Du1010xtxbo Parts

This left-hand door hinge supports and pivots the door so it opens smoothly and closes tight. Replace a worn hinge to correct sagging, rubbing, or doors that won't seal—improving performance and preventing damage. What it does:

• Provides the pivot point for the door on the left side
• Maintains alignment so the door sits level and latches/seals properly
• Helps the door open and close smoothly without binding
• Common symptoms: door sags or rubs, won't close fully, uneven gaps, squeaking/grinding noises, poor seal

• One left-hand door hinge

• Disconnect power; also shut off gas and/or water before servicing
• Support or remove the door before unfastening the hinge; some hinges may be under spring tension—use caution
• Transfer original hardware/shims as needed and tighten fasteners securely
• Check door alignment and gasket contact after installation; open/close several times to ensure smooth operation

• "Left-hand" is determined when facing the front of the appliance.

Right-hand door hinge that replaces a worn or damaged refrigerator door hinge to restore proper door alignment and smooth opening and closing. Helps maintain a tight seal and prevents door sag or binding. What it does:

• Supports and pivots the refrigerator door on the right-hand side for correct alignment.
• Restores smooth opening/closing and reduces rubbing or scraping at the cabinet.
• Helps re-establish a full door seal to prevent cold air loss and temperature issues.
• Addresses symptoms such as a sagging or misaligned door, noisy hinge movement, or a door that doesn't close evenly.

• Disconnect power to the appliance and remove any items from the door before starting.
• Support the door while removing hinge hardware to prevent sudden drops or damage.
• Reuse existing screws/hardware unless replacement hardware is provided; tighten securely but avoid over-torquing.
• After installation, check door alignment and gasket contact; adjust hinge position as needed to ensure proper sealing.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

The Filter Screen is an OEM component specifically designed for Whirlpool dishwashers. Located inside the sump area, the durable mesh screen captures small food particles and debris before wash water is recirculated through cycles.

Symptoms of a bad filter screen can include clogging obscuring openings over time, degrading mesh no longer inhibiting passage, or dislodging from mounting points allowing bypass.

Causes involve the normal accumulation of soils requiring periodic cleaning. Mineral buildup may eventually cement sections together reducing effectiveness. 

Symptoms of a bad filter screen include:

• Dirty or soiled wash water unable to fully circulate  
• Filth dispersing throughout the wash cabinet interior
• Reduced cleaning and unsatisfactory dish results

This OEM Whirlpool part is also compatible with KitchenAid, Maytag, Jenn-Air, Amana, and some Kenmore dishwasher models. Replace to maintain built-in wastewater filtration protecting major components.

This brace connector is a small structural support that secures and stabilizes appliance components, helping maintain proper alignment and reduce vibration. It restores firm attachment where a worn or broken connector causes movement. What it does:

• Secures joining points between panels or assemblies to prevent looseness and rattling
• Restores proper alignment of connected parts so doors, panels, or controls operate smoothly
• Helps reduce vibration and noise caused by a failed or missing connector
• Works as the replacement structural fastener specified by the manufacturer

• Disconnect power (and water if applicable) before beginning any repair
• Basic hand tools (screwdriver, socket) typically required; inspect mounting hardware and replace if damaged
• Verify correct orientation and tightness during installation to avoid stressing adjacent parts

Color: Black - Part has been changed to an Access Panel Kit - The toe panel is no longer used.

This electronic control board is the appliance's central control. It interprets inputs and controls power to key components, helping restore normal operation when the original board is faulty.

• Coordinates timing and power to motors, valves, heaters, fans, and lights
• Processes signals from sensors and the user interface to run cycles
• Stores control logic and diagnostics to manage operation
• Failure symptoms can include: won't start or power up, unresponsive or erratic controls, cycles that won't run or complete, persistent error codes

• Disconnect power and verify no voltage before servicing
• Use ESD protection; handle the PCB by the edges to prevent damage
• Note/photograph all wiring and connectors; transfer any brackets, jumpers, or guides from the original board
• Some models require service-mode setup or programming after installation—refer to your unit's tech sheet or service manual

This run capacitor helps start and keep the motor running smoothly by providing the necessary phase shift and torque boost. A weak capacitor can cause hard starting, humming, or intermittent motor operation.

• Supplies continuous phase shift to maintain motor rotation
• Helps the motor start reliably under load
• Symptoms can include humming, slow or no start, or overheating shutdown
• Restores normal operation when the original capacitor has weakened

• Disconnect power before servicing; discharge the old capacitor safely
• Note wire locations and transfer leads to the new capacitor one-by-one
• Mount securely in the original bracket or location to prevent vibration
• If the motor still won't start, further diagnosis of the motor or start device may be required

This connector links mating components within the appliance to create a secure, reliable connection. Replacing a cracked or loose connector helps restore consistent operation and prevent intermittent issues caused by poor contact or separation. What it does:

• Creates a stable connection between mating parts or harnesses in the appliance
• Helps prevent looseness or separation that can disrupt performance
• Direct replacement for broken, brittle, or deformed connectors
• Can resolve intermittent operation traced to a poor connection at this junction

• 1 connector

• Disconnect power and, if applicable, shut off water before servicing
• Note orientation and positions before removal to ensure correct reassembly
• Seat the connector fully until any locking features engage; do not force
• Inspect mating parts for wear or damage and replace if necessary

Color: White

This replacement wheel installation leg restores mobility and stable support for appliances that use a leg-mounted rolling wheel. It provides a direct-fit restore of worn or damaged legs to help move and position the appliance safely. What it does

• Replaces a damaged or worn wheel-style leg that supports and helps roll the appliance
• Restores smooth rolling and stabilizes appliance during movement
• Helps resolve symptoms like a broken/collapsed leg, stuck wheel, or uneven appliance height
• Matches OEM form and fit for direct replacement when the original leg/wheel is worn

• One wheel installation leg

• Turn off and unplug the appliance and remove contents or shelves as needed before working underneath
• Use basic hand tools; avoid forcing components—reuse existing fasteners