Gd2shaxnq Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Too warm
• Clicking sound
• Won't start
• Freezer section too warm

I have a Kitchen Aid side by side refrigerator/freezer which is 8 years old. One day it just stopped cooling. At first I was just going to junk it and purchase a new one. However, I took off the lower back cover and noticed the compressor was not running. I knew from experience that these compressors need a starter capacitor and relay and it is not uncommon for these parts to fail. I looked on the Internet for a video which showed how to remove the parts. I also found a video which showed how... Read more

• Frost buildup
• Freezer not defrosting
• Freezer section too warm
• Fridge too warm

Condenser was encased in solid block of ice due to automatic defrost not working. Replaced thermostat and ADC control board. Working fine now. Most tedious part was using a heat gun to melt all the ice off the condenser coils. You will need a couple small wire nuts to splice the new thermostat into the existing harness (they are not included). Service tech wanted over $400 to repair, fixed it myself for half that. Thanks ! Read more

• Door sweating
• Door won't open or close
• Clicking sound
• Fridge too warm

Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side... Read more

• Door won't open or close
• Door sweating
• Fridge too warm
• Noisy

Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side... Read more

I watched the video on replacing the switch on a side freezer where prying out to original switch did not look difficult. I then got on the floor and tried to pry out my switch. Had a terrible time (locking tab or switch body hardened with time?) and mangled the switch terribly and the upper panel of the freezer somewhat, but the switch did come out. AND THEN the top freezer panel with the switch and light assembly fell out into my hands! I was able to unplug one Molex connector and the... Read more

• Ice maker dispenses too little ice
• Not dispensing water
• Touchpad does not respond
• Leaking

I'm such a pro, I figured I needed a new hose for my water dispenser so I ordered it. When it arrived I called my handyman. He told me I did not need a hose I needed A cartridge. So I had to return the hose and order the cartridge! Your company was so cooperative and made the return so easy Thank you! Next time I call the handyman first! Read more

My refrigerator was not dispensing ice. I could hear the motor activating but noticed the ice auger was not turning. My old drive shaft was stripped on both ends. Video was very helpful and it was an easy fix for someone with little handyman experience. Received my order much faster than expected! The parts arrived the next day and paid for the standard shipping charge. I live in Texas. Read more

First Problem - WATER INLET VALVE - After having problems with ice maker not making ice, I troubleshot and replaced the water inlet valve. Video and instructions were excellent. With 16 year old fridge, the water lines had compression fittings in the old valve, so had to cut the fittings off with a razor blade to allow the lines to insert into the new valve press-in type fittings. Worked great / no leaks at the new valve. But, new leaks occurred at the water filter housing spraying down into... Read more

• Ice maker dispenses too much ice

Ice Door Kit, Control Bracket, and Ice Dispenser Guide were purchased. I followed two videos on replacing the parts. The Control Bracket WP2180226 / AP6005965, was straight forward and I discovered a snapped pin on the old bracket causing an electric switch to be out of place... that repair was easy. When it came to the hinges of the ice chute, I discovered the snap-in, on right side, of the hinge was cracked... this is why the pin escaped. This cracked part is molded into the entire... Read more

Replaced door switch - it took less than 5 minutes - works perfectly Read more

• Ice maker not making ice
• Ice maker won't dispense ice

SO I FIGURED THAT ALL THE MECHANICAL PARTS OF IT WERE FINE SO THE LOGICAL THING TO DO WAS TO REPLACE ELECTRICAL COMPONENTS WHICH CONSISTED OF THE THERMOSTAT {THE BRAIN} AND THE CONTROL MODULE WHICH I PURCHASED AT A VERY REASONABLE PRICE . I REASSEMBLED THE UNIT AND IT HAS BEEN WORKING LIKE NEW EVER SINCE. THANK YOU! Read more

• Noisy
• Fridge runs too long
• Fridge too warm
• Freezer section too warm

Unplugged refrigerator and removed access panel from back of fridge. Have had this panel off many times for dust removal. Panel is a cheap piece of glorified cardboard on this Whirlpool model, which is a shame given that it was a $1000 refrigerator. Fan motor is mounted on stamped sheet metal bracket which I removed from cabinet with old fan attached to it. Metal bracket held in place by 4 1/4 inch hex head sheet metal screws. Two outermost screws can be removed with nut driver but access to... Read more

Removed trays. Trap broken tracks back to notch in order up lock and remove them. in stalled new replacement tracks but first sand down flat the two circular taps that were no allowing the tracks two get flush with the wall surface. Clean wall surface of any build up spills. rub on a light coat of liquid soap which will help you slide the track in and seats. Read more

• Noisy
• Fridge too warm

The fridge is 20+ years old in a home we recently moved into. It sounded like a motor getting stuck on something or grinding weird... was hoping it wasn't something more serious. Found this site, clicked 'noisy' and got the replacement evaporator fan motor blade as well as the motor evaporator. Turned out I didn't really need to replace the fan blade, but since I had it and ours was old, figured I might as well put in the new parts. Followed the videos here, which were really helpful. The... Read more

Test showed it was the infrared sensor, so I ordered the replacement parts, which arrived with standard shipping in just a couple of day. The video on the site show exactly what to do. The fix and installation of the replacement part was quick and easy. My ice maker is producing ice like bran knew. I could not be happier with the service and information provided by this site. Great job guys, really great job. Read more