Roper Range Parts

Watched video from AppliancePartsPros.com, ordered part. I followed instructions on video and oven door works great now!!! Read more

Using the parts I ordered, I replaced the glass myself following the very helpful video on your web site. Read more

Kit arrived promptly. it took help of a friend and 45 minutes to install Read more

Replaced the hinge receiver with a new one. The old one was bent slightly inside where it could not be seen. I think someone pushed the door down to far or fell on it. 2 screws to remove it, take out storage drawer and reach up little ways to remove and replace the receiver. Replace the 2 screws. The receiver comes with 2 screws but I ordered an extra ( never used it ). The sides of the receiver were spread just a tiny bit but were enough to cause a problem. Read more

Bought a Thermador PRSE48" dual fuel range from Craigslist really cheap because it didn't work. Did a little research and decided to overhaul most of the top (gas) end. For what I paid for it it was worth it and I'd have a good stove with new components. Replaced the griddle thermostat, ignition micro switches, ignition re-igniter box, installed fixing kit with 2 new potentiometers, both solenoids, and gas regulator. Had to replace 2 gas lines, all 4 jets, and one brass nut that were... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light

Called a repairman and he told us we needed to change a bunch of parts and would cost over $400! Decided to do some research online and found suggestions to replace the spark igniter. Decided to give it a try. Took about 10min to replace and oven is now working perfectly, for a total of $30! Read more

Installed it according to video watched. Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

The problem is a finicky ignition system, Direct Spark Ignition. Apparently Whirlpool redesigned the igniter/burner assembly slightly to make it more reliable. The repair is very easy. Turn off power, but you don't need to turn off gas. Remove oven bottom and flame spreader, then remove burner/igniter assembly, one screw at front, one at back. Lift out burner assembly carefully to avoid stretching wire. Pull electric connector from pin on burner/igniter assembly. Vacuum to clean oven. ... Read more

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

I first DISCONNECTED POWER FROM THE RANGE using the breaker. I then pulled the range out from the wall to give myself plenty of working room. I lifted the range top up as when you clean under the burners. I then moved the ends of the bottom of the slide rods that lock the range top open back where they came loose from the top of the range. This allows you to fold it higher and have complete access to the top of the range. I then took out all the Phillips head screws that hold down the sheet... Read more

Quick replacement by sliding out the old filters and sliding in the new filters. Read more

, shut gas valve to range, unplug from wall outlet, ordered thermostat. less then 30 minutes to install new thermostat, range back to normal function Read more

• Little to no heat when broiling
• Element will not heat

Turned off breaker to oven, took pictures of existing broil, supporting bracket and shield attached to oven, removed screws holding element, support piece and shield, removed bracket and shield, pulled out the element, took another close-up picture of the wires connected to element, removed wires, connected new element, turned breaker on to see if connection is correct, turned it off, installed element, shield and support bracket (in this order). Turned breaker on. Hardest part was loosening... Read more

First and foremost I UNPLUGGED THE OVEN!. I'll pass on the early morning SHOCK THERAPY! Second, I unscrewed aluminum protection plate from back of oven. Next, I unplugged the two connections behind the oven switch. Then I removed the plastic switch from the front and unscrewed the two screws that secured the oven switch to the oven. Once you've completed all these steps you take your new oven switch and do everything again but in reverse order. Hope this was informative, direct, and that your... Read more