Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Washer only fills with hot water or stops mid-cycle? The water temperature switch controls incoming water temps for proper cycle selection. DIY repair.
I tested the Atc. mid level switch, with my multi tester and found it was not sending enough current to the cold water inlet valve, so it would not open and let cold water in. I replaced the switch, (it was a snap) literally it snapped in place. replace the front face and turned the water back on and plugged in the washer, and turned it on. It worked perfect and has been since. good and easy repair even for a novice like me.. Read more
Used to lock washer cabinet to rear wall of washer.
Replaced springs and the ordered clips holding the control panel to the washer outer cabinet. Clips had been elongated from earlier repair work. A DIY tutorial was a great help. Read more
Washer motor shield deflects water, lint, and debris away from the drive motor. Replace if cracked or missing to prevent motor damage. Simple install.
Washer won't stop spinning smoothly or makes loud jerking noise when stopping? The brake shoe stops the tub during spin cycles. DIY repair in 1-2 hours.
First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine. Read more
Structural bracket that secures the rear panel to the washer chassis. Replace if cracked, broken, or missing to restore proper alignment and cabinet stability.
In the end, with a new coupler. But I relearned old lessons the hard way. The washer is in a rental unit and the tenant complained of no spin. My first intuition was that the coupler failed again because I bought a cheaper one elsewhere a couple of years ago and not the brand name available here at AppliancePartsPros. But we’ll come back to that. Lesson #1: Verify the symptoms firsthand. I dug in right away, popped out the motor and the coupler appeared okay. When I spun it by hand, it turned... Read more
The Whirlpool spacer is an OEM replacement part responsible for maintaining the proper spacing and alignment between the washer cabinet and the top panel. The spacer provides stability and support to the appliance. It ensures that the top panel is securely attached and evenly distributed, preventing any misalignment or instability during operation.
Causes of a bad spacer can include wear and tear over time, physical damage due to accidental impacts, or deformation from prolonged use under stress. These issues can lead to misalignment and operational inefficiencies in the appliance.
Symptoms of a bad spacer include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. Sold individually, four are needed to replace all parts. Screw part number WP3390631.
Washer thrust ring acts as a bearing spacer between the outer tub and basket drive, controlling end-play and reducing friction. Replace when worn to restore smooth, quiet operation and prevent premature wear.
Purchased parts from your site and did a self repair. Excellent quality , speedy delivery and easy to install. Now our 13 year old washer works as good as new. Read more
Rubber grommet for motor mount stud.
Replaced dog ears. Read more
This 1-1/8 in wire retaining ring locks into a groove to secure components in place. It helps prevent parts from sliding off a shaft or shifting out of position so assemblies stay aligned and operate reliably.
Based on recommendation to replace the clutch if clothes aren't spinning dry enough, I ordered a new clutch. Upon disassembly, I observed no Ring Wire/C-Clip and that the bearing appeared worn. Where did the clip go? Well, the bearing wore down such that it wore out the clip and bearing up to the sleeve of the shaft. Knocked out the old bearing, tapped in the new and was done. I disassembled the brake shoes but believe you can get the bearing in and out without doing so. Not a bad job, just... Read more
10 - 16 x 1/2
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair... Read more
Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.
Bought a new cord and removed the back of the washer and unclipped the old and clipped in the new. 5 minutes tops. Read more
Replaces the upper tub ring that mounts on top of the outer tub as a splash guard. Order a new ring if yours is cracked, broken, or no longer securely attached.
This was the second attempt at fixing this problem. The first repair and parts were generated by listing the problem and reviewing the potential corrections, listed on the web site. From making repairs on other clothes washers, I was confident that some of those potential causes could have been the cause. Unfortunately the counterbalance spring and suspension springs were not the cause as they were attached as intended and in good condition. I reached out for Appliance Parts Pros input... Read more
Replace your washer's cracked or leaking outer tub. This housing holds the inner basket and prevents water from leaking into the machine's interior.
Replaced tub and center post seal Read more
Secures the motor to its mounting point in your laundry center. Replace if the retainer is worn, broken, or has lost tension to prevent motor misalignment.
Replaced with new retainer clips and new capacitor to fix future problems Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.