Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Ice maker not filling or water dispenser not working? This water inlet valve controls flow to your refrigerator's ice and water system. DIY repair.
Order new valve Read more
Refrigerator warming up or frost building in freezer? The defrost thermostat monitors evaporator temperature. DIY-friendly repair in under 15 minutes.
Watched a few of your well put together videos and could not afford a new Refrigerator right now because it was a built in so decided with the frost on the bottom of the freezer grill and the Refrigerator warming up decided to replace the Heater Element and Thermostat Defrost which took some time but so far so good lets hope that is all that is needed saved over 10,000.00 dollars for a new 48" built in for now! Thank you for your rushed order and videos I think you are a life saver got the part... Read more
Seals the fresh food door to prevent air leaks, reduce condensation, and maintain temperature. Replace when cracked or loose. Confirm fit with your model.
Ordered new door seals (gaskets) from Appliance Parts Pros. I was able to replace the freezer door seal without taking the door off the refrigerator. (Note: this is an over/under type refrigerator, with the freezer section on top) However, the first attempt at replacing the refrigerator door seal without removing the door from the fridge did not go well as the door appeared "warped" after I reassembled it and would not come close to sealing when I closed it. When I took the door off the fridge... Read more
1/4 inch compression nut for securing plastic water lines in refrigerators and ice makers. Replace worn, cracked, or missing nuts to prevent leaks.
Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks. Read more
Missing or cracked ice bin? This replacement ice cube pan restores contained ice storage in your refrigerator's freezer. Simple slide-in installation.
Had the parts I needed at a lower cost Read more
This ice maker shut-off arm is the wire lever that detects the ice bin level and stops production when raised. Replace a bent, broken, or missing arm to restore reliable on/off control of your icemaker.
Ordered a new ice maker from APP. All went well, did not think to keep shut off arm from old ice maker before I trashed it. Got lots of ice now. Read more
Metal support bar that mounts to the refrigerator liner to hold the crisper cover frame and glass level. Replace if broken, missing, or bent.
I had to cut down the length of the bar using a Dremel so that it would fit into the channels, it was originally too wide to fit into the fridge. One thing to note, only cut it as wide as the actual fridge; you can get it into the plastic shelf structure by sliding it too much into one side, and then guiding it into the other side. Read more
Refrigerator freezing food or not cooling? This temperature control thermostat regulates cooling cycles. Common DIY fix when temps won't stay consistent.
Ordered a cold thermostat switch and installed it. Read more
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more
This is a small white plastic plug that fills the hinge sleeve hole on a refrigerator or freezer door. It covers unused hinge mounting holes to provide a clean, finished appearance, especially after reversing the door swing. Replace this plug if it has cracked, fallen out, or gone missing, leaving an exposed hole in the door.
Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more
This is a rubber gasket that seals the connection between the water fill tube and the ice maker assembly inside the freezer compartment. It prevents water from leaking around the fill tube during the ice maker's fill cycle. Replace this gasket if you notice water dripping or ice buildup around the fill tube area, or if water is leaking onto the freezer floor during ice production.
I ordered the repair parts that Lowes said they couldn't get. I got the parts very fast and only took 5 minutes to get the job done. Read more
Fridge not cooling but lights work? This compressor overload stops overheating and prevents startup damage. DIY-friendly repair in about 1 hour.
Replaced overload switch and start relay with convenient repair set.Video available on website that gave step by step instructions. Followed the video steps for removal and installation.... plugged in the refrigerator compressor started up everything cool in minutes Read more
Fix dim or no interior lighting with this refrigerator light bulb. Restores clear visibility when you open the door. Simple 5-minute replacement.
Replacement mounting screw for refrigerator panels, brackets, and trim. Restores secure fit when original screw is stripped, missing, or damaged.
REPLACED THE 4 BRACKETS FROM BOTH THE REFRIGERATOR AND FREEZER DOOR(S) HANDLES. Read more
Mounts in the dispenser to secure the ice housing assembly. Keeps the chute and door aligned for smooth dispensing. Replace if cracked, broken, or worn.
Replaced the ice tray and motor mount plate. While I was there I replaced the thermostat also. New parts arrived in a day and a half. Read more
Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:
Checked out the video on your site on how to disassemble the ice maker. Was really easy when you know the correct sequence. Only 3 screws and it's out of the freezer. Disassembled the ice maker on my kitchen counter and replaced the ice stripper. Reassembled and installed back in my freezer. It is as good as new Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.