We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dryer won't heat or shows E64 error? High-limit thermostat cuts power if overheating occurs. Moderate DIY fix with our video guide and instructions.
My appliance repair guy checked out the problem, but the stack washer dryer required the contractor to dismantle the cabinet to allow the repair to occur. So i wanted the parts available for the repair, so we would not have to have the dryer pulled apart in a small space for an extended time i ordered the parts on Friday afternoon and they arrived at my home before noon on Saturday! The contractor and the repairman were able to coordinate the repair on Tuesday morning, and though the... Read more
Most orders arrive by Wednesday, November 25
Dryer not drying or taking too long? A worn blower wheel reduces airflow, causing poor drying performance. Moderate DIY repair in 30-45 minutes.
Disassembled dryer. Installed new belt, drum rollers, idler arm and blower. Read more
Dryer won't start or shuts off mid-cycle? This thermal fuse cuts power when overheating occurs. Common fix for E63, E66 errors. DIY repair under 1 hour.
Replaced exhaust thermal cutoff switch. Sears wanted to charge for a service visit + parts and labor. $17 part, $6 shipping and I received the part the following day. Repair complete in less than an hour at a fraction of the cost. Thanks appliance pros. Read more
Dryer not heating or flame goes out after igniting? This flame sensor monitors burner temperature to regulate gas flow. Easy 15-minute DIY repair.
Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more
The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets
Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.
Symptoms of a bad high temperature adhesive include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
I'm new to how a dryer works, so I just started taking it apart to see what exactly was causing it. The video examples on the APP website were all amazing. It gave me a good idea of what I was getting into and showed me the common repair issues. The dryer being 12 years old, I was on the fence about repairing or replacing. However, once I got a list of parts I might need and getting the confidence by watching the videos, I said "what have I got to lose." The cause of the scraping and loud... Read more
Supports and guides the dryer drum as it rotates. Replace if the roller is cracked, worn, or causing noise. Sold individually, not pre-assembled.
ROLLER KIT. INCLUDES 5304523151 SHAFT, 5304523152 ROLLER, 5304523153 NUT 5304523154 SPACER.
I ordered a new motor. Read more
Dryer won't heat or shows E66 error? The thermal limiter prevents overheating by monitoring airflow. Moderate DIY repair, requires rear panel access.
My Electrolux Frigidaire Gas Dryer stopped working and I got an error code E66 that the thermal limiter blew from over heating. The E66 code stops displaying after the initial code and you will then get a door open message. I replaced the thermal limiter and the thermostat just to be sure which part at the problem. The job is hard because you have to take apart the entire dryer and remove the drum. Would be a tough project to complete on your own. Read more
This moisture sensor consists of two metal strips typically mounted inside the dryer drum area that detect the moisture level in clothing during a drying cycle. It signals the control board to end the cycle when clothes reach the desired dryness. Replace this sensor if your dryer shuts off too early with clothes still damp, runs too long, or if the auto-dry cycle no longer functions properly.
Simple unscrewed the set screw, removed the broken sensor-moisture part, attached the leads, and reattached the part to the back of the dryer. Took about 4 minutes. Read more
This high limit thermostat is a safety device that monitors the temperature inside the dryer and cuts power to the heating element if the temperature exceeds a safe threshold. It is typically mounted on the heating element housing or exhaust duct. Replace this thermostat if the dryer is not heating at all or if it overheats - a tripped high limit thermostat often indicates a clogged vent or restricted airflow that should also be addressed.
Replacement air duct assembly with mesh screen for dryers. Installs between drum and heater. Replace if screen is burnt, cracked, melted, or missing.
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more
Dryer not heating? A failed igniter is the most common cause. This part ignites the gas burner for heat. Watch the video for step-by-step replacement.
I looked on Appliance Parts Pros. com and read the problems that others had and replacing the ignitor made sense so I ordered one. It came by UPS within 3 days. I watched the video on how to replace it. Everything went easily, except the screw that held the ignitor in place was a philups head screwdriver and I couldn't get a screwdriver into the small space I had to work in so I went to Harbor Freight Tools and bought an inexpensive 90 degree rachet screwdriver for $2.99 and it worked great.... Read more
This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.
Fix a dryer that won't shut off automatically or has temperature control issues. This thermistor sensor monitors heat levels for proper cycle operation.
I replaced the thermostat. The bearing on the motor was getting loose, so I changed the motor to. The repair took about 2 hours. There are some good re[air videos on the parts web site. Read more
Secures the dryer motor in proper position for stable operation. Replace if motor shifts, buzzes, or clamp strips out. Confirm fit with your model number.
Replace idler, motor mounting clamp and lock Read more
Fix dryer heating issues with this thermistor temperature sensor. Solves intermittent heat, cycle errors, and poor drying. Easy DIY repair.
Replaced all sensors, limiters, thermistors, thermostat. Works great now. Read more
Gas smell during or after cycles? Dryer won't heat? Replace the gas valve assembly to restore proper gas flow and safe operation. Advanced repair.
Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more