Washer Float Switch Float Parts

The Switch is an OEM component specifically designed for Frigidaire washing machines. It controls various cycle options like water temperature levels, spin speeds, and additional settings like stain removal cycles.

Causes of a bad switch can include water or chemical damage leading to component failure over time, or loose wiring connections causing intermittent issues.  

Symptoms of a bad switch include: 

• Inability to select wash cycles or adjust settings  
• Unresponsive or inaccurate temperature levels
• Lights/displays not functioning as normal
• Error codes indicating switch problems

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace yours today to avoid expensive repairs down the road.
 

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

Fix erratic or unresponsive cycle selections with this laundry center rotary encoder switch. Mounts behind the cycle knob to restore accurate settings.

Dryer won't heat or overheats on low settings? A faulty temperature selector switch prevents proper heat control. Easy DIY fix in 10-15 minutes.

Washer overfilling or underfilling? The water level pressure switch senses tub pressure to control fill cycles. DIY repair in 20 minutes or less.

If your washer overfills, underfills, or won't advance cycles, the water level pressure switch may have failed. Takes about 10-15 minutes to replace.

Washer won't start or spin? A faulty lid switch prevents operation when the lid position isn't detected. Simple clip-in replacement, typically done in 10 minutes.

This replacement switch restores reliable on/off control for the specific function it serves in your appliance. A failing switch can cause that feature to stop responding or behave intermittently; replacing it brings normal operation back.

• Opens and closes the electrical circuit to the associated component when actuated
• Provides consistent, safe control of the feature it operates
• Typical failure symptoms: function won't turn on, won't turn off, or works only intermittently
• Physical clues can include a loose or sticky actuator, heat discoloration, or visible arcing damage

• Disconnect power at the breaker before servicing; allow hot surfaces to cool
• Access the switch per your model's service/parts diagram and note wire positions
• Transfer wires one at a time to the new switch; secure any mounting hardware
• Verify continuity and test operation before reassembly; replace any damaged connectors

This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.

• Monitors door position and allows the cycle to run only when closed
• Interrupts power to stop operation when the door opens
• Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display

• Disconnect power to the appliance before servicing
• Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
• Move wires to the new switch one at a time to maintain correct positions
• After reassembly, test switch operation before running a cycle

The Dispenser Switch is an OEM component for Whirlpool washing machines. Located inside the detergent compartment, it detects when the door is properly closed to enable cycle functions.   

The sensitive switch utilizes durable contacts to reliably connect without false readings due to vibration. Its secure plastic housing contains electronic components regulating additive distribution during selected cycles.

Symptoms of a bad dispenser switch can include:

• Inability to start cycles despite closed door
• Dispenser door fails to lock properly   
• Fault codes relating to dispenser issues  
• Cycles unexpectedly terminating mid-load

Replace yours today with this genuine Whirlpool switch to ensure detergent and other additives activate at optimal times for thorough, even cleaning. Compatible with Kenmore, Maytag, and some Jenn-Air washers.

Fix washer overflow issues with this water level pressure switch. Monitors tub water height and signals controls to stop filling. Common DIY repair.

Washer won't fill properly or overfills? This water level pressure switch senses fill levels and signals when to stop. Easy DIY fix for cycle timing issues.

Fix E32 error codes or washer stopping during fill with this water level pressure switch. Senses water level and controls fill cycles. DIY-friendly repair.

Fix washer overflowing or underfilling issues with this water level pressure switch. Senses tub fill and prevents overflow. 15-minute DIY repair.

Fixes F02 drain error codes and slow draining. This small ball creates a seal in the tub-to-pump hose to control water flow. Simple DIY replacement.

This is a start switch intended for use with dryers. With time or because of damage caused by accident, the start switch may stop working correctly. If the start switch isn't working, then the dryer will not function properly, and a replacement part should be ordered. If the push to start switch doesn't respond, it could be damaged or broken. Replacing the push to start switch on a dryer is a simple process. Start by unplugging the machine. Remove the back panel and pull out the old push to start button. Put the new button in its place and reattach the rear panel. Wear gloves for protection. Restore power only after the complete reassembly is performed. This push-to-start button is a genuine OEM replacement part. It is sold as an individual unit. The part is sourced from the manufacturer and made of durable materials. The push-to-start button can be installed in various dryer models made by SpeedQueen and Alliance brands.