Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replaces a cracked, broken, or clogged lower spray arm in your dishwasher. Installs at the bottom of the tub. Needed when spray holes are blocked or damaged.
I replaced a few key parts that I couldn't clean properly, and were not spinning well in the dishwasher. Afterwards, it worked like new, and the cleaning power returned. Read more
Insulation blanket that wraps around the dishwasher tub to reduce noise and maintain temperature. Replace if damaged, torn, missing, or contaminated.
I pulled the DW out, pulled off the old blanket pieces, vacuumed up the millions of small parts, then put the new blanket on, I did use some packing tape to hold it in place. Easy! The challenge was moving the unit out, then back in, but that was simply time and a little effort. Read more
Replacement drain hose kit for dishwashers. Flexible tubing routes wastewater from the wash chamber to the pump outlet. Replace if cracked or leaking.
Our GE was installed about 8 years ago and was AWESOME for much of its early life. However, progressively its cleaning ability diminished. By replacing all the spray arms (clogged with debris), filters, drain hose, and sump...this dishwasher cleans like it did when it was new! Cost was around $100 (also replaced a wheel and the silverware basket) and labor was relatively simple. And to think...my mother-in-law said, "Wouldn't it just be easier to buy a new one?!?". Read more
Replace your dishwasher's side trim gasket to prevent water leaks along the door edges. Install when you notice leaking or difficulty closing the door.
New seal. Read more
Fix low spray pressure, growling noises, or leaks from the pump housing. This circulation pump assembly requires basic tools. Takes 1-2 hours to install.
I ordered a new motor through ApplianceParts Pros.com and had the new part within 5 days. The entire replacement took approximately 1 1/2 - 2 hours. The repair was relatively simple and straight forward. By doing the work myself I saved over $250. Originally a GE technician quoted a price of $489 to replace the motor to repair the dishwasher. For that price I could have bought a new dishwasher (Electronix Express $491) but not with all the features of my current appliance. By doing the... Read more
Fix dishwasher leaking from pump housing with this impeller & seal kit. Repairs worn seals causing water leaks. DIY-friendly, typically 30 minutes.
Replaced pump impeller. Read more
Upper dishrack assembly for dishwashers. Holds dishes and cookware on top rack. Replace if rusted, cracked, or plastic coating is peeling. Includes rollers.
I made my first order with just the make (GE) and Model (Monogram) What was shipped first appeared to be a generic GE rack set. I read some other folks post and some said they made minor adjustments to these racks and they worked fine. I was not happy with the fit and returned the first set. The next set was ordered with Make, Model and Serial number. What was shipped this time are direct replacements for the original racks. A perfect fit. My bad for not including enough information on my... Read more
Roller bearing cage installs in the dishwasher rack track to support smooth gliding. Replace if cracked, broken, or causing the rack to stick or slide out.
I did not see the old ones fall out, so I was not sure the exact product placement within the rail, which was frustrating, to say the least. For the next person's benefit....these slide into the MIDDLE of the rail that is attached to both sides of the dishwasher. Not the front, not the back, but the middle! Steps to fix: 1) Order 2 of these Roller Bearing Cage. 2) Order 4 of WD12X10304 (AP4484666) end caps!! Unless you have brand new ones already, you will need them for sure and they are... Read more
Pulley component for dishwasher door hinge system. Installs behind door panel to provide tension and balance for smooth opening and closing. Replace if cracked, broken, or worn.
At first it seems that the pulley can't be removed to make this repair. However,after removing the screw that holds the pulley in place, if you take a small screwdriver and tap the center of the pulley bracket with a hammer it comes out from behind and will go back in with hand pressure after repair. Read more
Secures the upper spray arm to the dishwasher tub ceiling. Replace if missing, stripped, or broken to properly lock the spray arm in place.
Went ahead and replaced the arm and bolt/bushing. Read more
The screw is an OEM replacement component for GE dishwashers. It is used to securely fasten parts inside the dishwasher tub assembly.
Causes of a damaged or defective screw usually involve wear from continuous mechanical stresses and vibration during dishwasher usage. Loose parts affect machine balance and performance.
Symptoms of a compromised screw placement include:
This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
The replacement of the arm took a total of 3 minutes, all I needed was a nut driver for the easy job, taking the old arm out and putting the new one in, exact replacement , I appreciate you getting the part out as fast as you did. It took an extra day because of the ice storm we had . That was ok. Thanks you . Read more
The Check Valve Flapper is an OEM replacement part for GE dishwashers. It is a small but crucial component located within the water inlet valve assembly. The check valve flapper regulates water flow into the dishwasher, allowing water to enter during the fill cycles but preventing backflow when the water is drained.
Causes of a bad check valve flapper can include wear and tear over time, mineral buildup that causes sticking, or damage to the flapper itself. This prevents the flapper from opening and closing as intended.
Symptoms of a bad check valve flapper include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore dishwasher models.
Pulled dishwasher from the cabinet and flipped onto its side. Easy access to sump and drain flapper valve that I also replaced. Rubber sump coming apart into soft pills & chunks and plugging spray arms. Better now but it's rediculous that GE would make components that dissolve this way. Read more
Fix a dishwasher that won't drain completely with this drain pump assembly. Common causes include worn impeller or blockages. DIY-friendly repair.
I had clogs before, so I knew this wasn't the case. When I tried the "rinse and hold" setting, the water would fill, but no sound when it tried to drain. I suspected the pump. Searching through YouTube, I found a helpful video for the GE Profile unit. In fact, the video directed me to this site for parts. It seemed simple enough to replace and I verified the part number to order. I pulled out the dishwasher, laid it on it's side, swapped the part, put it back in, and tested. It now works... Read more
The Blower Motor Assembly is an OEM part for GE dishwashers. This part is responsible for driving the dishwasher's venting system, which plays a key role in the drying process of your dishes. Over time, the Blower Motor Assembly may need replacement due to wear and tear, damage, or failure. A malfunctioning blower motor can lead to ineffective drying of dishes, increased cycle times, or the dishwasher failing to complete its drying cycle properly. Symptoms of a bad Blower Motor Assembly include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
I had a repairman in to check why machine had no power. I watched as he opened the door up and secured the electrical ribbon in place and lights on control panel came on. Asked him questions about the noise he confirmed it was the blower. would have charged me around $250.00 to replace that. Spoke to a rep on the phone and ordered the part for $100.00. The replacement part arrived in 1 day. Looked at the parts diagram on your site to orient myself. Separated the the front door( screws)... Read more
Dishwasher leaking from underneath? A cracked or worn check valve assembly often causes pooling water. DIY-friendly repair takes about 30 minutes.
I ordered the part plus I replaced all of the other rubber/plastic parts just in case. My dishwasher is ten years old and still works great. Read more
Replaces a broken, cracked, or melted lower spray arm in your dishwasher. Installs on the bottom rack level to rotate and distribute water during wash cycles.
Just popped it in, easy as pie. Read more