Roper Cooktop Heating Element

• Little to no heat when broiling
• Element will not heat

Turned off breaker to oven, took pictures of existing broil, supporting bracket and shield attached to oven, removed screws holding element, support piece and shield, removed bracket and shield, pulled out the element, took another close-up picture of the wires connected to element, removed wires, connected new element, turned breaker on to see if connection is correct, turned it off, installed element, shield and support bracket (in this order). Turned breaker on. Hardest part was loosening... Read more

• Little to no heat when broiling

Cut off power ,inside I remove the two back screws, remove the two front screws with hangers. Pull element out, clip wires so they don't fall back in holes with clothes pins. worked good. But wire connection to the broiler was to large, had to replace connectors, wire fell in hole, had to pull wall oven out and remove back panel. I then mounted the new element to oven. Replaced connectors ,connected connectors, closed back panel, put oven in place ,connected power lines. Turned power on. Works... Read more

Ordered new heating coils for stove Read more

• Little to no heat when baking

It took 10 minutes and a screwdriver, remember to turn off power to the oven at the fuse box. By the way, I ordered the part at 1:30pm and received it at 12:30pm the next day using normal shipping, not bad. Read more

• Little to no heat when broiling
• Element will not heat

Replaced element Read more

• Element will not heat

Not really a repair, just needed to update some parts that were worn out. Drip pans were perfect and I am so glad to have found them on this location. Read more

Open oven door removed 2 screws to lift up top then remove 1 screw at back of burner assy to let right side burner assy drop down to replace then remove wires be sure to write down where wires go look on bottom side for location of wire plugs new burner plugs may be located in different location mine was then install new burner assy Read more

Bought replacement burner receptacles. Cut off the old ones, used wire nuts to connect replacements. Read more

Very simple to fix this problem and took only a few minutes. Appliance Parts Pros has the best delivery service. I ordered the part about 2pm and the part was delivered at 11am the next morning. I live in the Atlanta area so delivery is probably faster than other areas but they always ship the same day if the order is placed before 5pm. I have used App Parts Pros several times over the last 5 years and have always been very satisfied with the service and the parts. Read more

• Element will not heat

The burners and drip pans that I previously ordered fit this stove perfectly. It is so much better cooking on the cook stove with the burners laying properly. I'm very pleased. My only complaint is that I wish more parts were available for this old stove, I really love it! Read more

Changed element. Read more

• Element will not heat

We ordered the part it arrived within a couple of days and my son installed it without any trouble. Read more

Ordered a new one from appliance pro got it fast and put it in work's great. Read more

REPLACED NEW RIGHT FRONT POWER BURNER. THIS DID NOT FIX THE PROBLEM. I THEN REPLACED THE BURNER CONNECTING SWITCH BY FOLLOWING THE INSTRUCTIONS ON YOUR VIDEO. BURNER HEATS UP NORMALLY, BUT I DON'T KNOW YET IF IT WILL SUDDENLY GO TO THE HIGH SETTING. IT WAS A SPORADIC PROBLEM I WAS HAVING...SO I'M HOPING THIS SOLVES THE ISSUE. FINGERS ARE CROSSED....BUT IN EITHER CASE....I NEEDED A NEW BURNER. REPAIR WAS SIMPLE....THE INSTRUCTIONAL VIDEO WAS VERY EASY TO FOLLOW. Read more

• Little to no heat when baking

Having a very old wall oven,I could not find any parts or manual associated. Chris diligently located a part that would hopefully replace the old element. The old oven did not have the sleeve type connector used for the current elements. The old wiring had a screw attachment. I drilled a small hole at end of new element connector and then screwed the wire and element together like the original. Not difficult but very pleased and it worked fine. Thanks to Chris and ApplianceParts Pros for... Read more