Dmt300rfw/Xac Parts

• Leaking

I just had to pull the old out and push the new one in. Read more

• lights flashing or blinking

Since my Samsung Dishwasher would not drain and had a flashing quick light, I removed the racks and both spray wands. Which allowed me to remove the lower screen assembly. This revealed a worn and broken check valve and broken grinder blade. I cleaned the inside of the dishwasher and removed the unit from under the counter. I removed and cleaned the brake assembly ( large transparent plastic section on left side of the dishwasher). I cleaned this for preventive maintenance by taking the float... Read more

Bought 2 new wheels and it works perfectly. Yay! Read more

Since my Samsung Dishwasher would not drain and had a flashing quick light, I removed the racks and both spray wands. Which allowed me to remove the lower screen assembly. This revealed a worn and broken check valve and broken grinder blade. I cleaned the inside of the dishwasher and removed the unit from under the counter. I removed and cleaned the brake assembly ( large transparent plastic section on left side of the dishwasher). I cleaned this for preventive maintenance by taking the float... Read more

Went to appliancepartspro, looked up my model # and make. What's amazing is the parts arrived in 1 day. Shipping was SUPER FAST, the emails advising on shipping were in the money. Received the wheels, popped them in, took 3 minutes to open package and install the wheels. Dishwasher bottom rack is gliding smoothly like new. Read more

After researching the Internet, I thought the drainage hoses were my problem. First I changed both drainage hoses. That didn’t solve the problem. I had to look for another area that was causing water to drip into the pan. I found water leaking from behind the brake assembly. Since I didn’t get an oE error code, I eliminated the brake assembly as causing my problem. I ordered a brake gasket and cover. Once I got it properly installed, problem solved! Read more

Bracket has side mount on dishwasher and then screwed into cabinets on both sides. Read more

While waiting for a replacement PCB, I cleaned the filter and soaked up the remaining water in the tub (dishwasher died mid-cycle) which entailed removing the dishwasher mesh filter and cover assembly of the pump assembly. The filter seal in the cover assembly and seal in the case scroll popped out. These two gaskets (seals) somehow had stretched and were very difficult to keep in their tracks while reassembling the pump assembly after cleaning. Replacement gaskets fit much better than the... Read more

I replaced both items. I lifted the racks out for clearance. with a small screwdriver, I flexed the flat springs holding the whole tube assembly. It came right out. Using the screwdriver, I popped the nozzle off, put the new one. I flexed the flat springs a little back into line to be able to hold the whole tube assembly, put the assembly back in, and pushed the spray arm onto the nozzle. Put racks in. done. Took less time than it did to write this fix it paragraph. Read more

I replaced both items. I lifted the racks out for clearance. with a small screwdriver, I flexed the flat springs holding the whole tube assembly. It came right out. Using the screwdriver, I popped the nozzle off, put the new one. I flexed the flat springs a little back into line to be able to hold the whole tube assembly, put the assembly back in, and pushed the spray arm onto the nozzle. Put racks in. done. Took less time than it did to write this fix it paragraph. Read more

Research indicated that it may be a moisture sensor failure or a leak. It ended up being a leak from the oil seal on the motor shaft. A small piece of plastic made it's way into the system. The hot water softened it enough that it wrapped around the motor shaft, re-hardened, then tore into the shaft seal. I fixed it by replacing the shaft seal, moisture sensor (corrodes when it gets wet), and replaced the sump seal since I had it disassembled. Read more

• Will not dispense detergent

Removing the door panel was easy -- remove 6 Torx screws, and the panel falls off. Next you need to remove an electrical plug and 2 individual wires from the old dispenser. The plug came right off, but the wires were not easy to access, and they fought me more than I expected. With some pliers and wiggling, they eventually let go and came free. The dispenser is held in place with 6 Phillips screws through 2 removable metal brackets, and those came out easily. The toughest part of the job... Read more

While waiting for a replacement PCB, I cleaned the filter and soaked up the remaining water in the tub (dishwasher died mid-cycle) which entailed removing the dishwasher mesh filter and cover assembly of the pump assembly. The filter seal in the cover assembly and seal in the case scroll popped out. These two gaskets (seals) somehow had stretched and were very difficult to keep in their tracks while reassembling the pump assembly after cleaning. Replacement gaskets fit much better than the... Read more