Ffq5000 Parts

The Limiter is an OEM replacement part for Frigidaire dryers. Also called a high-limit thermostat, it prevents the dryer from overheating in the event of an obstruction or blockage. The limiter monitors air temperature and airflow inside the dryer drum. 

Symptoms of a bad limiter include:

• The dryer not heating up at all or heating intermittently
• Error codes or failure codes displayed 
• Smelly exhaust from the dryer vent
• Slow or inefficient drying times
• Dryer will not start at all

Causes of a bad limiter can be normal wear and tear over time, failure of internal components, or exposure to overheating conditions from blockages or items not suitable for machine drying. 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Switch is an OEM part for Frigidaire dryers. This part ensures that the dryer operates safely by only allowing the machine to run when the door is completely closed. Positioned typically at the door frame, the switch activates when the door is shut, signaling the control system that it's safe to begin the cycle.

Over time, door switches can wear out or become damaged, which can interfere with the normal operation of the dryer. 

Symptoms of a faulty Door Switch include:

• The dryer not starting when the door is closed.
• The dryer stopping unexpectedly, which might be due to a loose or faulty switch.
• A lack of the usual "click" sound that indicates the door has latched properly, suggesting the switch isn’t engaging.
• The dryer continuing to run when the door is opened, which poses a significant safety risk.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Lint Filter Cover is an OEM part for Frigidaire dryers. This part protects and houses the lint filter. The cover also prevents items from falling into the lint trap area, which could potentially cause blockages or damage to the dryer. 

Causes of a bad Lint Filter Cover can range from physical damage due to accidental impact or improper handling, to normal wear and tear from repeated use.

Symptoms of a bad Lint Filter Cover include:

• Difficulty fitting the cover into its slot, which may indicate warping or damage.
• Visible cracks or breakage on the cover, compromising its ability to secure the lint filter properly.
• Increased lint buildup outside the filter area, suggesting that the cover is not sealing correctly.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Thermostat is an OEM replacement part for Frigidaire dryers. It plays a crucial role in monitoring and regulating the temperature inside the tumbler. The thermostat works closely with the heating element and controls to accurately sense temperature fluctuations and modulate heating levels accordingly.

Symptoms of a bad thermostat include:

• Clothes taking an overly long time to dry
• The dryer is heating excessively and tripping the breaker
• Temperature display or heater lights not functioning
• Clothes drying unevenly, still damp in spots

Causes can be normal wear over extreme heating and cooling cycles. Environmental contaminants may also impact sensor performance.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Color: white. It measures about 13 inches wide by 11-1/2 inches high.

This replacement air duct channels circulation air through the appliance, guiding it between sections to help maintain more even temperatures. A cracked, warped, or missing duct can leak air and reduce overall cooling performance. What it does:

• Routes air from the evaporator/fan to the outlet vents
• Helps balance airflow and temperature between compartments
• Gaps or misalignment can cause weak airflow or warm spots
• Cracks may lead to frost or condensation around the vent area
• Broken tabs or wear can create rattles or looseness

• 1 air duct

• Disconnect power before servicing; wear cut-resistant gloves.
• Remove shelves/covers to access the duct; note screw locations and any nearby sensors or damper components.
• Transfer any reusable foam seals/insulation from the original part and reinstall using existing hardware.
• After reassembly, ensure vents are clear and the fan operates smoothly.

The Door Hinge is an OEM part for Frigidaire dryers. This hinge allows it to open and close properly while maintaining a secure seal during the drying cycle.

Causes of a bad door hinge can include wear and tear from regular use, rust or corrosion due to exposure to moisture, or damage from accidental impacts. 

Symptoms of a bad door hinge include:

• Difficulty opening or closing the dryer door
• The door not sealing properly, leading to heat loss
• Squeaking or creaking noises when moving the door
• Visible damage or rust on the hinge

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The Adjustable Foot is an OEM part for Frigidaire dryers. This part is located at the bottom of the dryer and allows you to level it, ensuring stability and proper operation. 

Causes of a bad adjustable foot can include regular wear and tear, damage from moving the appliance, or breaking due to excessive weight or stress.  

Symptoms of a bad adjustable foot include:

• The dryer wobbling or tilting
• Difficulty in adjusting the height of the foot
• Visible damage or deformation of the foot
• Unusual noises or vibrations during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This idler spring attaches to the idler arm to keep the drive belt properly tensioned, preventing slip and chatter. Replacing a weak or broken spring restores steady rotation and helps reduce noise and belt wear.

• Maintains correct belt tension by pulling the idler arm into position
• Helps prevent belt slippage, squealing/chirping, and premature belt wear
• A failed spring can cause no or intermittent rotation and the belt coming off
• Typical signs include a loose belt, off-track belt, or rhythmic squeak from the base

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Access the idler assembly; note belt routing before removal
• Relieve belt tension, then move the idler arm to remove and replace the spring on the same mounting holes
• After reassembly, rotate by hand to verify smooth belt tracking before test

This replacement gasket restores a tight, reliable seal between mating parts in your appliance. It helps contain water or air at the joint to prevent leaks, odors, and performance issues.

• Creates a compressible barrier that prevents leaks at the sealed interface
• Helps maintain proper containment/airflow, depending on application
• Replace if torn, cracked, shrunken, or permanently flattened
• Typical symptoms include moisture or drips at the seam, musty odors, or visible damage

• Disconnect power; shut off water supply if applicable before servicing
• Use your model's parts diagram to locate and orient
• Clean and dry mating surfaces; remove any old adhesive or residue so the new seal seats properly
• Reassemble evenly, avoid over-tightening fasteners, and test for leaks after reassembly

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This EMI line filter reduces electrical interference on the incoming power to help protect the appliance's electronics and ensure stable operation. A failed filter can leave the unit dead, intermittently power-cycling, or tripping a breaker.

• Filters electromagnetic interference (EMI) on the AC line
• Helps protect the control board and other sensitive circuits
• Common symptoms: no power, intermittent power, or breaker/fuse trips when the unit starts
• Typically located near the power-cord entry or main control

• Disconnect power before servicing; allow a few minutes for any capacitors to discharge
• Note and label wire positions; move wires one at a time to the new filter
• Secure the filter to its mounting bracket and ensure the ground connection is tight
• Inspect wiring for shorts or damage before restoring power and testing

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This moisture sensor monitors dampness inside the dryer drum and signals the control when fabrics are dry, helping automatic cycles end on time and avoid overdrying. Replacing a failed sensor can restore consistent Auto Dry performance and cycle times. What it does:

• Detects moisture level via conductivity across the sensor surfaces inside the drum
• Sends feedback to the control so Auto Dry cycles advance and stop correctly
• Helps prevent overdrying and underdrying in sensor-based cycles
• Common symptoms of a faulty sensor may include: auto cycles ending too soon or running too long, clothes remaining damp, or the dryer staying on "Sensing" while timed cycles still work

• 1 moisture sensor

• Disconnect power and, if applicable, shut off gas before servicing
• Access the sensor at the front bulkhead/lint housing area; remove front panel as needed per model
• Transfer connectors and route wiring exactly as original; secure the sensor firmly
• Clean the sensor contact surfaces with rubbing alcohol; residue from dryer sheets or fabric softeners can affect readings

This glow-bar igniter lights the gas burner in your dryer so it can produce heat. When the igniter is cracked, weak, or open, the burner won't light and clothes won't dry properly.

• Heats up to ignite the gas burner during each heating cycle
• Common symptoms of failure: no heat, takes too long to dry, burner won't light, igniter doesn't glow or glows but no flame
• Restores consistent ignition and drying performance

• Unplug dryer and shut off gas supply before servicing
• Handle the igniter carefully—ceramic element is fragile; avoid touching it with bare fingers
• Note wire routing and burner alignment before removal
• After installation, restore gas/electric and check for proper burner ignition