unplug the appliance before starting any work.
• Inspect fittings and replace any damaged clamps; hand-start fittings, then tighten with an appropriate wrench—do not overtighten.
• Check for leaks after turning the water back on and run a fill cycle to verify proper operation.