De4000ayq Parts

I took off the front cover and checked the sensors which were all good. Then I removed the cover for the heating coil after finding that it appeared open. Found that the coil had in fact broken but the break was not visible just by looking in. Located the break in the coil within an insulator near the back. I checked appliance stores locally and found the coil for far more than Appliance Parts Pros wanted for it. I placed an order after chatting with a tech, I placed and order and had it in... Read more

• Won't start

Through 15 years of vibration, the Cycling Thermostat evidently had degraded to the point where one electrical connection or more came loose and caused a short. There is also a possibility that the Bakelite section of the Dryer Cycling Thermostat body separated from the metal base, simultaneously exposing all four connections to a short. The thermostat literally exploded into chunks and dust. There was a heavy arcing and then, thankfully, the thermal fuse blew and shut down power to the short... Read more

• Door won't close

Took off front cover of drier, removed old part and just snapped in new part. Read more

• Won't start
• No heat or not enough heat

Did some dryer repair research (dryer not heating) on the internet. Bought an ohm meter, opened up the dryer and tested the cut-off-T, high limit thermostat, dryer igniter, flame sensor, cycling thermostat for continuity. The igniter was bad, the other parts tested ok. Went online to AppliancePartsPros.com searched for a new igniter for my specific dryer model, found the right replacement igniter and watched the video on how to replace the igniter. Because my dryer is old (15+ years) and I... Read more

Our dryer suddenly began overheating while drying. Outside of the dryer cabinet was uncomfortably warm to the touch, dryer drum was hot, charred smelling laundry. Based on what I read it was likely one of two things - a failed cycling thermostat or a shorted heating element. First I cleaned the vent hose and ducting to ensure good airflow, which I had. I opened the circuit breaker first, then took off the door and front cover. I started with a thorough cleaning of the dryer with a vaccuum... Read more

Found the parts in the diagram of my fridge and simply installed it very easy Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

It took me about 2 hours to take everything apart and get it back together & running again with no problems. All the parts I ordered were exactly what I needed to fix everything. Thank you all !!! Read more

• Too hot

I removed the front panel and observed the heating element while running the dryer. It was cycling off every minute or so and staying off for several minutes. Even though it was likely the high temp cycling thermostat I replaced both the 14, and 15 cycling thermostats which I think are the original factory units. That makes them nearly 35 years old. Problem fixed. Read more

First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more

I figured there could only be a couple reasons why the dryer would not heat so I did some research. I read where you could test for continuity on the parts to determine which one was bad. A friend referred me to this site, I looked up the part for my particular model, ordered and replaced the part. It could not have been any easier. I will come back to this site with my future appliance parts needs for sure! Read more

• Noisy

Replaced them. Read more

I replaced the motor and all other moving components along with the felt drum seals.drum glides and drive belt. The wiring instruction is where i had the most problems. Because my wiring had only 4 wires in the harness not 5, and one was a different color then the instructions call out, I believe was because it might have been and older model. the instruction called for a gray wire but mine was white with a blue piggy back wire attached. but after finding a few videos on line i figured that the... Read more

I ordered all the parts necessary to replace the heating element and thermostat on a Sunday night. Appliance Parts Pros shipped on Monday AM and I received them on Wednesday. It took me 45 minutes to disassemble the dryer, replace the parts and have the dryer working again. It should be good for another 35 years which should cover me for my needs. Thanks again to Appliance Parts Pros for having the best service and always the correct parts. I am a huge fan of your company as you never... Read more

Took the front panel off (the door front), disconnected the connector to the door switch and used a wooden clothespin to bypass the door switch. Turned on the dryer to locate loud squeaking sound and found it was coming from the motor area. When I started to take the blower section apart from the motor, that is when I saw the "blower wheel" slipped off the motor shaft. The blower wheel has a "C" clip retainer and compression ring to keep it snug on the motor shaft (but it was loose). Now I... Read more

Replaced dried crumbling rubber foot. Cleaned inside and outside of dryer before installing igniter cleared vent hose. Leveled unit installed dryer igniter. Fired it up.Runs Great Now. Read more