A515 Parts

This adjusting nut threads onto an eyebolt to set and lock an adjustment point. It helps maintain proper tension or alignment in the mechanism so the appliance operates smoothly without the setting drifting over time. What it does:

• Threads onto an eyebolt to fine-tune and secure an adjustment
• Helps prevent vibration from loosening the setting
• Replaces a stripped, rounded, or missing nut so adjustments hold
• Visual cues for replacement include damaged threads or worn hex flats

• 1 adjusting nut

• Disconnect power; turn off water or gas supply if applicable
• Components attached to eyebolts may be under spring or mechanical tension—support and relieve tension before removal
• Mark or measure the original setting to match during reassembly
• Start by hand to avoid cross-threading; tighten securely without over-torquing

A small replacement retainer clip that secures panels, trim pieces or small hoses to prevent movement and rattling. Replaces worn or broken clips to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance trim, panels or lightweight components to the cabinet or chassis
• Prevents rattling, vibration noise and misaligned panels caused by a missing or damaged clip
• Holds wiring looms or small hoses in place on select appliance models
• Restores OEM fit where original clip has broken, bent or fallen off

• Disconnect power (and water, if applicable) before servicing the appliance
• Small part — a flat-head screwdriver or needle-nose pliers may be helpful for removal/installation
• Handle sharp edges on panels and wear gloves and eye protection as needed

This pin collar is a small retaining fastener that secures a shaft or component in place, preventing lateral movement and keeping assemblies aligned for reliable operation. It's a simple replacement to restore proper fit and function. What it does

• Retains shafts, pins, or small components to prevent sliding or separation
• Helps maintain alignment of moving parts for smooth operation
• Commonly replaced when parts shift, wobble, or fall out of position
• Works as a low-profile mechanical stop in various appliance linkages

• Pin collar (single)

• Disconnect power to the appliance before beginning any repair
• Verify orientation and seating against the mating part; install so collar fully engages the shaft or groove
• Use appropriate tools and avoid hammering or forcing the part to prevent damage
• Reinstall retaining rings or additional hardware in the original order

This idler pulley guides and maintains tension on the dryer drive belt to help the drum rotate smoothly. Replacing a worn pulley restores correct belt tracking and reduces noise from rubbing or slipping. What it does

• Guides the dryer drive belt and keeps proper belt tension
• Helps the drum turn smoothly during normal operation
• Commonly used when you hear squeaking, grinding, or belt slipping noises
• Prevents premature belt wear and misalignment

• One idler pulley

• Disconnect power before starting any repair; the appliance is de-energized
• Basic hand tools required; remove the front or access panel and drum as needed per your model's service instructions
• Inspect the belt and bearing surfaces; replace belt if damaged or glazed
• Do not lubricate the pulley unless the OEM specifically directs it; replace if bearing is noisy or seized

Replacement 3/8-16 nut that secures bolts and threaded shafts in appliance assemblies. Needed when original nut is stripped, lost, or corroded.

Replacement nut and bolt fastener for laundry center components. Secures panels, brackets, and assemblies. Order when hardware is missing or stripped.

Leaking water connection? This hose coupling creates a secure seal between your washer hose and water inlet, stopping drips and loose connections. DIY fix.

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A

Replace worn, stripped, or missing 8-18 x 3/8 machine screws that secure control panels, trim pieces, and brackets on your appliance. Restores tight fit.

A single mounting screw designed to secure panels, brackets, or components on your appliance for reliable fit and reduced vibration. Use this genuine replacement when a fastener is missing, stripped, or rusted. What it does:

• Fastens panels, trim, or mounting brackets to restore proper alignment
• Helps eliminate rattling or vibration caused by loose or missing screws
• Replaces corroded or damaged hardware to maintain safe operation
• Restores secure attachment for parts that no longer hold in place

• Disconnect power to the appliance before starting any repair
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid overtightening which can strip threads or damage parts

A replacement nut-lock used to secure fasteners and keep panels or components from backing off due to vibration. Simple, durable hardware that restores a secure connection and reduces rattling or loose parts. What it does:

• Secures a mating bolt or stud to prevent loosening from vibration or movement
• Restores a solid attachment for panels, brackets, or assemblies that may come loose
• Helps eliminate symptoms such as rattling, vibrating, or intermittent panel movement
• Suitable where a locking fastener is required to maintain a reliable connection

• Disconnect power and follow appliance safety procedures before starting work
• Locate the matching stud or bolt and remove the old fastener if present
• Use the correct-size wrench or socket and tighten until the nut-lock seats; avoid over-tightening
• Inspect threads and mating hardware for damage; replace damaged components

Washer won't drain or drains slowly? This pump belt transfers motor power to the drain pump. Direct-fit replacement restores proper drainage in 15-30 minutes.

Export motor.

Connector for washer water supply lines. Replaces cracked, corroded, or leaking connectors. Essential for secure installation and proper water flow.

Mounting screw for refrigerator assembly. Secures components and panels in place. Replace if screw is stripped, missing, or no longer holding tight.