Need Help?
Call
Fix a refrigerator that won't cool or runs constantly. This temperature control thermostat cycles cooling based on compartment temperature. DIY fix in 15-20 min.
I determined it was the thermostat, found the model number and Appliance Pros had one they said would work. So, I ordered one and got it in 2 days. Opened the package, read the instructions and 10 minutes later my new food was going to be cool and my water would be ice. All it took was remove housing, unplug old part, plug in new part and replace housing. Read more
Refrigerator not cooling or compressor won't start? This overload protector prevents motor damage from overheating. DIY-friendly fix in under 30 minutes.
Used a muiltimeter to test all parts and ohm'ed out all parts. found out condenser fan motor seized up [open winding in motor] replaced that, and found that also caused the compressor overload and relay to fail, from over heating and over cycling, replaced both parts, powered up the refrigerator retested all electrical parts checked amp reading on all parts under load conditions,works good know, hope to get another 15 years out of this refrigator, its a maytag. over 20 years old. Read more
Refrigerator won't stop running or freezing food? A faulty thermostat prevents proper cycling. This DIY repair takes about 30 minutes with basic tools.
I simply removed the two screws securing the control box in place, disconnected the two wiring harnesses and removed the entire assembly from the refrigerator. At the work bench, I then removed the three wires and control knob from the thermostat and popped it out of the control box. I just reversed the procedure to install the new thermostat. Read more
Collects defrost water beneath your refrigerator. Replace if cracked, warped, or leaking to prevent floor damage and protect surrounding cabinetry.
Bought new drain pan and installed. Read more
Contains two, six foot long braided hoses with 90 degree ends.
I had a problem with the drain pump on my Kenmore HE3 and I replaced it using a drain pump I ordered from APP. That fixed that problem but once I started running the washer I started getting a FH error code. I looked it up and found that it was a problem with the washer not filling properly. I pulled the washer out and found that one of the fill hoses had kinked when I pushed the washer back in place. There was also some writing on the hose that read "Change hose every five years". I know I had... Read more
Ice dispenser not working or auger keeps falling off? This coupling connects the motor to the auger. Simple 15-minute DIY fix restores ice dispensing.
Required new ice bin (container) which has busted up in pieces from the stress of trying to turn while half melted ice had it jammed, something had to give. Ice auger ripped itself out of the dispenser end breaking the ice container. Got new container, disassembled per the drawing, reassembled. Read more
Touch-up paint for appliances. Covers chips, scratches, and worn areas on range tops, refrigerators, and other appliances. Includes brush applicator.
Ordered 2 infinite burner controls from Appliance Parts Pros and watched the online video on the replacement of them at the same time. When they arrived promptly, I was ready to take on the job. The fix only took about 15 minutes because I was prepared after watching the video. Read more
This kit includes shelf support studs used to hold shelves securely in place inside the refrigerator or freezer compartment. The supports mount into the interior liner and provide a stable resting point for wire or glass shelves. Replace these if the shelf supports are cracked, broken, or missing, causing shelves to sit unevenly or fall.
The shelf support was broken for 5 years(!) I had to stack stuff under it in order to hole it up. I finally got fed up and in searching discovered that I could buy the little support to fix it. I only needed one support but the package included all 4. They just slipped over the protrusion and 'poof' it was fixed! Gee what took me so long? What a relief. Read more
Replacement door gasket seals your refrigerator to maintain temperature and prevent air leaks. Replace when worn or cracked to restore efficiency.
Glass scraper tool for cleaning cooktop surfaces. Removes stuck-on food, spills, and residue from glass cooktops. Essential for maintaining appearance.
Remove unit, remove about 12 screw holding the top to the unit switch the tops reverse steps and done Read more
This ice deflector guides ice cubes from the icemaker into the ice bin to help keep ice delivery consistent and reduce cube jams or spills. It's a simple replacement that restores proper ice routing in compatible refrigerators. What it does:
Replace ice deflector. Read more
Mounts in the dispenser to secure the ice housing assembly. Keeps the chute and door aligned for smooth dispensing. Replace if cracked, broken, or worn.
Replaced the ice tray and motor mount plate. While I was there I replaced the thermostat also. New parts arrived in a day and a half. Read more
Dryer stops early on auto cycle but works on timed? The moisture sensor control board monitors dryness levels. DIY-friendly repair, 15-20 minutes.
Did some research via the internet and figured the problem was likely the moisture control board. Watched a video of the repair of a similar unit in order to locate the moisture control board. Used the chat feature with one of the Appliance Parts Pros to get a schematic of the dryer and advice about where to use the putty knife to release the springs for access to the board. Thanks to the lady I chatted with for expert advice. Once the actual task was started, the repair took 15 or 20... Read more
Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.
Like the original. Read more
Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.
Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:
Checked out the video on your site on how to disassemble the ice maker. Was really easy when you know the correct sequence. Only 3 screws and it's out of the freezer. Disassembled the ice maker on my kitchen counter and replaced the ice stripper. Reassembled and installed back in my freezer. It is as good as new Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.