Afd2535fes Parts

• Ice maker not making ice
• Ice maker won't dispense ice

SO I FIGURED THAT ALL THE MECHANICAL PARTS OF IT WERE FINE SO THE LOGICAL THING TO DO WAS TO REPLACE ELECTRICAL COMPONENTS WHICH CONSISTED OF THE THERMOSTAT {THE BRAIN} AND THE CONTROL MODULE WHICH I PURCHASED AT A VERY REASONABLE PRICE . I REASSEMBLED THE UNIT AND IT HAS BEEN WORKING LIKE NEW EVER SINCE. THANK YOU! Read more

I looked up the parts online at AppliancePros.com! To my surprise, the detailed drawings showed that I could replace the center rail (about $13) instead of the entire lower shelf (about $100)! I also ordered a replacement shelf bin that had broken. I looked at other sites for the parts, but they were cheapest here. I ordered the parts LATE Wednesday and they were at my door Friday afternoon! Super fast! The order was accurate, packed well so it arrived damage free, Read more

• Ice maker not making ice

I used your online troubleshooting tips and watched the videos on your site. I determined my thermostat was defective, ordered the thermostat which arrived in two days and I replaced the thermostat and I now have a full bin of ice !!! The do it yourself video was extremely helpful and made the repair very easy. Thanks so much for the great service and quick delivery !!! Read more

I searched online for replacement parts and Appliance Parts Pros had the part in stock. Before I ordered the part, I watched the video to see if I could handle the repair. I ordered the part and soaked the gaskets with warm water in the tub. The old gaskets had a much simpler setup, so no cutting was involved. I simply pulled the old gasket out of the track without issues, and installed the new one with finger pressure. Per the video, I took both doors off. However, due to the design, I could... Read more

Replaced water valve and ice maker Read more

We turned off the circuit breaker. We then removed the light cover and then the control panel. We disconnected the Keyboard, Utah, plugged in the new one and turned the breaker on to see if everything worked. We realized that we did not need a new jazz board so that is being returned. The old Keyboard was removed, the new one attached and all the parts were put back. The frig works fine now at the recommended settings of zero and 38F. Read more

1. Ordered new gasket. 2. Heated with blow dryer gasket until it resumed its normal shape. 3. Turned off refrig. 4. Cleaned freezer compartment. 5. Removed old gasket. 6. Installed new gasket. 7. Turned on refrig. 8, Operation back to normal in about 6 hours. Read more

• Freezer section too warm

The fan has a very thin wire in it's coil, and when that wire breaks, you need a new fan. In a previous repair, i noticed that an ice build-up had dislodged the wiring on my fan and severed the coil winding. I was able to undo the winding a couple of turns and get it working again. But more recently, the fan stopped and there was no repairing it. So i ordered a new fan from AppliancePartsPros.com and it got here in very good time. The new fan was slightly different as the prongs seemed to be... Read more

We were experiencing slow water flow from our Whirlpool interior water dispenser. The water would flow normally for a couple of seconds then subside to a trickle. After replacing the water filter and inlet valve, research suggested that the water filter head could be the culprit. In about 30 minutes, I was able to remove the old part and replace with a new part solving the problem. Read more

• Fridge too warm
• Noisy

I determined that the motor that drives the damper valve that allows cold air into the refer was noisy. I ordered the replacement part from AppliancePartsPro.com. It arrived within 3 days and I changed the units out, which took about 10 minutes total. All is quiet with the refer now. Read more

No instructions are included with either piece, which makes installation take more time and care. Tools needed: Small standard flat blade screwdriver, box knife or other knife with at least a 2" long blade, super glue. Remove the old main crisper frame: 1. Remove old main frame by lifting upward and outward. 2. Remove the center rail from the frame. May require bending of the main frame to remove it. 3. Remove the crisper front panel by unsnapping from frame. This is easily done by... Read more

• Freezer not defrosting
• Fridge too warm

Toughest part of this repair is figuring out how to get things apart. Amana doesn't provide you a repair manual showing how to disengage the various plastic covers. Initially disassembled the bottom freezer compartment so I could get to the evaporator coils; they were completely frozen in block of ice, restricting air flow to the fridge above. Obviously, the auto defrost cycle had not been running, or was short-cycling. Manually defrosted. Found this link for running diagnostic tests on the... Read more

Replaced the defrost thermostat and heater and the refrigerator was working again. Read more

Pulled out storage bin Removed side track rail covers Popped off gear from holding clip Installed drive shaft Installed rail cover and storage bin Only took about 15 minutes Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more