Roper Range Parts

This range control switch regulates power to a surface heating element, letting you adjust the burner from low to high for precise cooking. A worn or failed switch can cause erratic heat or a burner that won't respond to settings.

• Varies power to the surface element for steady, selectable heat
• Common failure symptoms: burner won't heat, stuck on high, won't turn off, or only one temperature
• Restores proper control of the affected surface burner

• Disconnect power before servicing; this is a live-voltage component
• Match and transfer wires terminal-for-terminal from the old switch
• Handle the control shaft carefully to avoid damage
• Test the burner at multiple settings after installation

This hinge receiver mounts to the appliance frame and accepts the door hinge arm/pin. It keeps the door aligned and secure so it opens and closes smoothly. Replacing a worn or cracked receiver restores proper door action.

• Anchors the hinge arm/pin at the cabinet/frame for smooth door movement
• Maintains door alignment and consistent closing action
• Wear or damage can cause a loose or sagging door, misalignment, or binding
• Common signs include clicking/grinding noises and visible cracks or deformation

• Disconnect power; allow the appliance to cool and shut off gas/water if applicable
• Support or remove the door to access the receiver
• Remove mounting fasteners, swap in the new receiver, and align per service instructions
• Reinstall the door and verify smooth movement and full closure

This burner box is the under-top housing for an electric cooktop or range. It supports the surface heating elements and mounting hardware, restoring proper element alignment, stability, and safe operation when the original housing is bent, corroded, or damaged.

• Supports and positions the surface heating elements beneath the cooktop
• Provides mounting points for element brackets and component supports
• Helps keep elements level and secure for consistent heating performance
• Common symptoms: loose or sagging elements, rattling/vibration from the cooktop area, visible warping or corrosion, difficulty fastening element hardware

• Disconnect power at the breaker before servicing
• Lift/remove the cooktop to access the burner box; sheet-metal edges can be sharp—wear cut-resistant gloves
• Transfer elements, brackets, and wiring to the new box in their original locations; take photos for reference
• Ensure wiring is routed clear of hot surfaces and all fasteners are secure before reassembly and testing

The bake element is the oven's primary lower heat source. Replacing a failed element restores proper preheating and even baking performance when the oven won't heat or struggles to maintain temperature during the bake cycle. What it does

• Provides the main heat for the bake cycle in electric ovens
• Common failure symptoms: no heat on bake, very slow preheat, or uneven baking
• Visible damage such as blistering, cracks, or burn spots on the element indicates replacement is needed
• Helps the oven reach and hold set temperature when functioning correctly

• 1 bake element

• Disconnect power at the breaker before servicing to prevent electrical shock
• Remove oven racks; access the element mounting screws from inside the oven cavity
• Carefully pull the element forward, support the wires, and transfer the connectors one at a time to avoid losing them behind the liner
• Ensure terminals are fully seated; do not overtighten mounting screws, then restore power and test bake

The Broil Element is an OEM part for GE ranges. This part provides the necessary heat for broiling, located at the top of the oven cavity and designed to deliver even and intense heat for broiling foods.

Causes of a bad broil element can include electrical issues such as short circuits, physical damage from impacts or heavy usage, or wear and tear over time.  

Symptoms of a bad broil element include:

• The broil element not heating up
• Uneven or insufficient broiling results
• Visible damage such as blisters or breaks in the element
• The oven not reaching the desired broiling temperature

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Oven Bake Burner with Spark Igniter is an OEM part for Whirlpool ovens. This component is essential for igniting the gas in the oven, allowing it to produce the necessary heat for baking.

Please note: The igniter is only available with this kit and not separately.

You should replace the oven bake burner with spark igniter if it becomes defective. Causes of a bad bake burner or igniter can include wear and tear from regular use, exposure to high temperatures, or damage from food spills and debris. Electrical issues or a malfunctioning igniter can also lead to failure.

Symptoms of a bad oven bake burner with spark igniter include:

• The oven not heating up or taking a long time to reach the desired temperature
• Uneven baking or inconsistent cooking results
• The igniter not sparking or clicking
• Gas smell without ignition indicating the igniter is not working properly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This oven light lens gasket seals the lens to the oven liner, helping keep heat, steam, and grease out of the light housing. It maintains a secure fit for the lens and protects the bulb and wiring.

• Creates a heat-resistant seal between the light lens and oven cavity
• Helps block heat, steam, and grease from entering the light assembly
• Stabilizes the lens/retainer so the lens sits flush and secure
• Common signs of failure: torn/brittle gasket, lens feels loose, condensation or grease inside the lens, or scorching around the light opening

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove the lens retainer and lens to access the gasket; note orientation before removal
• Seat the new gasket evenly around the opening, then reinstall the lens and retainer without overtightening
• The lens sits flush and the seal is even after reassembly

Restore reliable heat on your range's small burner with this 6-inch surface coil element. Replacing a worn or burned-out coil brings back consistent temperature response and dependable everyday cooking performance.

• Supplies direct electric heat to a 6-inch cooktop burner
• Replaces a coil that is warped, cracked, or has an open/burned-out section
• Common symptoms include: burner won't heat, heats unevenly, or works intermittently
• Visible damage, hot spots, or arcing at the terminals can indicate failure

• Disconnect power by unplugging the range or switching off the circuit breaker
• Lift the old coil and pull straight out from the receptacle to remove
• Inspect the element receptacle/terminal block for discoloration or pitting; replace if damaged
• Align terminals and support, insert fully, and ensure the element sits level in the drip bowl

The Knob is an OEM part for Whirlpool ranges. It is used to control the temperature of the surface elements, allowing for precise cooking adjustments on the stove.

Causes of a bad knob can include frequent use leading to wear and tear, exposure to high temperatures, or accidental impact causing cracks or breaks.

Symptoms of a bad knob include:

• Difficulty in turning the knob or setting the desired temperature
• The knob becoming loose or not staying in place
• The burner not igniting or adjusting heat levels properly
• Visible damage, such as cracks or missing pieces

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This panel forms the floor of the oven, sitting above the bake element or burner to shield it from spills and provide a smooth, stable surface. Replace a warped or damaged panel to help maintain proper heating and easier cleanup. What it does:

• Forms the oven floor above the bake element or burner
• Shields the heat source from drips and debris to help prevent scorching and odors
• Supports designed airflow and heat distribution in the cavity
• Common replacement signs: warped or dented panel, rust or chipped finish, smoke/odors from spills beneath the panel, or uneven baking results

• 1 oven bottom panel

• Disconnect power (and shut off gas supply for gas ranges) before servicing; allow the oven to cool completely
• Remove oven racks; release front fasteners or clips and lift the old panel out of the rear tabs (method varies by model)
• Seat the new panel into rear tabs, align the front edge, and secure as originally installed
• Verify the panel sits flat and clear of the bake element or burner before reassembling

The Surface Burner Ignitor is an OEM part for Whirlpool gas ranges. This part ignites the gas to create a flame on the burner, allowing for efficient cooking.

Causes of a bad ignitor can include wear and tear from regular use, electrical issues, or physical damage to the ignitor element.

Symptoms of a bad surface burner ignitor include:

• The burner not lighting or taking longer to light
• Clicking sounds without ignition
• Weak or inconsistent flame
• The smell of gas without ignition

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This door spring restores the counterbalance on a dishwasher door so it opens smoothly and doesn't drop. Replacing a worn or broken spring brings back controlled door movement and helps protect the hinges and linkages. What it does:

• Provides tension to counterbalance the dishwasher door for smooth, controlled opening and closing
• Helps prevent the door from slamming open or feeling excessively heavy
• Common failure signs include a door that drops suddenly, won't stay partially open, or makes snapping/spring noises
• Visual signs may include a stretched, broken, or missing spring

• 1 door spring

• Disconnect power; if working on a built-in dishwasher, also shut off water and support the door
• Springs are under tension—use eye protection and gloves, and release/attach carefully
• Access is typically behind the lower/toe panel; note original spring routing and hole positions before removal
• Inspect related door linkage/cords and hinge brackets; replace any worn components to maintain proper balance

The Surface Burner Igniter is an OEM part for Whirlpool ranges and cooktops. This component is crucial for igniting the gas that fuels the surface burners, ensuring that the burners light up safely and efficiently when the control knob is turned. The igniter produces a spark that lights the gas, allowing you to cook with precision and control. The surface burner igniter wire measures approximately 43" long.

Symptoms of a failing Surface Burner Igniter include:

• The burner not lighting or taking multiple attempts to light
• Weak or no spark produced when trying to ignite the burner
• A clicking sound without ignition of the burner
• Visible damage or wear to the igniter tip

Causes of a bad surface burner igniter can include regular wear and tear from frequent use, exposure to spills and food debris that can affect its function, and electrical issues such as a short circuit or a worn-out spark module.

This OEM part is also compatible with some models from Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore.

This oven door handle replaces a broken, loose, or discolored handle and restores a secure, comfortable grip. Finished in white, it refreshes the look of your appliance while making it easy to open and close the door safely. What it does:

• Provides the handhold used to open and close the oven door
• Replaces a cracked, missing, or wobbly handle
• Helps resolve difficulty gripping or pulling the door
• Restores a clean, color-matched white appearance

• 1 white oven door handle

• Disconnect power; if gas, shut off gas supply. Allow the oven to cool completely.
• Support or remove the door and place it on a protected surface for access.
• Remove inner door screws to access the handle mounts; swap the handle and tighten screws evenly.
• Reuse existing mounting hardware; wear cut-resistant gloves and avoid overtightening.

Used for the front burner.

Color: Black. For white order WPW10202216. For almond order 8522446.New mounting screws need to also be ordered WP3196164.