Abd7600aww Parts

• Not dispensing water
• Leaking

Being an ex maintainence. person, I went down and turned off the water supply. Then I started to try to find the leak by removing the rear covers for the compressor and valves. Once removing a couple of covers where the dual valve was, I spotted where the water was coming from.I then pulled the electrical plug from the wall. Between the solenoid and valve. I removed the screws that held the valve in place. Then disconnected the three hoses going into valve and removed the two electrical... Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

Ordered the piece and put it in the refrigerator. Read more

Touch up paint Read more

Replaced It With New One Read more

• Freezer not defrosting
• Freezer too cold
• Fridge too warm
• Freezer section too warm

After we moved into our new home, we realized that the freezer was very cold and the fins were frosting over, and the refrigerator wasn't cold. We had to take it apart and manually defrost it about once every 8 to 10 days. After research online, we found Appliance Parts Pros videos, which clearly explained how to fix it ourselves, a savings of at least $1,000 or more, since a new one of this size would have been in the arena of $1,200 to $2000. We ordered the three most likely parts to be bad,... Read more

Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more

• Not dispensing water
• Ice maker not making ice
• Leaking

I watched your how-to video. It explained the repair PERFECTLY. It was an easy repair and the video was very detailed. It took the guesswork out of the repair. I was done in 5 minutes. thanks for taking the time to post videos for your parts. I'll shop here again. Best Regards, Chad M Read more

Very easy.Just set right in Read more

I replaced the thermistor and the damper control. I couldn't have done it without the videos showing me how to get stuff apart Read more

I watched the video on how to replace the ice maker and the replaced it with zero problems. Excellent help in trouble shooting problem and installation video further assisted in ease of installation. Read more

• Freezer not defrosting

My unit has a bottom freezer that is a drawer. I had to remove the drawer, rack, glides, glide tracks, and ice maker to remove the rear panel. This was a little difficult but after researching a few videos on line I learned some tricks that made it easier. I used a hair dryer to melt the ice. This is best done with 2 people having one at the back to sponge the water into a bowl from the pan to avoid a water mess. Using a bolt meter I checked the heating element and found it had continuity. I... Read more

If you have a problem of water pressure when you press for water at the dispenser your problem migth be your filter head assembly. Thanks to appliAncepartspros for their assistance Read more

There are videos on You Tube,. After removing the bottom basket, you remove the entire drawer including the door together with it, by using a screwdriver to depress the white clip on each drawer slide which releases the slide from body of the freezer. Once you pull our the entire drawer, you will need to drill out a rivet to remove the old slide. You will need a rivet gun to attach the new slide. Read more

Used screwdriver to push in plastic tabs holding old unit to the top of the refrigerator box Read more

I had verified that the water supply was healthy, so it was either the icemaker unit or the water valve. I replaced the icemake first, based on a the pareto showing it was the culprit for most other people, but it didn't help. That replacement was straightforward; the hardest part was reaching all the way back to unclip the wiring harness since I am too lazy to totally empty the bottom freezer and remove the door. So the next step was the water valve. The hardest part of this was pulling the... Read more